751.13 Expansion Joint Systems

Preformed Compression Joint Seal	Strip Seal
Flat Plate	Finger Plate

751.13.1 Expansion Devices

751.13.1.1 General

The number of movable deck joints in a structure should be minimized. Deck joints should be avoided over roadways, railroads, sidewalks, other public areas, and at the low point of sag vertical curves.

Consult the Structural Project Manager, if the use of special covering floor plates in shoulder areas should be considered.

If no expansion device is specified in the Design Layout, but due to the length of structure an expansion device is required, consult the Structural Project Manager for the type to be used. The roadway surface gap, W, (Except Flat and Finger Plates) in a transverse deck joint, measured in the direction of travel shall satisfy:

For single gaps:

1" ≤ W ≤ 4"

EXPANSION JOINT SELECTION
	Allowable Movement	Allowable Skew
Preformed Compression Joint Seal	0 – 2”	≤ 20˚
Strip Seals	2” to 4”	≤ 45˚
Flat Plate		> 45˚
Finger Plate

Movement Calculation (in the direction of travel)

$\,\triangle =\gamma (coefficient)(temperature\ range)(actual\ expansion\ length)$

$\,\gamma$ = Load factor for temperature movement

Coefficients, ($\,\alpha$)

Steel:	Thermal - 0.0000065 ft/ft/F°
Concrete:	Thermal - 0.0000060 ft/ft/F°

Temperature Range From 60°F, ($\,\alpha$)

Temperature Range is based on a design installation temperature of 60°F.

	Rise	Fall	Range
Steel Structures	60°F	90°F	150°F (From -30° to 120°)
Concrete Structures	50°F	70°F	120°F (From -10° to 110°)

Actual Expansion Length, (L)

When Expansion joints are used for long span structures with deep girders, movement calculations should also consider the bearings and possible resulting girder rotation.

Installation Width
The installation width, gap, should be adjusted for temperatures above or below the design installation temperature. Movement for a 10°F change in temperature should be indicated on the plans to the nearest 1/16” by using the appropriate note.

Movement for 10°F change in temperature = (α)(10°F)(L)(Cos θ)

751.13.1.2 Expansion and Contraction Length

Note:

= Expansion and contraction length.

For configurations not shown, a temperature force distribution analysis may be necessary to estimate the point of thermal origin.

751.13.1.3 Expansion Device on Skewed Curved Structures

Expansion Device on Skewed Curved Structures

Add the “Section Thru Centerline Expansion Gap” and the Table shown below to the Expansion Device sheet for skewed curved structures.

PART PLAN

SECTION THRU $\,\ C_{\!\!\!\!L}$ EXPANSION GAP

BENT NO.	GRADE ELEVATION			ANGLE		HORIZONTAL DIMENSIONS
	LEFT GUTTER LINE	$\,\ C_{\!\!\!\!L}$ RDWY.	RIGHT GUTTER LINE
				"A"	"B"	"C"	"D"	"E"	"F"

751.13.1.4 Details of Substructure Protection

A protective coating shall be applied to concrete surfaces exposed to drainage from the roadway. Indicate surface to be coated on plans. Urethane resembles black tar which is used where aesthetics is not a concern, otherwise use epoxy.

Note: Epoxy coat all reinforcement in end bents with expansion joint system.

751.13.2 Silicone Expansion Joint Sealant

Silicone expansion joint sealant systems (SEJS) shall not be used for normal contract new or rehabilitation jobs effective November 2011. This system is considered a short term sealing solution primarily good for maintenance operations.

SEJS may be considered for special situations when agreed upon by both the district bridge engineer and Bridge Division. Examples include short deck spans, sawed joints or situations where contracted joint work is intended to supplement MoDOT’s bridge maintenance work scheduling (maintenance type applications).

Archived SEJS details including armor and reinforcing steel details are available upon request from the Bridge Division.

751.13.3 Preformed Compression Joint Seal

751.13.3.1 General

The system can be used for movements up to 2" with skews ≤ 20°.

