Category:1108 Blades Maintainer and Loader - Revision history

Hoskir: /* 1108.4.1 Procedure */

2025-01-08T19:44:22Z

1108.4.1 Procedure

← Older revision		Revision as of 14:44, 8 January 2025
Line 39:		Line 39:
	This article establishes procedures for Laboratory testing and reporting samples of maintainer and loader blades. The material specification requirements are set forth in the bid request issued by MoDOT.		This article establishes procedures for Laboratory testing and reporting samples of maintainer and loader blades. The material specification requirements are set forth in the bid request issued by MoDOT.

	===1108.4.1 Procedure===		===1108.4.1 Procedure===
	Tests consist of examination of punchings and dimensions, distortion, weight (mass), hardness and chemical analysis.		Tests consist of examination of punchings and dimensions, distortion, weight (mass), hardness and chemical analysis.

Hoskir: /* 1108.4.1 Procedure */ updated formatting

2025-01-08T19:44:13Z

1108.4.1 Procedure: updated formatting

← Older revision		Revision as of 14:44, 8 January 2025
Line 48:		Line 48:
	Comply with the requirements specified in the bid request. Tests shall be performed according to ASTM E30-68 exclusive of any later revisions hereto using the following methods:		Comply with the requirements specified in the bid request. Tests shall be performed according to ASTM E30-68 exclusive of any later revisions hereto using the following methods:

	:Carbon: Direct Combustion Method		: Carbon: Direct Combustion Method
			: Manganese: [[106.3.2.57 TM-57, Determination of Manganese and/or Copper in Steel\|EPG 106.3.2.57 TM-57, Determination of Manganese and/or Copper in Steel]]
	:Manganese: [[106.3.2.57 TM-57, Determination of Manganese and/or Copper in Steel\|EPG 106.3.2.57 TM-57, Determination of Manganese and/or Copper in Steel]]		: Phosphorus: Alkalimetric Method
			: Sulfur: Evolution Method
	:Phosphorus: Alkalimetric Method		: Silicon: Sulfuric Acid Method

	:Sulfur: Evolution Method

	:Silicon: Sulfuric Acid Method

	Original chemical test data and calculations shall be recorded in Laboratory workbooks. Physical and chemical test results shall be recorded through AWP.		Original chemical test data and calculations shall be recorded in Laboratory workbooks. Physical and chemical test results shall be recorded through AWP.

Hoskir: /* 1108.1 Apparatus */ updated formatting

2025-01-08T19:43:43Z

1108.1 Apparatus: updated formatting

← Older revision		Revision as of 14:43, 8 January 2025
Line 12:		Line 12:

	==1108.1 Apparatus==		==1108.1 Apparatus==
	:a) Rule with suitable graduations to accurately measure the material to be inspected.		: a) Rule with suitable graduations to accurately measure the material to be inspected.
			: b) Balance or scale accurate to within 0.5 percent of the weight (mass) of the sample to be weighed.
	:b) Balance or scale accurate to within 0.5 percent of the weight (mass) of the sample to be weighed.

	===1108.2 Procedure===		===1108.2 Procedure===

Hoskir: updated formatting and links

2025-01-08T19:16:30Z

updated formatting and links

← Older revision		Revision as of 14:16, 8 January 2025
Line 1:		Line 1:
	{\|style="~~padding~~: ~~0.3em~~; margin-left:~~1px~~; border:2px solid ~~#a9a9a9~~; ~~text~~-~~align~~:~~center~~; ~~font~~-~~size: 95%; background~~:#~~f5f5f5" width="280px" align="right~~"		</br>
	\|-
	\|'''MGS Information'''		<div style="float: right; margin-top: 5px; margin-left: 30px; margin-bottom: 30px;">__TOC__</div>
	\|-
	\|[https://www.modot.org/general-services-specifications-mgs-subject Current General Services Specifications (MGS) By Subject]		<div style="width: 250px; margin-top: 8px; margin-bottom: 8px; padding: 18px; border: 2px solid black; border-radius:5px; box-shadow:5px 5px 5px #888888">
	\|}		'''<u><center>MGS Information</center></u>'''
			<center>[https://www.modot.org/general-services-specifications-mgs-subject Current General Services Specifications (MGS) By Subject]</center>
			</div>


	This article establishes the procedures for inspecting, [[106.3 Samples, Tests and Cited Specifications#106.3.1 Sampling\|sampling]] and reporting maintainer and loader blades. The material specification requirements are set forth in a bid request issued by MoDOT.		This article establishes the procedures for inspecting, [[106.3 Samples, Tests and Cited Specifications#106.3.1 Sampling\|sampling]] and reporting maintainer and loader blades. The material specification requirements are set forth in a bid request issued by MoDOT.

