Category:1004 Graded Aggregate for Bituminous Surface

From Engineering_Policy_Guide
Revision as of 15:04, 30 August 2010 by Smithk (talk | contribs) (added links)
Jump to navigation Jump to search
MGS Information
Current General Services Specifications (MGS) By Subject


This guidance establishes procedures for the inspection, testing and acceptance of graded aggregate for bituminous surface.

1004.1 Procedure

Inspection, testing, and sampling will be governed by the instructions contained in General Requirements for Material.

Field tests required are as follows:

Required Field Tests
TEST Template Template Description
Sieve Analysis T27 Sieve Analysis of Fine and Coarse Aggregate
Percent Deleterious SAA001Cx* NEWEST Deleterious 1004 Aggregate
*Test Template numbers have been depicted with a generic ‘x’ as some templates are updated and the last letter in the template name may change. The most current template for a template sequence should contain ‘NEWEST’ at the beginning of the template name.

1004.2 Acceptance

Acceptance is based on routine tests in the field to ensure compliance with Sec 1004. Samples are to be taken at destination or at the source of aggregate production by MoDOT inspectors at intervals of one per 1,500 tons.

1004.3 Records and Reports

All plant records shown in General Requirements for Material - Records and Reports shall be maintained. The aggregates shall be reported through SiteManager (SM) in accordance with Automation Section 3510.

1004.4 Laboratory Procedures for Sec 1004

1004.4.1 Types of Samples Tested

1004.4.1.1 Initial Approval Sample

Tests consist of specific gravity, absorption, and Los Angeles abrasion. The minimum time required for completion of tests is four working days from the date received. Test results and calculations shall be recorded through SM.

1004.4.1.2 Source Approval Sample

Tests consist of sieve analysis, specific gravity, absorption, Los Angeles abrasion, and deleterious content. The minimum time required for completion of tests is four working days from the date received. Test results and calculations shall be recorded through SM.

1004.4.1.3 Trial Mix Samples

Coarse aggregate tests for trial mix consist of sieve analysis, specific gravity, absorption, plastic index (when required), deleterious content, sand equivalency (T176), and uncompacted voids (T304). The minimum time required for completion of tests is four working days from the date received. Test results and calculations shall be recorded through SM.

Fine aggregate tests for trial mix consist of sieve analysis, specific gravity, plastic index (when required), other deleterious substances, clay lumps and shale, and lightweight particle content when specified. The minimum time required for completion of tests is four working days from the date received. Test results and calculations shall be recorded through SM.

1004.4.2 Procedure

1004.4.2.1 Sieve Analysis

Aggregate shall be tested in accordance with AASHTO T 27.

1004.4.2.2 Specific Gravity

Aggregate shall be tested in accordance with AASHTO T 85 for Bulk Specific Gravity.

1004.4.2.3 Absorption

Aggregate shall be tested in accordance with AASHTO T 85.

1004.4.2.4 Los Angeles Abrasion

Aggregates shall be tested in accordance with AASHTO T 96.

1004.4.2.5 Deleterious Content

The percentage of deleterious substances in coarse aggregate shall be determined according to MoDOT TM-71, Deleterious Content of Aggregate. Where field determinations show a total deleterious content of 2.5 percent or less, including not more than 0.5 percent shale, the deleterious content is to be inspected visually. The sample is to be tested if visual inspection indicates more than 2.5 percent deleterious material present in the sample. Source approval samples shall always be tested regardless of the content of deleterious material.

1004.4.3 Sample Record

The sample record shall be completed in SM, as described in Automation Section 3510, and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in Reporting Test Results, are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.