Difference between revisions of "Category:1062 Pull and Junction Boxes"
(info from materials manual) |
m (→1062.2 Procedure: article construction) |
||
| Line 16: | Line 16: | ||
===1062.2.2 Preformed Pull Boxes=== | ===1062.2.2 Preformed Pull Boxes=== | ||
| − | Acceptance of preformed polyester resin mortar, preformed resin mortar and fiberglass pull boxes is to be based upon current listing of the manufacturer and model number on the Traffic Operations approved products list, manufactures certification and examination of dimensions and workmanship to determine conformance to the applicable standard plan and [http://www.modot.mo.gov/business/standards_and_specs/Sec1062.pdf Sec 1062]. The manufacturer's certification for pull boxes shall state that the material supplied conforms to all of the requirements specified. | + | Acceptance of preformed polyester resin mortar, preformed resin mortar and fiberglass pull boxes is to be based upon current listing of the manufacturer and model number on the Traffic Operations approved products list, manufactures certification and [[:643.3 Policy, Standards and Regulations#643.3.1.3 Definitions and General Information|examination of dimensions]] and workmanship to determine conformance to the applicable standard plan and [http://www.modot.mo.gov/business/standards_and_specs/Sec1062.pdf Sec 1062]. The manufacturer's certification for pull boxes shall state that the material supplied conforms to all of the requirements specified. |
Inspection of preformed pull boxes should identify any structural concerns, such as fiber mesh not covered by resin mortar in a localized area, areas that can be penetrated by physical means due to voids or less dense material, or visible cracks especially around the mounting lag nuts. | Inspection of preformed pull boxes should identify any structural concerns, such as fiber mesh not covered by resin mortar in a localized area, areas that can be penetrated by physical means due to voids or less dense material, or visible cracks especially around the mounting lag nuts. | ||
| Line 22: | Line 22: | ||
===1062.2.3 Concrete Pull Box Frames and Covers and Cable Hooks=== | ===1062.2.3 Concrete Pull Box Frames and Covers and Cable Hooks=== | ||
| − | Concrete pull box frames and covers and cable hooks are to be accepted on the basis of a manufacturer's certification and examination of dimensions, weight (mass) and workmanship to determine conformance to Sec 1062. The manufacturer's certification for cast iron frames and covers is to show the class of cast iron and certify that the material supplied conforms to all of the requirements specified. | + | Concrete pull box frames and covers and cable hooks are to be accepted on the basis of a manufacturer's certification and [[:643.3 Policy, Standards and Regulations#643.3.1.3 Definitions and General Information|examination of dimensions]], weight (mass) and workmanship to determine conformance to Sec 1062. The manufacturer's certification for cast iron frames and covers is to show the class of cast iron and certify that the material supplied conforms to all of the requirements specified. |
===1062.2.4 Junction Boxes=== | ===1062.2.4 Junction Boxes=== | ||
Revision as of 07:59, 18 May 2007
This article establishes procedures for inspecting, sampling and reporting pull boxes, junction boxes and pull box frames and covers. Refer to Sec 1062 for MoDOT’s specifications.
Contents
1062.1 Apparatus
- (a) Magnetic gauge, reading range of 0-40 mils (0-1000 m).
- (b) Rule with suitable graduations to accurately measure the material to be inspected.
1062.2 Procedure
1062.2.1 Precast Concrete Pull Boxes
Acceptance of precast concrete pull boxes is to be based on the inspection of materials being incorporated into the boxes and inspection of the finished box. Compressive tests and absorption test specimens will not be required.
1062.2.2 Preformed Pull Boxes
Acceptance of preformed polyester resin mortar, preformed resin mortar and fiberglass pull boxes is to be based upon current listing of the manufacturer and model number on the Traffic Operations approved products list, manufactures certification and examination of dimensions and workmanship to determine conformance to the applicable standard plan and Sec 1062. The manufacturer's certification for pull boxes shall state that the material supplied conforms to all of the requirements specified.
Inspection of preformed pull boxes should identify any structural concerns, such as fiber mesh not covered by resin mortar in a localized area, areas that can be penetrated by physical means due to voids or less dense material, or visible cracks especially around the mounting lag nuts.
1062.2.3 Concrete Pull Box Frames and Covers and Cable Hooks
Concrete pull box frames and covers and cable hooks are to be accepted on the basis of a manufacturer's certification and examination of dimensions, weight (mass) and workmanship to determine conformance to Sec 1062. The manufacturer's certification for cast iron frames and covers is to show the class of cast iron and certify that the material supplied conforms to all of the requirements specified.
1062.2.4 Junction Boxes
Junction boxes are to be accepted on the basis of a manufacturer's certification and examination of dimensions and workmanship to determination conformance to Sec 1062.
1062.3 Report
Reports shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in Reporting Test Results, are to be included in the report to clarify conditions of acceptance or rejection.
Items in this section shall be reported through SiteManager. The manufacturer's certification, when required, shall be retained in the district office.