PART CROSS-SECTION THRU EXPANSION JOINT

TABLE OF TRANSVERSE BRIDGE SEAL DIMENSIONS
SEAL WIDTH (Wn)			REQUIRED MOVEMENT RANGE (M $\,\bot$)	MIN. JOINT WIDTH ($\,\bot$ TO JOINT)	MAX. JOINT WIDTH ($\,\bot$ TO JOINT)
2.5"	1 9/16"	MANUFACTURER'S RECOMMENDED HEIGHT	1.00"	1.13"	2.13"
3.0"	1 7/8"	MANUFACTURER'S RECOMMENDED HEIGHT	1.20"	1.34"	2.55"
3.5"	2 3/16"	MANUFACTURER'S RECOMMENED HEIGHT	1.40"	1.58"	2.98"
4.0"	2 7/16"	MANUFACTURER'S RECOMMENED HEIGHT	1.65"	1.75"	3.40"
4.5"	2 13/16"	MANUFACTURER'S RECOMNENED HEIGHT	1.80"	2.03"	3.83"

Size of Armor Angle:
Vertical leg of angle shall be a minimum of + 3/4", horizontal leg of angle shall be a minimum of 3". Minimum thickness of angle shall be 1/2".

Check 1" ≤ w ≤ 4" after select seal size, w = gap at top slab in the direction of travel, in inch.

751.13.3.2 Steel Structure Details

SECTION B-B

PART PLAN

DETAIL "B"	DETAIL "A"

751.13.3.3 Prestressed Structure Details

SECTION B-B

PART PLAN

DETAIL "B"	DETAIL "A"

751.13.3.4 Barrier Curb Details

Part Section A-A * Extend preformed compression joint seal 3” past edge of slab (Typ.) Note: Drainage details should be handled similar to drainage details for strip seals.

Part Elevation of Barrier Curb

Square Structure

Skewed Structure Note: The working point is always placed on the front face side of backwall at the gutter line.

751.13.3.5 Sidewalk Details

PART SECTION THRU CENTER OF EXPANSION DEVICE

PART SECTION A-A

(*) See Project Manager for direction of slope.

751.13.3.6 Double Faced Median Barrier Bridge Curb

Part Section A-A Note: Use continuous joint seal thru the median barrier curb only when slab cross-slope slopes away from curb or slab is superelevated.

Part Elevation of Barrier Curb

751.13.4 Strip Seal Expansion Joint System

751.13.4.1 General

Strip Seal Expansion Joint Systems should be used for movements greater than 2” and less than 4” for skews < 45°. Use flat plate expansion devices on curved structures and skews over 45°.

The installation width, gap = 2”, based on a design installation temperature of 60°F.

On skewed bridges, the strip seal expansion devices must be checked for parallel and perpendicular movements. Parallel movements (Racking) shall be less than 1 ½” for either rise or fall movements. Maximum skew shall be 45°.

Formulas: M = 1.2(ΔT)(α)(L) : Bridge total movement or individual rise and fall movements

ΔT = Corresponding temperature range

L = Expansion length

α = Coefficient of linear expansion

M$\,\bot$ = M cos θ : Movement perpendicular to joint
M$\,\ ||$ = M sin θ : Movement parallel to joint

θ = skew angle

Gland Size

Strip Seal Gland Size	Gap at Top Slab (60°F)	Min. Joint Width ($\,\bot$ to Joint)	Max. Joint Width ($\,\bot$ to Joint)	Max. Gap ($\,\ ||\ C_{\!\!\!L}$ Rdwy)
3”	2”	1”	3”	4”
4”	2”	1”	4”	4”

751.13.4.2 Gland Extrusion Details

DETAIL OF JOINT ARMOR

DETAIL OF GLAND

751.13.4.3 Joint System Details (Steel Structures)

SECTION B-B
* Do not show dimension on plans.

PART PLAN

DETAIL "A"

DETAIL "B"

(**) Dimension required to clear bearing stiffener (1 1/2" Min.). (Dimension to be shown on plans)

SECTION B-B

PART PLAN

DETAIL "A"

DETAIL "B"

(**) Dimension required to clear bearing stiffener (1 1/2" Min.). (Dimension to be shown on plans)

751.13.4.4 Joint System Details (Prestressed Structures)

(**) 3/4" Min. (Do not show on plans.)

