Difference between revisions of "901.18 Laboratory Testing for Sec 901"
m (updated link) |
m (Per TS, numerous minor clarifications) |
||
| Line 1: | Line 1: | ||
| − | This article establishes procedures for testing and reporting Laboratory samples of bolts, nuts, washers and polyurethane foam used in highway lighting. Refer to [http://www.modot.org/business/standards_and_specs/SpecbookEPG.pdf#page=13 Sec 901] for MoDOT’s specifications. | + | This article establishes procedures for testing and reporting Laboratory samples of bolts, nuts, washers, and polyurethane foam used in highway lighting. Refer to [http://www.modot.org/business/standards_and_specs/SpecbookEPG.pdf#page=13 Sec 901] for MoDOT’s specifications. |
| Line 6: | Line 6: | ||
===Bolts, Nuts, and Washers=== | ===Bolts, Nuts, and Washers=== | ||
| − | Chemical tests consisting of mass of coating | + | Chemical tests consisting of mass of coating shall be determined according to AASHTO M232. Original test data and calculations shall be recorded in Laboratory workbooks. Test results shall then be recorded through AASHTOWare. |
| − | Physical tests shall be conducted according to [[:Category:712 Structural Steel Construction#712.3.2.2 Physical Tests - Bolts and Nuts|EPG 712.3.2.2 Physical Tests - Bolts and Nuts]]. Test results and calculations shall be recorded through | + | Physical tests shall be conducted according to [[:Category:712 Structural Steel Construction#712.3.2.2 Physical Tests - Bolts and Nuts|EPG 712.3.2.2 Physical Tests - Bolts and Nuts]]. Test results and calculations shall be recorded through AASHTOWare. |
===Polyurethane Foam=== | ===Polyurethane Foam=== | ||
| Line 18: | Line 18: | ||
:(b) Density - ASTM D1622 | :(b) Density - ASTM D1622 | ||
| − | Test results and calculations shall be recorded through | + | Test results and calculations shall be recorded through AASHTOWare. |
==901.18.2 Sample Record== | ==901.18.2 Sample Record== | ||
| − | The sample record shall be completed in | + | The sample record shall be completed in AASHTOWare, as described in [[:Category:101 Standard Forms#Sample Record General Information| Sample Record General Information]] [[image:bulldozer.jpg|20px]], and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in [http://epg.modot.org/index.php/106.20_Reporting EPG 106.20 Reporting], are to be included in the report to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab. |
[[Category:901 Lighting]] | [[Category:901 Lighting]] | ||
Revision as of 13:30, 18 August 2020
This article establishes procedures for testing and reporting Laboratory samples of bolts, nuts, washers, and polyurethane foam used in highway lighting. Refer to Sec 901 for MoDOT’s specifications.
Contents
901.18.1 Procedure
Bolts, Nuts, and Washers
Chemical tests consisting of mass of coating shall be determined according to AASHTO M232. Original test data and calculations shall be recorded in Laboratory workbooks. Test results shall then be recorded through AASHTOWare.
Physical tests shall be conducted according to EPG 712.3.2.2 Physical Tests - Bolts and Nuts. Test results and calculations shall be recorded through AASHTOWare.
Polyurethane Foam
Tests on samples of polyurethane foam shall be conducted in accordance with the following methods:
- (a) Compressive Strength - ASTM D1621
- (b) Density - ASTM D1622
Test results and calculations shall be recorded through AASHTOWare.
901.18.2 Sample Record
The sample record shall be completed in AASHTOWare, as described in Sample Record General Information 
, and shall indicate acceptance, qualified acceptance or rejection. Appropriate remarks, as described in EPG 106.20 Reporting, are to be included in the report to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.