	==1108.1 Apparatus==		==1108.1 Apparatus==
			:a) Rule with suitable graduations to accurately measure the material to be inspected.

	~~a) Rule with suitable graduations to accurately measure the material to be inspected.~~		:b) Balance or scale accurate to within 0.5 percent of the weight (mass) of the sample to be weighed.

	b) Balance or scale accurate to within 0.5 percent of the weight (mass) of the sample to be weighed.

	===1108.2 Procedure===		===1108.2 Procedure===
	Upon award of the contract for furnishing maintainer and loader blades, the Division		Upon award of the contract for furnishing maintainer and loader blades, the Division Engineer, Construction and Materials, will determine the number and types of samples required for testing in the Laboratory. This determination will be made considering all blades on a statewide basis. The district(s) responsible for sampling will be notified by letter with a copy to all districts which are to receive blades.
	Engineer, Construction and Materials, will determine the number and types of samples required for testing in the Laboratory. This determination will be made considering all blades on a statewide basis. The district(s) responsible for sampling will be notified by letter with a copy to all districts which are to receive blades.

	===1108.2.1 Inspection===		===1108.2.1 Inspection===
Line 33:		Line 34:
	If field inspection and Laboratory testing shows noncompliance with specification requirements, the AASHTOWARE Project (AWP) record shall be completed indicating that the material is rejected and the reasons for rejection shall be listed in the report.		If field inspection and Laboratory testing shows noncompliance with specification requirements, the AASHTOWARE Project (AWP) record shall be completed indicating that the material is rejected and the reasons for rejection shall be listed in the report.

	If field inspection and Laboratory testing shows compliance with specification requirements the AASHTOWARE Project (AWP) record shall be completed indicating that the material is accepted. The record should include the statements that a satisfactory manufacturer's certification is on file and field inspection was satisfactory.		If field inspection and Laboratory testing shows compliance with specification requirements the AASHTOWARE Project (AWP) record shall be completed indicating that the material is accepted. The record should include the statements that a satisfactory manufacturer's certification is on file and field inspection was satisfactory.

	==1108.4 Laboratory Testing Guidelines==		==1108.4 Laboratory Testing Guidelines==

	This article establishes procedures for Laboratory testing and reporting samples of maintainer and loader blades. The material specification requirements are set forth in the bid request issued by MoDOT.		This article establishes procedures for Laboratory testing and reporting samples of maintainer and loader blades. The material specification requirements are set forth in the bid request issued by MoDOT.

	===1108.4.1 Procedure===		===1108.4.1 Procedure===
Line 46:		Line 47:
	Brinell hardness tests shall comply with the requirements specified in the bid request and shall be conducted in accordance with AASHTO T70.		Brinell hardness tests shall comply with the requirements specified in the bid request and shall be conducted in accordance with AASHTO T70.

	Comply with the requirements specified in the bid request. Tests shall be performed according to ASTM E30-68 exclusive of any later revisions hereto using the following methods:		Comply with the requirements specified in the bid request. Tests shall be performed according to ASTM E30-68 exclusive of any later revisions hereto using the following methods:

	::Carbon: Direct Combustion Method		:Carbon: Direct Combustion Method

	::Manganese: [[106.3.2.57 TM-57, Determination of Manganese and/or Copper in Steel\|EPG 106.3.2.57 TM-57, Determination of Manganese and/or Copper in Steel]]		:Manganese: [[106.3.2.57 TM-57, Determination of Manganese and/or Copper in Steel\|EPG 106.3.2.57 TM-57, Determination of Manganese and/or Copper in Steel]]

	::Phosphorus: Alkalimetric Method		:Phosphorus: Alkalimetric Method

	::Sulfur: Evolution Method		:Sulfur: Evolution Method

	::Silicon: Sulfuric Acid Method		:Silicon: Sulfuric Acid Method

	Original chemical test data and calculations shall be recorded in Laboratory workbooks. Physical and chemical test results shall be recorded through AWP.		Original chemical test data and calculations shall be recorded in Laboratory workbooks. Physical and chemical test results shall be recorded through AWP.
Line 63:		Line 64:

	===1108.4.2 Sample Record===		===1108.4.2 Sample Record===
	The sample record shall be completed in AASHTOWARE Project (AWP) in accordance with [[:~~Category:101 Standard Forms #Sample Record, General\|~~AWP MA Sample Record, General]], and shall indicate ~~acceptanceor~~ rejection based on district reported results and laboratory determined results. Final acceptance is determined by the district, based on lab tests and physical inspection. Rejection may be by lab or district, depending on where the non-conformance is. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.		The sample record shall be completed in AASHTOWARE Project (AWP) in accordance with [https://epg.modot.org/forms/CM/AWP_MA_Sample_Record_General.docx AWP MA Sample Record, General]], and shall indicate acceptance or rejection based on district reported results and laboratory determined results. Final acceptance is determined by the district, based on lab tests and physical inspection. Rejection may be by lab or district, depending on where the non-conformance is. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.