SECTION B-B

PART PLAN

DETAIL "B"	DETAIL "A"

(*) Dimension required along centerline of girder (Dimension to be shown on plans).

(**) 3/4" Min. (Do not show on plans.)

SECTION B-B

PART PLAN

DETAIL "B"	DETAIL "A"

(*) Dimension required along centerline of girder (Dimension to be shown on plans).

751.13.4.5 Barrier Curb Details

Part Elevation of Barrier Curb

Section Thru Joint

Part Plan (Square Bridge)

Part Plan (Skewed Bridge) * Working Point is always at front face of backwall at gutterline.

Barrier Curb at End Bents

Elevation	Part Section A-A
Part Plan B-B (Square)	Part Plan B-B (Skewed)

751.13.4.6 Double Faced Median Barrier Curb Details

For details not shown of median barrier bridge curb, see the safety barrier curb details, Design Division Standard Plans (Concrete Median Barrier) and Bridge Design Layout.

Part Section A-A Note: Use continuous strip seal thru median curb only when slab cross-slope slopes away from curb or slab is superelevated.

Part Elevation of Barrier Curb

751.13.4.7 Drainage Details

In order for strip seal expansion joint systems to function properly, the gland shall be allowed to drain to prevent build-up of debris. Debris may punch holes in the gland and the extra load may possibly pull the gland from the extrusions.

To prevent debris buildup on the strip seals the gland should not be turned up at the barrier curb. Instead, the steel armor with extrusions should be extended to the face of the slab through the barrier curb.

Drainage shall be handled by one of two methods. The first method is to let the water run off the gland and free fall to the ground below. The gland should extend past the edge of slab 3 inches minimum. At intermediate bents, the bent cap should have a protective coating applied to prevent moisture saturation of the concrete. On structures where there is an adjacent structure separated by a median barrier curb with an open joint (Type D or Split Median) the gland should be terminated at some point under the curb at all bent types and protective coating should be applied at all faces exposed to moisture. The second method of drainage is to provide a fiberglass pipe drainage system to collect water at the bents.

See the Structural Project Manager for the method of drainage to be used. The following pages provide some possible details that may be used for strip seal expansion joint drainage systems.

If the fiberglass pipe drainage system is used, payment will be made under the pay item. Drainage System (On structure), Lump Sum.

Option #1- No Drainage System, at End Bent

Option #1- No Drainage Sytem, at Split Median Barrier Curb at Intermediate Bent

Option #2 - One-Piece Drain System at End Bent

FRONT ELEVATION

PART SECTION A-A

SIDE ELEVATION

Option #2 - One-Piece Drain System, Split Median Barrier Curb at End Bent

FRONT ELEVATION

SECTION THRU BENT

Option #2 - One-Piece Drain System, Intermediate Bent

DETAIL A

(Optional)

Option #2 - One-Piece Drain System at Split Median Barrier Curb at Intermediate Bent

SECTION THRU JOINT

Note: If dropping water to ground from bottom of beam is not allowed, an additional pipe system shall be used.

SECTION A-A

Option #3 - Three-Piece Drain System at Split Median Barrier Curb at Intermediate Bent

SECTION THRU JOINT

SECTION B-B

SECTION C-C

SECTION D-D

(*)Varies (Space holes to clear B1 bars in P/S girders. Use 6" for plate girders.)

SECTION E-E

751.13.4.8 Polymer Concrete

Strip Seal Expansion Joint System may be used on rehabilitation projects where other expansion devices need to be replaced. Consult with Structural Project Manager about the use of polymer concrete with strip seals. Strip seal is to be designed with the same requirements as a normal strip seal expansion joint system.

Note: Anchorage system shall be welded to strip seal steel armor with appropriate weld to meet AASHTO Fatigue for connection.

DETAIL OF SINUSOIDAL BAR

Note: A pay item exists for this type of expansion joint system. The system will be paid for under Strip Seal Expansion Joint System per linear foot. Polymer Concrete will be paid for under Polymer Cocrete per cubic foot.

