237.2 Title Sheet - Revision history

Smithk at 13:52, 30 April 2021

2021-04-30T13:52:08Z

← Older revision		Revision as of 08:52, 30 April 2021
Line 2:		Line 2:


	The title sheet identifies the set of plans, conveys the general type of improvement planned, and locates the improvement. Title sheet blanks are available on [[:Category:125 CADD Services\|CADD]] for district use. The first title sheet includes, at least, the information presented in EPG 237.2.1 through EPG 237.2.9. If additional title sheets are needed, only the title block information needs to be repeated. A note will be place in the lower right hand corner of the sheet stating Title Sheet 1 of 2.		The title sheet identifies the set of plans, conveys the general type of improvement planned, and locates the improvement. Title sheet blanks are available on [[:Category:125 CADD Services\|CADD]] for district use. The first title sheet includes, at least, the information presented in EPG 237.2.1 through EPG 237.2.9. If additional title sheets are needed, only the title block information needs to be repeated. A note will be place in the lower right hand corner of the sheet stating "Title Sheet 1 of 2".

	===237.2.1 Design Designation===		===237.2.1 Design Designation===

Smithk: /* 237.2.9 Utility Information Note */

2021-04-30T13:49:02Z

237.2.9 Utility Information Note

← Older revision		Revision as of 08:49, 30 April 2021
Line 61:		Line 61:

	The Utility Information Note may be placed on one of the plan and profile sheets.		The Utility Information Note may be placed on one of the plan and profile sheets.
	[[image:237.2.10.jpg\|right\|~~200px~~]]		[[image:237.2.10.jpg\|right\|175px]]

	===237.2.10 Key Map===		===237.2.10 Key Map===

Smithk: Per Bidding, provided guidance about multiple title pages.

2021-04-30T13:47:56Z

Per Bidding, provided guidance about multiple title pages.

← Older revision		Revision as of 08:47, 30 April 2021
Line 2:		Line 2:


	The title sheet identifies the set of plans, conveys the general type of improvement planned, and locates the improvement. Title sheet blanks are available on [[:Category:125 CADD Services\|CADD]] for district use. The title sheet includes, at least, the ~~following~~ information:		The title sheet identifies the set of plans, conveys the general type of improvement planned, and locates the improvement. Title sheet blanks are available on [[:Category:125 CADD Services\|CADD]] for district use. The first title sheet includes, at least, the information presented in EPG 237.2.1 through EPG 237.2.9. If additional title sheets are needed, only the title block information needs to be repeated. A note will be place in the lower right hand corner of the sheet stating Title Sheet 1 of 2.

	===237.2.1 Design Designation===		===237.2.1 Design Designation===
Line 39:		Line 39:
	===237.2.5 Title Block===		===237.2.5 Title Block===

	The title block is filled out by the district, with the exception of the project number. Design ~~adds this number~~ when necessary.		The title block is filled out by the district, with the exception of the contract ID and project number. Central Office Design will provide these numbers when necessary. The information in the title block will be same on all the sheets in the job number.

	===237.2.6 Index of Sheets===		===237.2.6 Index of Sheets===

	A complete index of the sheets in the plans is shown on the title sheet. Design adds the number of sheets for bridge plans ~~and the standard plans index. This index is completed in [[:Category:125 CADD Services\|CADD]]~~.		A complete index of the sheets in the plans is shown on the title sheet and should be included on the first title page. District Design adds the number of sheets for bridge plans.

	===237.2.7 Length of Project===		===237.2.7 Length of Project===
Line 56:		Line 56:
	===237.2.9 Utility Information Note===		===237.2.9 Utility Information Note===

	The following note is ~~required to be~~ placed on the title sheet to inform contractors of the suitability of the utility information contained on the plans.		The following note is normally placed on the title sheet to inform contractors of the suitability of the utility information contained on the plans.

			:''"The existence and approximate location of utility facilities known to exist, as shown on the plans, are based on the best information available to the Commission at this time. This information is provided by the Commission "as-is" and the Commission expressly disclaims any representation or warranty as to the completeness, accuracy, or suitability of the information for any use. Reliance upon this information is done at the risk and peril of the user, and the Commission shall not be liable for any damages that may arise from any error in the information. It is, therefore, the responsibility of the contractor to verify the existence, location and status of any facility. Such verification includes direct contact with the listed utilities"''.

			The Utility Information Note may be placed on one of the plan and profile sheets.
			[[image:237.2.10.jpg\|right\|200px]]
			===237.2.10 Key Map===

			Some districts show the location of the county where the work will be performed. This is an option and not required on the title sheet.

