Difference between revisions of "771.19 Chip Seal to Entire Deck"

From Engineering_Policy_Guide
Jump to navigation Jump to search
(Added Links to Innovation Library.)
m
 
(6 intermediate revisions by 2 users not shown)
Line 1: Line 1:
−
{|style="padding: 0.3em; margin-left:15px; border:1px solid #a9a9a9; text-align:center; font-size: 95%; background:#f5f5f5" width="160px" align="right"
 
−
|- 
 
−
|'''Code:''' R322
 
−
|}
 
−
 
−
Chip seals help to seal bridge decks with excessive cracking to prevent intrusion of water and chlorides into the bridge deck. The work should be performed in July and August.
 
−
 
−
==Materials==
 
 
{|style="padding: 0.3em; margin-left:15px; border:1px solid #a9a9a9; text-align:center; font-size: 95%; background:#ffddcc" width="210px" align="right"  
 
{|style="padding: 0.3em; margin-left:15px; border:1px solid #a9a9a9; text-align:center; font-size: 95%; background:#ffddcc" width="210px" align="right"  
 
|-
 
|-
 
|'''Bridge Deck, Sealer'''
 
|'''Bridge Deck, Sealer'''
 
|-
 
|-
−
|[http://library.modot.mo.gov/RDT/reports/Ri04051/or07009.pdf Report 2007]
+
|[https://spexternal.modot.mo.gov/sites/cm/CORDT/or07009.pdf Report 2007]
−
|-
 
−
|[http://library.modot.mo.gov/RDT/reports/Ri96005/Brief.htm Summary 2000]
 
 
|-
 
|-
−
|'''See also:''' [http://www.modot.gov/services/OR/byDate.htm Innovation Library]
+
|'''See also:''' [https://www.modot.org/research-publications Research Publications]
 
|}
 
|}
−
*Liquid asphalt – EA 90P or CRS-2P
 
−
*Cover aggregate – Iron Mountain trap rock, Joplin chat, or other approved materials
 
−
 
−
==Procedures==
 
−
1. Deck should be thoroughly sounded out and deck repairs made.
 
−
 
−
2. Deck should be cleaned, flushed, and dry prior to sealing.
 
−
 
−
3. Cover expansion devices or other features that are not to be sealed over.
 
−
 
−
4. Chip seals are to extend a minimum of 30 ft. beyond each bridge end.
 
−
 
−
5. Apply liquid asphalt at a rate of 0.3 to 0.5 gal./yd<sup>2</sup> depending on size of cover aggregate and slope of bridge deck.
 
−
 
−
6. Spread 25 to 30 lbs. of cover aggregate per yd<sup>2</sup> immediately following application of liquid asphalt and roll as soon as possible. Adequate cover aggregate must be applied to prevent tracking. Cover aggregate shall not be placed within 2 ft. of curb.
 
−
 
−
7. Lightly broom excess chips after seal is properly cured (when chips are securely held), then open lane to traffic.
 
−
 
−
8. Repeat for adjacent lanes.
 
  
−
9. Return two to three days later to again thoroughly sweep bridge deck to remove loose aggregate. Remove aggregate on lower chords and substructure caps.
+
See [[:Category:170 Maintenance Activity Planning Guidelines#R322 Bridge Preventative Maintenance|R322 Bridge Seal Coats Maintenance Planning Guidelines]].
  
−
==Safety==
+
Index of all [[:Category:170 Maintenance Activity Planning Guidelines#Index of Printable Planning Guides|Maintenance Planning Guidelines]].
−
Watch for flying rock chips and traffic in adjacent lanes. Consider the need to install Loose Gravel signs until the loose aggregate is removed from the bridge deck.
 
  
−
[[Category:771 Bridge Preventative Maintenance Guidelines|771.15]]
+
[[Category:771 Bridge Preventive Maintenance Guidelines|771.19]]

Latest revision as of 13:54, 18 August 2020

Bridge Deck, Sealer
Report 2007
See also: Research Publications

See R322 Bridge Seal Coats Maintenance Planning Guidelines.

Index of all Maintenance Planning Guidelines.

Retrieved from "https://epg.modot.org/index.php?title=771.19_Chip_Seal_to_Entire_Deck&oldid=48144"