DETAIL OF SHEAR CONNECTOR

(Alternate #4 reinforcing bar shall be bent similarly)

751.13.5 Flat Plate Expansion Devices

751.13.5.1 General

Flat Plate Expansion Joint System should be used where Strip Seals and Preformed Compression Joints can not be used due to large expansion lengths or curved structures or skews over 45˚.

The installation width, sub-surface gap = 3 1/2 in. is based on a design installation temperature of 60˚F.

Design movement for Flat Plate Expansion Devices is limited by the following criteria:

1. Full closure of surface gap.

2. Min. sub-surface gap = 1 in. (┴ to joint)

3. Min. plate overlap = 1 1/2 in. (┴ to joint)

Note: Criterion 3 controls for standard details for both concrete and steel superstructures. Originally, the details for EPG 751.13.5 used a 3/4 in. x 7/8 in. bar, that allowed for a 2 ½ in. gap contraction (┴ to joint). Functionally, the 3/4 in. x 7/8 in. bar is preferred but it is not available domestically as of July 2010. A 7/8 in. x 7/8 in. bar is shown as the standard in EPG 751.13.5 primarily due to domestic availability.

Flat Plate expansion devices can be used bridges of any skew.

Maximum Expansion Length1
Skew	Concrete Bridge	Steel Bridge
0°	496 ft.	356 ft.
10°	504 ft.	362 ft.
20°	528 ft.	379 ft.
30°	573 ft.	411 ft.
40°	648 ft.	465 ft.
50°	772 ft.	554 ft.
60°	992 ft.	712 ft.
1 This table is applicable for standard details found in EPG 751.13.5 and for joints where movement is expected from one side of the joint. When movement is expected from both sides of the joint, the sum of the expansion lengths participating at a joint should not exceed the values in this table. When larger expansion lengths are required, the surface gap, sub-surface gap and flat plate dimensions shall be determined by design.

The max. surface gap requirement, W ≤ 4 in. is not considered for flat plate expansion devices since the surface gap neither impairs the riding characteristics of the roadway, nor damages vehicles nor destroys the function of the joint.

Dimensions shown are perpendicular to centerline of joint and do not vary with skew.

Part longitudinal sections for bridges on grades or verticle curves having a plate type intermediate expansion device shall be detailed with the expansion plate anchor to the long span side. If equal spans, then place expansion plate anchor on the high side. For bevel plate and permissible field splice details, see Bridge Standard Drawings.

Slotted wells in prestressed girders shall be located and shown on plans as between reinforcement bars or WWF.

Use bevel plate at end bents only when the grade of the slab is 3.0% or more. Modify the roadway plate, the 5/8 in. vertical plate and the continuous bar when the bevel plate is required.

751.13.5.2 Plan of Beam at Bearings

PART PLAN AT BACK WALL
	TABLE FOR "R" - WIDE FLANGE BEAMS Nominal Flange Width (*) 8 ¼" 9" 10" 10 ½" 11 ½" 12" "R" 0.54" 0.54" 0.64" 0.70" 0.75" 0.80"
DETAIL "A" (TYPICAL)	(*) Note: For wide flange beams with flange widths other than those shown refer to AISC Steel Construction Manual for "R".
STRINGER OR GIRDER INTERMEDIATE BENTS	STRINGER OR GIRDER WITH BEARING AT END BENTS

(*) Note: Details for a steel structure shown, details for a prestressed structure similar.

