Difference between revisions of "Category:240 Maintenance and Emergency Crossovers"

From Engineering_Policy_Guide
Jump to navigation Jump to search
m (article construction)
m (add link to "interchange facilities")
Line 3: Line 3:
 
:* provide ample access for law enforcement or emergency medical services responding to roadway incidents.
 
:* provide ample access for law enforcement or emergency medical services responding to roadway incidents.
  
Maintenance crossovers may be needed at one or both ends of interchange facilities, depending on the type of interchange.
+
Maintenance crossovers may be needed at one or both ends of [[:Category:234 Interchanges|interchange facilities]], depending on the type of interchange.
  
 
Public [[:Category:233 At - Grade Intersections|at-grade intersections]] or crossovers are not constructed on fully controlled access routes.  [[233.2 At-Grade Intersections with Stop and Yield Control#233.2.1.2 Median Openings|Median openings]] are considered at intervals outlined in [[940.7 Median Opening Spacing| 940.7 Median Opening Spacing]] on other routes.
 
Public [[:Category:233 At - Grade Intersections|at-grade intersections]] or crossovers are not constructed on fully controlled access routes.  [[233.2 At-Grade Intersections with Stop and Yield Control#233.2.1.2 Median Openings|Median openings]] are considered at intervals outlined in [[940.7 Median Opening Spacing| 940.7 Median Opening Spacing]] on other routes.

Revision as of 13:08, 3 December 2007

Maintenance and emergency crossovers may be constructed on freeways and expressways so that maintenance, emergency and law enforcement vehicles can avoid extremely adverse distances. These crossovers

  • facilitate maintenance activities such as snow removal and
  • provide ample access for law enforcement or emergency medical services responding to roadway incidents.

Maintenance crossovers may be needed at one or both ends of interchange facilities, depending on the type of interchange.

Public at-grade intersections or crossovers are not constructed on fully controlled access routes. Median openings are considered at intervals outlined in 940.7 Median Opening Spacing on other routes.

The Federal Highway Administration must approve maintenance and emergency crossovers on interstates. The State Maintenance Engineer must approve maintenance and emergency crossovers on all other state routes.

240.1 Location

When selecting a location for a maintenance and emergency crossover, the guidance contained in AASHTO’s A Policy on Geometric Design of Highways and Streets should be used in addition to the following general guidelines:

1. Maintenance and emergency crossovers should not be located closer than 1,500 ft. to the end of a speed-change ramp or to any structures such as bridge columns or guardrail located in the median.

2. Maintenance and emergency crossovers should be located only where the Design Entering Sight Distance is provided.

3. Maintenance and emergency crossovers should not be located within curves requiring superelevation.

4. Spacing of crossovers should be every 2.5 miles, and

5. Interchanges that are closer than 2.5 miles apart should not have maintenance and emergency crossovers unless a defined need exists for maintenance, emergency, medical or law enforcement purposes.

240.2 Request for Crossover by Maintenance Personnel

The following information is required when submitting a request to construct a new maintenance and emergency crossover on an existing route:

1. A letter of transmittal to the State Maintenance Engineer stating the route, county and exact station number of the proposed crossover. The request should contain a general statement regarding the need for the crossover, the sight distance in both directions of the proposed crossover, the effect on the median drainage and a statement that the crossover changes are acceptable to the local emergency responders.

2. A general county highway map showing the location of the proposed crossover and all existing crossovers and interchanges within 5 miles on either side of the proposed crossover.

3. A copy of the plan-profile sheet for the section of roadway where the proposed crossover will be located.

240.3 Maintenance and Emergency Crossover Construction Requirements

1. Crossovers shall be constructed with an aggregate surface no wider than 20 ft. and with turning radii of not more than 10 ft.

2. To be inconspicuous to mainline traffic, the surface should be depressed below shoulder level.

3. Sideslopes should be constructed 1V:10H or flatter to minimize their effect as obstacles to uncontrolled vehicles that may enter the median.

4. If possible, the crossover should be located where a pipe is not necessary. All drainage structures constructed in the median must be built to current safety standards. Refer to Standard Plan 606.41 for drainage piping plans and pipe end treatment options.

5. The surface shall not be upgraded to a higher type surface.

6. Crossovers are to be in good repair at all times.

7. Signing for a maintenance and emergency crossover shall be in accordance with 903.5.53 AUTHORIZED AND EMERGENCY VEHICLES ONLY.