Difference between revisions of "Category:1006 Aggregate for Surfacing"
(→1006.2 Acceptance: Lower types of aggregate for surfacing by certification or visual inspection for small quantitites are now allowed since sampling may not be practical.) |
m (Per CM, removed archaic SiteManager info and replaced with AASHTOWARE info) |
||
| (6 intermediate revisions by the same user not shown) | |||
| Line 3: | Line 3: | ||
|'''MGS Information''' | |'''MGS Information''' | ||
|- | |- | ||
| − | |[ | + | |[https://www.modot.org/general-services-specifications-mgs-subject Current General Services Specifications (MGS) By Subject] |
|} | |} | ||
| Line 12: | Line 12: | ||
==1006.1 Procedure== | ==1006.1 Procedure== | ||
Inspection, testing, and sampling will be governed by the instructions | Inspection, testing, and sampling will be governed by the instructions | ||
| − | contained in [[:Category:1001 General Requirements for Material|General Requirements for Material]]. | + | contained in [[:Category:1001 General Requirements for Material|EPG 1001 General Requirements for Material]]. |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
Samples required for Laboratory tests are as follows: | Samples required for Laboratory tests are as follows: | ||
| Line 31: | Line 18: | ||
==1006.2 Acceptance== | ==1006.2 Acceptance== | ||
| − | Acceptance is based on routine tests in the field to ensure compliance with [http://modot. | + | Acceptance is based on routine tests in the field to ensure compliance with [http://www.modot.org/business/standards_and_specs/SpecbookEPG.pdf#page=14 Sec 1006]. Samples are to be taken at destination or at the source of aggregate production by MoDOT inspectors at intervals of one per 2,000 tons. For small quantity jobs see Sec 1006. |
==1006.3 Records and Reports== | ==1006.3 Records and Reports== | ||
| − | All plant records shown in [[:Category:1001 General Requirements for Material#1001. | + | All plant records shown in [[:Category:1001 General Requirements for Material#1001.6 Records and Reports|EPG 1001.6 General Requirements for Material - Records and Reports]] shall be maintained. The aggregates shall be reported through AASHTOWARE Project (AWP) in accordance with [[:Category:101 Standard Forms #Sample Record, General|AWP MA Sample Record, General]]. |
==1006.4 Laboratory Procedure for Sec 1006== | ==1006.4 Laboratory Procedure for Sec 1006== | ||
===1006.4.2 Types of Samples Tested=== | ===1006.4.2 Types of Samples Tested=== | ||
====1006.4.2.1 Initial Approval Sample==== | ====1006.4.2.1 Initial Approval Sample==== | ||
| − | Tests consist of specific gravity, absorption, and Los Angeles abrasion. The minimum time required for completion of tests is four working days from the date received. Test results and calculations shall be recorded through | + | Tests consist of specific gravity, absorption, and Los Angeles abrasion. The minimum time required for completion of tests is four working days from the date received. Test results and calculations shall be recorded through AWP. |
===1006.4.3 Procedure=== | ===1006.4.3 Procedure=== | ||
| Line 55: | Line 42: | ||
===1006.4.4 Sample Record=== | ===1006.4.4 Sample Record=== | ||
| − | The sample record shall be completed in | + | The sample record shall be completed in AASHTOWARE Project (AWP) in accordance with [[:Category:101 Standard Forms #Sample Record, General|AWP MA Sample Record, General]], and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in [[106.20 Reporting|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab. |
Latest revision as of 06:51, 16 September 2021
| MGS Information |
| Current General Services Specifications (MGS) By Subject |
This guidance establishes procedures for the inspection, testing and acceptance of aggregate for
surfacing.
Contents
1006.1 Procedure
Inspection, testing, and sampling will be governed by the instructions contained in EPG 1001 General Requirements for Material.
Samples required for Laboratory tests are as follows:
- (a) Initial Evaluation required if material has never been tested before.
1006.2 Acceptance
Acceptance is based on routine tests in the field to ensure compliance with Sec 1006. Samples are to be taken at destination or at the source of aggregate production by MoDOT inspectors at intervals of one per 2,000 tons. For small quantity jobs see Sec 1006.
1006.3 Records and Reports
All plant records shown in EPG 1001.6 General Requirements for Material - Records and Reports shall be maintained. The aggregates shall be reported through AASHTOWARE Project (AWP) in accordance with AWP MA Sample Record, General.
1006.4 Laboratory Procedure for Sec 1006
1006.4.2 Types of Samples Tested
1006.4.2.1 Initial Approval Sample
Tests consist of specific gravity, absorption, and Los Angeles abrasion. The minimum time required for completion of tests is four working days from the date received. Test results and calculations shall be recorded through AWP.
1006.4.3 Procedure
1006.4.3.1 Sieve Analysis
Aggregate shall be tested in accordance with AASHTO T 27.
1006.4.3.2 Specific Gravity and Absorption
Aggregate shall be tested according to AASHTO T 85 for Bulk Specific Gravity.
1006.4.3.3 Los Angeles Abrasion
Aggregate shall be tested in accordance with AASHTO T96.
1006.4.3.4 Deleterious Content
The percentage of deleterious substances in coarse aggregate shall be determined according to TM-71, Deleterious Content of Aggregate. Where field determinations show a total deleterious content of 4.0 percent or less, including not more than 2.5 percent mud balls, the deleterious content is to be inspected visually. The sample is to be tested if visual inspection indicates more than 4.0 percent total deleterious material present in the sample. Source approval samples shall always be tested regardless of the content of deleterious material.
1006.4.4 Sample Record
The sample record shall be completed in AASHTOWARE Project (AWP) in accordance with AWP MA Sample Record, General, and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in EPG 106.20 Reporting, are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.