751.13.5.3 Miscellaneous Details

TYPICAL SIDEWALK DETAILS

TYPICAL MEDIAN DETAILS

PART SECTION A-A

751.13.5.4 Flat Plate Expansion Devices - Details

Bridge Standard Drawings - Flat Plate Expansion Devices (DGN and PDF)
Standard Drawing Guidance may not be available on<br\>Bridge Standard Drawings (PDF) due to formatting.	All Bridge Standard Drawings (DGN and PDF)
Left Advance Bridges (PDF)
For Left Advance, P/S Structure at End Bent - CIP Slab
For Left Advance, P/S Structure at Int. Bent - CIP Slab
For Left Advance, Steel Structure at End Bent - CIP Slab
For Left Advance, Steel Structure at Int. Bent - CIP Slab
For Left Advance, P/S Structure at End Bent - PCP Slab
For Left Advance, P/S Structure at Int. Bent - PCP Slab
For Left Advance, Steel Structure at End Bent - PCP Slab
For Left Advance, Steel Structure at Int. Bent - PCP Slab
Right Advance Bridges (PDF)
For Right Advance, P/S Structure at End Bent - CIP Slab
For Right Advance, P/S Structure at Int. Bent - CIP Slab
For Right Advance, Steel Structure at End Bent - CIP Slab
For Right Advance, Steel Structure at Int. Bent - CIP Slab
For Right Advance, P/S Structure at End Bent - PCP Slab
For Right Advance, P/S Structure at Int. Bent - PCP Slab
For Right Advance, Steel Structure at End Bent - PCP Slab
For Right Advance, Steel Structure at Int. Bent - PCP Slab
Square Bridges (PDF)
For Square Advance, P/S Structure at End Bent - CIP Slab
For Square Advance, P/S Structure at Int. Bent - CIP Slab
For Square Advance, Steel Structure at End Bent - CIP Slab
For Square Advance, Steel Structure at Int. Bent - CIP Slab
For Square Advance, P/S Structure at End Bent - PCP Slab
For Square Advance, P/S Structure at Int. Bent - PCP Slab
For Square Advance, Steel Structure at End Bent - PCP Slab
For Square Advance, Steel Structure at Int. Bent - PCP Slab

751.13.6 Finger Plate Expansion Devices

751.13.6.1 General

The max. roadway surface gap (W) shall meet the following criteria:

When W(Long.) < 8", Then W(Tran.) < 3".

OR

When W(Long.) > 8", Then W(Tran.) < 2".

The min. finger overlap = 1.5"

Expansion lengths are calculated from the total movement value by the following equation:

Expansion length = $\,{\frac {Movement}{1.2\left(\alpha \right)\left(T\right)}}$

Where:

Max. Length of Expansion, ft. (1)		Total Movement, inches	Gap at 60° F, inches
Concrete	Steel
385	284	4	2 3/4
578	427	6	3 1/2
1 Longer expansion lengths are possible but they must be designed.

For Concrete:

$\,\alpha$ = 0.000006 ft/ft/˚F

$\,T$ = 120˚F

For Steel:

$\,\alpha$ = 0.0000065 ft/ft/˚F

$\,T$ = 150˚F

751.13.6.2 Details at Bents

Details of Fingers

Details at End Bent

Dimensions shown are perpendicular to centerline of joint and do not vary with skew (Unless otherwise noted).

PART SECTION THRU EXPANSION DEVICE
(Steel Structure)

	DETAIL "A"

PART SECTION THRU EXPANSION DEVICE
(Prestress Structure)

(*) Dimension along centerline of girder.

(**) When distance "A" or "D" shown in EPG 751.13.6.3 Typical Plan of Plate is greater than 9" or 12", respectively, then the details of supporting angles, mounting plates, shear studs and finger plate thickness need to be specially designed. Mounting Plates shall not be less than supporting angle in thickness.

Details at Intermediate Bent

Dimensions shown are perpendicular to centerline of joint and do not vary with skew (Unless otherwise noted).

PART SECTION THRU EXPANSION DEVICE
(Steel Structure)

Note: For Detail "A", see above.

PART SECTION THRU EXPANSION DEVICE
(Prestressed Structure)

(*) Dimension along centerline of Girder.

(**) When distance "A" or "D" shown in EPG 751.13.6.3 Typical Plan of Plate is greater than 9" or 12", respectively, then the details of supporting angles, mounting plates, shear studs and finger plate thickness need to be specially designed. Mounting Plates shall not be less than supporting angle in thickness.

Dimensions shown are perpendicular to centerline of joint and do not vary with skew (Unless otherwise noted).

(*) Dimension along centerline of Girder.