	:''"The existence and approximate location of utility facilities known to exist, as shown on the plans, are based on the best information available to the Commission at this time. This information is provided by the Commission "as-is" and the Commission expressly disclaims any representation or warranty as to the completeness, accuracy, or suitability of the information for any use. Reliance upon this information is done at the risk and peril of the user, and the Commission shall not be liable for any damages that may arise from any error in the information. It is, therefore, the responsibility of the contractor to verify the existence, location and status of any facility. Such verification includes direct contact with the listed utilities"''.

	[[category:237 Contract Plans\|237.02]]		[[category:237 Contract Plans\|237.02]]

Smithk: Per Env'l, updated MoDOT's SWPPP as well as supporting guidance due to issuance of MoDOT's new State Operating Permit from DNR.

2020-01-10T15:29:25Z

Per Env'l, updated MoDOT's SWPPP as well as supporting guidance due to issuance of MoDOT's new State Operating Permit from DNR.

← Older revision		Revision as of 10:29, 10 January 2020
Line 48:		Line 48:

	The length of project is the total length of the improvement less equations and exceptions as noted in the plans. Examples of common exceptions are existing surfaces to be left in place, existing bridges to be used in place, existing intersections, and railroad grade crossings where the exception is the distance between the ends of railroad crossties.		The length of project is the total length of the improvement less equations and exceptions as noted in the plans. Examples of common exceptions are existing surfaces to be left in place, existing bridges to be used in place, existing intersections, and railroad grade crossings where the exception is the distance between the ends of railroad crossties.
			[[image:237.2.8 2020.jpg\|right\|375px]]

	===237.2.8 Utility Information Note===		===237.2.8 Estimated Area of Disturbance===

			The estimated area of disturbance is shown on the title sheet as a reference for bidders to determine if additional land disturbance permits are necessary for off-site borrow areas, waste disposal areas, staging areas etc. based on the common plan concept with MoDOT's permitted site.

			===237.2.9 Utility Information Note===

	The following note is required to be placed on the title sheet to inform contractors of the suitability of the utility information contained on the plans.		The following note is required to be placed on the title sheet to inform contractors of the suitability of the utility information contained on the plans.

Smithk: /* 237.2.8 Utility Information Note */Per DE, relocated specifications to more reasonable locations

2016-09-23T14:50:30Z

237.2.8 Utility Information Note: Per DE, relocated specifications to more reasonable locations

← Older revision		Revision as of 09:50, 23 September 2016
Line 53:		Line 53:
	The following note is required to be placed on the title sheet to inform contractors of the suitability of the utility information contained on the plans.		The following note is required to be placed on the title sheet to inform contractors of the suitability of the utility information contained on the plans.

	:''"The existence and approximate location of utility facilities known to exist, as shown on the plans, are based on the best information available to the Commission at this time. This information is provided by the Commission "as-is" and the Commission expressly disclaims any representation or warranty as to the completeness, accuracy, or suitability of the information for any use. Reliance upon this information is done at the risk and peril of the user, and the Commission shall not be liable for any damages that may arise from any error in the information''".		:''"The existence and approximate location of utility facilities known to exist, as shown on the plans, are based on the best information available to the Commission at this time. This information is provided by the Commission "as-is" and the Commission expressly disclaims any representation or warranty as to the completeness, accuracy, or suitability of the information for any use. Reliance upon this information is done at the risk and peril of the user, and the Commission shall not be liable for any damages that may arise from any error in the information. It is, therefore, the responsibility of the contractor to verify the existence, location and status of any facility. Such verification includes direct contact with the listed utilities"''.

	[[category:237 Contract Plans\|237.02]]		[[category:237 Contract Plans\|237.02]]

Smithk: added link

2014-07-17T17:15:18Z

added link

← Older revision		Revision as of 12:15, 17 July 2014
Line 9:		Line 9:

	:(1) [http://www.modot.org/newsandinfo/functionalclassificationmaps/index.htm functional classification],		:(1) [http://www.modot.org/newsandinfo/functionalclassificationmaps/index.htm functional classification],
	:(2) present daily traffic volume, AADT,		:(2) present [http://modot.org/safety/documents/2013_Traffic_Statewide.pdf daily traffic volume], AADT,
	:(3) a projected traffic volume, AADT,		:(3) a projected traffic volume, AADT,
	:(4) design hourly volume percentage, DHV,		:(4) design hourly volume percentage, DHV,

Smithk: /* 237.2.1 Design Designation */ added link

2013-08-12T15:41:39Z

237.2.1 Design Designation: added link

← Older revision		Revision as of 10:41, 12 August 2013
Line 8:		Line 8:
	The major criteria under which the improvement is designed are included on the title sheet. These criteria are determined in the appropriate [[:Category:128 Conceptual Studies\|conceptual study report]], in the [[:Category:126 Location Study and Alternatives Analysis\|location study/environmental report]], or during design of the project. The design designation consists of:		The major criteria under which the improvement is designed are included on the title sheet. These criteria are determined in the appropriate [[:Category:128 Conceptual Studies\|conceptual study report]], in the [[:Category:126 Location Study and Alternatives Analysis\|location study/environmental report]], or during design of the project. The design designation consists of:

	:(1) functional classification,		:(1) [http://www.modot.org/newsandinfo/functionalclassificationmaps/index.htm functional classification],
	:(2) present daily traffic volume, AADT,		:(2) present daily traffic volume, AADT,
	:(3) a projected traffic volume, AADT,		:(3) a projected traffic volume, AADT,

Smithk: /* 237.2.4 Location Sketch */ updated link

2010-08-03T20:19:16Z

237.2.4 Location Sketch: updated link

← Older revision		Revision as of 15:19, 3 August 2010
Line 35:		Line 35:
	===237.2.4 Location Sketch===		===237.2.4 Location Sketch===

	The sketch showing the location and limits of the improvement is added to the title sheet by the district. The location sketch shows physical features that will aid in the identification of the proposed road location, including intersecting and adjacent roads, prominent landmarks, towns, section lines, section numbers, and a north arrow. The delineation of the proposed roadway is to be adequate to allow visual identification of its features, such as whether it’s dual or single lane, location of [[Outer Roads and Service Roads\|outer roadways]], bridges, interchanges, ramps, etc. The major items of work are noted. The project’s beginning and ending points are identified by station and log mile, along with any stationing equations, exceptions, or reverse points. The USGS 7.5 minute series topographic maps may be used as a base from which to develop the location sketch. A graphic scale is included for the location sketch so the scale will be applicable on reduced size prints.		The sketch showing the location and limits of the improvement is added to the title sheet by the district. The location sketch shows physical features that will aid in the identification of the proposed road location, including intersecting and adjacent roads, prominent landmarks, towns, section lines, section numbers, and a north arrow. The delineation of the proposed roadway is to be adequate to allow visual identification of its features, such as whether it’s dual or single lane, location of [[232.5 Freeways#Outer Roads and Service Roads\|outer roadways]], bridges, interchanges, ramps, etc. The major items of work are noted. The project’s beginning and ending points are identified by station and log mile, along with any stationing equations, exceptions, or reverse points. The USGS 7.5 minute series topographic maps may be used as a base from which to develop the location sketch. A graphic scale is included for the location sketch so the scale will be applicable on reduced size prints.

	===237.2.5 Title Block===		===237.2.5 Title Block===

EPG-Admin: add "Utility Infromation Note"

2009-06-04T13:20:28Z

add "Utility Infromation Note"

← Older revision		Revision as of 08:20, 4 June 2009
Line 48:		Line 48:

	The length of project is the total length of the improvement less equations and exceptions as noted in the plans. Examples of common exceptions are existing surfaces to be left in place, existing bridges to be used in place, existing intersections, and railroad grade crossings where the exception is the distance between the ends of railroad crossties.		The length of project is the total length of the improvement less equations and exceptions as noted in the plans. Examples of common exceptions are existing surfaces to be left in place, existing bridges to be used in place, existing intersections, and railroad grade crossings where the exception is the distance between the ends of railroad crossties.

			===237.2.8 Utility Information Note===

			The following note is required to be placed on the title sheet to inform contractors of the suitability of the utility information contained on the plans.

			:''"The existence and approximate location of utility facilities known to exist, as shown on the plans, are based on the best information available to the Commission at this time. This information is provided by the Commission "as-is" and the Commission expressly disclaims any representation or warranty as to the completeness, accuracy, or suitability of the information for any use. Reliance upon this information is done at the risk and peril of the user, and the Commission shall not be liable for any damages that may arise from any error in the information''".

	[[category:237 Contract Plans\|237.02]]		[[category:237 Contract Plans\|237.02]]

EPG-Admin: add links to "conceptual study" and "location study"

2008-10-08T16:23:17Z

add links to "conceptual study" and "location study"

← Older revision		Revision as of 11:23, 8 October 2008
Line 6:		Line 6:
	===237.2.1 Design Designation===		===237.2.1 Design Designation===

	The major criteria under which the improvement is designed are included on the title sheet. These criteria are determined in the appropriate ~~conceptual study report (refer to~~ [[:Category:128 Conceptual Studies\|~~Conceptual Study~~]]), in the location study/environmental report ~~(refer to 128, Conceptual Study)~~, or during design of the project. The design designation consists of:		The major criteria under which the improvement is designed are included on the title sheet. These criteria are determined in the appropriate [[:Category:128 Conceptual Studies\|conceptual study report]], in the [[:Category:126 Location Study and Alternatives Analysis\|location study/environmental report]], or during design of the project. The design designation consists of:

	:(1) functional classification,		:(1) functional classification,