			[[Category:1100_MAINTENANCE_MATERIALS]]

Smithk: Per CM, removed archaic SiteManager info and replaced with AASHTOWARE info

2021-10-19T16:17:04Z

Per CM, removed archaic SiteManager info and replaced with AASHTOWARE info

← Older revision		Revision as of 11:17, 19 October 2021
Line 33:		Line 33:
	If field inspection and Laboratory testing shows noncompliance with specification requirements, the AASHTOWARE Project (AWP) record shall be completed indicating that the material is rejected and the reasons for rejection shall be listed in the report.		If field inspection and Laboratory testing shows noncompliance with specification requirements, the AASHTOWARE Project (AWP) record shall be completed indicating that the material is rejected and the reasons for rejection shall be listed in the report.

	If field inspection and Laboratory testing shows compliance with specification requirements the SM record shall be completed indicating that the material is accepted. The record should include the statements that a satisfactory manufacturer's certification is on file and field inspection was satisfactory.		If field inspection and Laboratory testing shows compliance with specification requirements the AASHTOWARE Project (AWP) record shall be completed indicating that the material is accepted. The record should include the statements that a satisfactory manufacturer's certification is on file and field inspection was satisfactory.

	==1108.4 Laboratory Testing Guidelines==		==1108.4 Laboratory Testing Guidelines==
Line 58:		Line 58:
	::Silicon: Sulfuric Acid Method		::Silicon: Sulfuric Acid Method

	Original chemical test data and calculations shall be recorded in Laboratory workbooks. Physical and chemical test results shall be recorded through SM.		Original chemical test data and calculations shall be recorded in Laboratory workbooks. Physical and chemical test results shall be recorded through AWP.

	Manufacturer's certification, as required in the bid request for maintainer and loader blades, shall be checked for specification compliance.		Manufacturer's certification, as required in the bid request for maintainer and loader blades, shall be checked for specification compliance.

Smithk: Per CM, removed archaic SiteManager info and replaced with AASHTOWARE info

2021-09-17T12:58:16Z

Per CM, removed archaic SiteManager info and replaced with AASHTOWARE info

← Older revision		Revision as of 07:58, 17 September 2021
Line 31:		Line 31:

	==1108.3 Report==		==1108.3 Report==
	If field inspection and Laboratory testing shows noncompliance with specification requirements, the ~~[http://wwwi/intranet/cm/siteManager.htm SiteManager~~ (SM)] record shall be completed indicating that the material is rejected and the reasons for rejection shall be listed in the report.		If field inspection and Laboratory testing shows noncompliance with specification requirements, the AASHTOWARE Project (AWP) record shall be completed indicating that the material is rejected and the reasons for rejection shall be listed in the report.

	If field inspection and Laboratory testing shows compliance with specification requirements the SM record shall be completed indicating that the material is accepted. The record should include the statements that a satisfactory manufacturer's certification is on file and field inspection was satisfactory.		If field inspection and Laboratory testing shows compliance with specification requirements the SM record shall be completed indicating that the material is accepted. The record should include the statements that a satisfactory manufacturer's certification is on file and field inspection was satisfactory.
Line 63:		Line 63:

	===1108.4.2 Sample Record===		===1108.4.2 Sample Record===
	The sample record shall be completed in ~~SM, as described~~ in [[:Category:101 Standard Forms#Sample Record General ~~Information~~\| Sample Record General ~~Information]] [[image:bulldozer.jpg\|20px~~]], and shall indicate acceptanceor rejection based on district reported results and laboratory determined results. Final acceptance is determined by the district, based on lab tests and physical inspection. Rejection may be by lab or district, depending on where the non-conformance is. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.		The sample record shall be completed in AASHTOWARE Project (AWP) in accordance with [[:Category:101 Standard Forms #Sample Record, General\|AWP MA Sample Record, General]], and shall indicate acceptanceor rejection based on district reported results and laboratory determined results. Final acceptance is determined by the district, based on lab tests and physical inspection. Rejection may be by lab or district, depending on where the non-conformance is. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.