(**) When distance "A" or "D" shown is greater than 9" or 12", respectively, then the details of supporting angles, mounting plates, shear studs and finger plate thickness need to be specially designed. Mounting Plates shall not be less than supporting angle in thickness.

Details of W24 Piece

PLAN

ELEVATION OF PIECE W24 X	76 (SQUARED)
	104 (SKEWED)

Note:

Place the above details near "Part Section Thru Expansion Joint System For Finger Plates".

All holes shown for connections to be subpunched 11/16" Ø (shop or field drill) and reamed to 13/16" Ø in field.

751.13.6.3 Typical Plan of Plate

Squared Devices

A = 7.5" for 4" movement

A = 9.5" for 6" movement

C = A - 0.5" + Gap @ 60° F

Skewed Devices
	4" MOVEMENT $\theta$ A B 1° - 13° 7 1/2" 2 1/8" 14° - 19° 7 1/2" 2 3/16" 20° - 37° 7 1/2" 2 1/4" 38° - 46° 7" 2 5/16" 47° - 53° 6 1/2" 2 3/8" 54° - 58° 6" 2 7/16" 59° - 60° 5 1/2" 2 7/16"
	6" MOVEMENT $\theta$ A B 1° - 16° 9 1/2" 2 1/16" 17° - 29° 9 1/2" 2 1/8" 30° - 39° 9" 2 3/16" 40° - 48° 8 1/2" 2 1/4" 49° - 54° 7 1/2" 2 5/16" 55° - 60° 7" 2 3/8"

$\theta$ = skew angle

C = (A - 0.5") + (Gap @ 60°F) cos $\theta$

D = (A- 0.5") sec $\theta$

E = 4" - B

751.13.6.4 Slab Details

The slab extension beyond the edge of the supporting member shall be shown on the plan of slab.

Additional slab bars shall be located in the slab extensions.

Dimension F (Standard Details)   Structure End Bent Intermediate Bent Squared Bents Concrete A 0.25" + A/2 Steel 3.845" + A 4.095" + A/2 Skewed Bents Concrete (A)sec$\theta$ (0.25" + A/2)sec$\theta$ Steel (3.845" + A)sec$\theta$ (4.0925" + A/2)sec$\theta$

Where:

$\theta$ = skew angle

A = length of individual finder (previous section)

3.845" = ${\frac {(b_{f}-t_{w})}{2}}$ and 4.095" = ${\frac {(b_{f}-t_{w})}{2}}$ + 0.25"

b_f = 7.995", t_w = 0.305" (W14x43)

0.25" = 0.5" plate overhang divided by two

(The other overhang is included in Dimension A.)

On the plans the dimensions of the slab extension and the additional slab bars shall be specified on the plan of slab sheet where a special detail similar to the above detail may be used.

751.13.6.5 Barrier Curb Details

The R5 bar shall be used in the slab extension where there is insufficient clearance for the typical R4 bar.

The R5 bars shall be specified on the elevation of barrier sheet in a section detail.

PART ELEVATION OF BARRIER CURB (END BENT)	TYPICAL PART SECTION A-A
PART ELEVATION AT END OF BEVELED CURB BENT PLATE	SECTION C-C
PART ELEVATION OF BARRIER CURB (INTERMEDIATE BENT)	TYPICAL PART SECTION B-B

PART PLAN OF CURB AT END BENT (SQUARE)

PART PLAN OF CURB AT END BENT (SKEWED)

PART PLAN OF CURB AT INTERMEDIATE BENT (SQUARE)

PART PLAN OF CURB AT INTERMEDIATE BENT (SKEWED)

751.13.6.6 Median Barrier Curb Details

For the details not shown of median barrier bridge curb, see the safety barrier curb details. The Design Division Standard Plans (Concrete median barrier ), and the Bridge Design Layout.

TYPICAL PART SECTION A-A	TYPICAL PART SECTION B-B
	PART ELEVATION AT END OF BEVELED CURB BENT PLATE SECTION C-C
PART ELEVATION OF BARRIER CURB (INTERMEDIATE BENT)