Category:132 Safety

From Engineering Policy Guide

Jump to: navigation, search
Safety Policies and Guidance
2012 USDOT Emergency Response Guide
Operations Safety Review Form
MSDS
Personal Protective Equipment (PPE):
High-Visibility Safety Apparel and Headwear
Fall Protection
Head and Eye Safety
Prescripton Safety Eyewear
Respiratory Protection
Safety Footwear
PPE Posters
Daytime Flagger
Daytime Worker
Nighttime Flagger
Nighttime Worker
11 x 17 ROW PPE
8.5 x 11 ROW PPE
Temporary Traffic Control
Technical Work Zone Form
Work Zone Inspection Forms
Work Zone Safety and Mobility Policy Resources
Work Zone Survey
Quality Standards for Temporary Traffic Control Devices
TMS
Safety Videos
Developing MoDOT's Safety Culture
Mowing Safety
Asphalt Operations
Chip Seal
Safety is My Story
2014 TMA Safety Points
Additional Information
Heat Safety
Bike and Pedestrian Safety
Hand Protection
Head and Eye/Face Protection
Hearing Protection
Incident Response Plan and Emergency Response Management
MoDOT's Safety Emphasis

Safety is one of MoDOT’s values. People often first think of work zones when they think of safety, but MoDOT addresses safety toward many audiences.

Missouri's Blueprint to Arrive Alive is an umbrella guide to increase coordination, communication and cooperation among state and local agencies, law enforcement, planning organizations, non-profit organizations and other safety advocates throughout the state.

Many hazards exist on a construction project and all personnel must be constantly alert to avoid injury. This article provides construction inspection guidelines for safety precautions.

Highway Safety Plan and Performance Plan describes how Missouri’s Section 402 State and Community Highway Safety Program grant will be used to promote highway safety within our state.

132.1 Material Inspection for Safety

MoDOT personnel are to practice the rules of safety at all times. Copies of the ”Safety Policies, Rules & Regulations Employee Handbook” are available in district offices, the Central Office and the Risk Management area of the intranet at http://lnapp1/RI/RIManual.NSF/SHToC?OpenView. These rules must be read and practiced. In addition to the information in the Handbook, the following paragraphs are more specific to situations that may be encountered in the process of inspecting and sampling materials.

Hard hats or other protective devices should be worn when conditions warrant and shall be worn when required by MoDOT policy. Loose clothes should not be worn around moving machinery. Extreme care must be taken when moving drilling equipment near power lines. In order to obtain a sample, it is sometimes necessary for the person taking the sample to be in a hazardous location and extreme caution should be exercised. Frequently, samples are taken in the vicinity of heavy equipment and the person taking the sample must know the equipment's operation for proper protection. The operator of the equipment should always be told when sampling is being started and when it is finished.

Sec 106 states "Facilities shall be furnished for the procurement of samples, performance of the tests and for the protection of testing equipment and supplies when tests are made at the source of production." Sec 106 further states, "The Commission will refuse to provide plant inspection at sources where adequate safety measures are not provided and maintained." Unsafe conditions shall be brought to the attention of the producer. If these conditions are not immediately corrected, the producer is to be notified in writing over the District Engineer's signature, of the specific unsafe condition and informed that plant inspection will not be provided until the condition has been corrected.

Some specific items to consider when sampling are:

(a) Make sure that ladders and scaffolding are adequate and secure.
(b) Keep away from unguarded moving parts.
(c) Allow no smoking or fire in the vicinity when handling volatiles.
(d) When sampling at asphalt plants, handle asphalt mixes carefully because of their high temperatures.
(e) When sampling from chutes, be careful that the weight of the material hitting the sample container does not cause a loss of balance.
(f) Goggles should be worn if there is danger of injury to the eye during sampling and/or testing. Particular care should be utilized when handling asphalt, cement, solvents and acids.
(g) Use respirators if an excessive amount of dust or fumes is present.
(h) Protective headgear shall be worn at all locations where the contractor or producer requires their employees to wear protective headgear.

The inspector shall at all times observe the safety code and rules in force at the plant or location where the inspection is to be performed. The most helpful safety rule to follow is common sense. No written instructions can cover all conditions that will be encountered. Therefore, safety is dependent to a great extent on personal care.





MoDOT addresses safety issues to many audiences
Personal tools