Smithk: updated link

2018-10-16T13:10:03Z

updated link

← Older revision		Revision as of 08:10, 16 October 2018
Line 3:		Line 3:
	\|'''MGS Information'''		\|'''MGS Information'''
	\|-		\|-
	\|[~~http~~://www.modot.~~mo.gov/business/materials/pdf~~/mgs~~/MGSINDEX.pdf~~ Current General Services Specifications (MGS) By Subject]		\|[https://www.modot.org/general-services-specifications-mgs-subject Current General Services Specifications (MGS) By Subject]
	\|}		\|}

Smithk: updated link

2013-08-22T13:58:13Z

updated link

← Older revision		Revision as of 08:58, 22 August 2013
Line 63:		Line 63:

	===1108.4.2 Sample Record===		===1108.4.2 Sample Record===
	The sample record shall be completed in SM, as described in [~~http~~:~~//contribute.modot.mo.gov/business/materials/pdf/vol_3/AS3510~~.~~pdf Automation Section 3510~~], and shall indicate acceptanceor rejection based on district reported results and laboratory determined results. Final acceptance is determined by the district, based on lab tests and physical inspection. Rejection may be by lab or district, depending on where the non-conformance is. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.		The sample record shall be completed in SM, as described in [[:Category:101 Standard Forms#Sample Record General Information\| Sample Record General Information]] [[image:bulldozer.jpg\|20px]], and shall indicate acceptanceor rejection based on district reported results and laboratory determined results. Final acceptance is determined by the district, based on lab tests and physical inspection. Rejection may be by lab or district, depending on where the non-conformance is. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.

Smithk: /* 1108.4.2 Sample Record */ Per CM, updated link to AS 3510

2011-07-05T20:32:49Z

1108.4.2 Sample Record: Per CM, updated link to AS 3510

← Older revision		Revision as of 15:32, 5 July 2011
Line 63:		Line 63:

	===1108.4.2 Sample Record===		===1108.4.2 Sample Record===
	The sample record shall be completed in SM, as described in [http://~~wwwi~~/~~intranet~~/cm/~~materials~~/vol_3/AS3510.pdf Automation Section 3510], and shall indicate acceptanceor rejection based on district reported results and laboratory determined results. Final acceptance is determined by the district, based on lab tests and physical inspection. Rejection may be by lab or district, depending on where the non-conformance is. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.		The sample record shall be completed in SM, as described in [http://contribute.modot.mo.gov/business/materials/pdf/vol_3/AS3510.pdf Automation Section 3510], and shall indicate acceptanceor rejection based on district reported results and laboratory determined results. Final acceptance is determined by the district, based on lab tests and physical inspection. Rejection may be by lab or district, depending on where the non-conformance is. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.

Smithk: added link

2010-08-30T20:20:15Z

added link

← Older revision		Revision as of 15:20, 30 August 2010
Line 31:		Line 31:

	==1108.3 Report==		==1108.3 Report==
	If field inspection and Laboratory testing shows noncompliance with specification requirements, the SiteManager record shall be completed indicating that the material is rejected and the reasons for rejection shall be listed in the report.		If field inspection and Laboratory testing shows noncompliance with specification requirements, the [http://wwwi/intranet/cm/siteManager.htm SiteManager (SM)] record shall be completed indicating that the material is rejected and the reasons for rejection shall be listed in the report.

	If field inspection and Laboratory testing shows compliance with specification requirements the ~~SiteManager~~ record shall be completed indicating that the material is accepted. The record should include the statements that a satisfactory manufacturer's certification is on file and field inspection was satisfactory.		If field inspection and Laboratory testing shows compliance with specification requirements the SM record shall be completed indicating that the material is accepted. The record should include the statements that a satisfactory manufacturer's certification is on file and field inspection was satisfactory.

	==1108.4 Laboratory Testing Guidelines==		==1108.4 Laboratory Testing Guidelines==
Line 58:		Line 58:
	::Silicon: Sulfuric Acid Method		::Silicon: Sulfuric Acid Method

	Original chemical test data and calculations shall be recorded in Laboratory workbooks. Physical and chemical test results shall be recorded through ~~SiteManager~~.		Original chemical test data and calculations shall be recorded in Laboratory workbooks. Physical and chemical test results shall be recorded through SM.

	Manufacturer's certification, as required in the bid request for maintainer and loader blades, shall be checked for specification compliance.		Manufacturer's certification, as required in the bid request for maintainer and loader blades, shall be checked for specification compliance.

	===1108.4.2 Sample Record===		===1108.4.2 Sample Record===
	The sample record shall be completed in ~~SiteManager~~, as described in [http://wwwi/intranet/cm/materials/vol_3/AS3510.pdf Automation Section 3510], and shall indicate acceptanceor rejection based on district reported results and laboratory determined results. Final acceptance is determined by the district, based on lab tests and physical inspection. Rejection may be by lab or district, depending on where the non-conformance is. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.		The sample record shall be completed in SM, as described in [http://wwwi/intranet/cm/materials/vol_3/AS3510.pdf Automation Section 3510], and shall indicate acceptanceor rejection based on district reported results and laboratory determined results. Final acceptance is determined by the district, based on lab tests and physical inspection. Rejection may be by lab or district, depending on where the non-conformance is. Appropriate remarks, as described in [[106.20 Reporting\|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.