Difference between revisions of "Category:626 Rumble Strips"

From Engineering_Policy_Guide
Jump to navigation Jump to search
m (add forms "box and correct link to design exception process)
m (Per TS, replaced now-archaic special sheet with link to new Std. Plan 626.00.)
 
(42 intermediate revisions by 4 users not shown)
Line 1: Line 1:
 +
[[image:626 rumble strip.jpg|left|225px]]
 
{| style="padding:0.3em; margin-left:15px; border:1px solid #a9a9a9; text-align:center; font-size: 95%; background:#f5f5f5" width="160px" align="right"
 
{| style="padding:0.3em; margin-left:15px; border:1px solid #a9a9a9; text-align:center; font-size: 95%; background:#f5f5f5" width="160px" align="right"
 
|-
 
|-
−
|'''Forms'''
+
|'''Form'''
 
|-
 
|-
−
|[[Media:131.4 DESIGN EXCEPTION INFORMATION FORM.doc|Design Exception Information Form]]
+
|[[media:131.4 Design Exception Info.doc|Design Exception Information Form]]
 +
|-
 +
|'''Additional Information'''
 +
|-
 +
|[https://www.modot.org/media/16900 Std. Plan 626.00 Rumble Strips]
 
|}
 
|}
  
 +
Rumble strips are a grooved pattern in the pavement that improves safety by alerting drivers as they unintentionally stray from the roadway. The grooves alert drivers by causing the vehicle’s wheels to noisily and suddenly vibrate when it leaves the driving lane.
  
−
Rumble strips are a grooved pattern in the pavement that makes road travel safer for motorized vehicles.  The grooves alert drivers by causing the vehicle’s wheels to noisily and suddenly vibrate when it leaves the driving lane.
+
This article deals with both [[626.1 Edgeline Rumble Strips|edgeline]] and [[626.2 Centerline Rumble Strips|centerline rumble strips]] as well as the [[626.3 Construction Inspection Guidelines for Sec 626|construction inspection guidelines]] that must be considered to achieve a high-quality product. Guidance is also presented for transverse rumble strips that are warning devices placed perpendicular to traffic across the driving lane.  
−
 
 
−
==626.1 Edgeline Rumble Strips==
 
−
[[image:626 Edgeline Rumble Strips.jpg|right|350px]]
 
−
 
 
−
Edgeline rumble strips are used to enhance [http://www.modot.mo.gov/safety safety] on every [[231.4 Shoulder Width|shoulder]] at least 2 ft. (600 mm) wide, unless the shoulder has a curbed section or is intended to be used as a future travel lane.  Rumble strips are omitted where the posted speed is less than 50 mph.  All major roads will have edgeline rumble strips unless the posted speed is less than 50 mph.  In urban areas, edgeline rumble strips may be omitted on major roads with a [[131.4 Design Exception Process|design exception]] (e.g., noise is a significant issue and safety is not a significant issue).
 
−
 
 
−
Edgeline rumble strips may be used on minor roadways as a specific safety countermeasure with a paved shoulder.  Where several sections of edgeline rumble strips are installed in close proximity, continuity should be maintained.
 
−
 
 
−
Edgeline rumble strips are to be milled into bituminous and portland cement concrete.  Milling has little or no effect on the integrity of the pavement structure and milled rumble strips produce greater noise and vibration than rolled or formed rumble strips.  Refer to [http://www.modot.mo.gov/business/standards_and_specs/documents/62600.pdf Standard Plan 626.00] for details.  Edgeline rumble strips are omitted between the radius points for side road approaches, entrances and median crossovers.  Edgeline rumble strips should be omitted on bridges and on ramps for diamond, single point, partial cloverleaf and similar types of [[:category:234 Interchanges|interchanges]], but may be considered on longer ramps for directional or other large interchanges.  The length of edgeline rumble strip installation is to be estimated and pay items provided.
 
−
 
 
−
Durable, highly reflective edgeline pavement marking material is sprayed over the rumble strip, creating what is often called a “rumble stripe.”  The pavement marking material is a tape with a raised pattern that causes it to be as visible as possible to the driver.
 
−
 
 
−
==626.2 Centerline Rumble Strips==
 
  
−
All two-lane [[media:232 Major Highways Map.pdf|major roads]] with new pavement will have centerline rumble strips unless the posted is less than 50 mph. Centerline rumble strips are desired on all major two-lane roads, and on minor roads with a cross-centerline [http://www.modot.mo.gov/safety/trafficaccidentstatistics.htm accident history]. Rumble strips on a centerline have been shown to reduce head-on crashes by alerting drivers that they are leaving their lane of travel.  On roadways with a travelway width of 20 ft. (6 m), centerline rumble strips become obtrusive and are not recommended.
+
For information on Temporary Rumble Strips for use in work zones, refer to [[616.6 Temporary Traffic Control Zone Devices (MUTCD 6F)#616.6.87 Temporary Rumble Strips (MUTCD 6F.87)|EPG 616.6.87 Temporary Rumble Strips (MUTCD 6F.87)]].
  
−
As with edgeline rumble strips, durable, highly reflective pavement marking material is sprayed over the centerline rumble strip, creating what is often called a “rumble stripe.”  The pavement marking material is a 6 in. wide stripe so that it is as visible as possible to the driver.
+
'''District Responsibility.''' Collaboration with the Central Office Highway Safety and Traffic Division and the Design Division is necessary prior to approval of a design exception to omit or modify these system-wide safety improvements (such as rumble strips) on a project.  
  
−
In order to maintain the integrity of the rumble strip and the pavement, the pavement material must be either concrete or the final lift of bituminous material must be least 1 3/4 in. thick, and the pavement must have a final asphalt thickness of at least 3 3/4 in.  Centerline rumble strips are not to be placed on bridges or within the limits of an intersection with left turn lanes.  The limits of the intersection are defined by the beginning of the tapers for the left turn lanes.  Centerline rumble strips are not to be placed on any joint.  Longitudinal joints shall be offset 10 in. to accommodate the width of the rumble strip.  The length of centerline rumble strip installation should be estimated and pay items provided.
+
It is the district's responsibility to re-install obliterated or deteriorated rumble strips.

Latest revision as of 12:39, 27 July 2021

626 rumble strip.jpg
Form
Design Exception Information Form
Additional Information
Std. Plan 626.00 Rumble Strips

Rumble strips are a grooved pattern in the pavement that improves safety by alerting drivers as they unintentionally stray from the roadway. The grooves alert drivers by causing the vehicle’s wheels to noisily and suddenly vibrate when it leaves the driving lane.

This article deals with both edgeline and centerline rumble strips as well as the construction inspection guidelines that must be considered to achieve a high-quality product. Guidance is also presented for transverse rumble strips that are warning devices placed perpendicular to traffic across the driving lane.

For information on Temporary Rumble Strips for use in work zones, refer to EPG 616.6.87 Temporary Rumble Strips (MUTCD 6F.87).

District Responsibility. Collaboration with the Central Office Highway Safety and Traffic Division and the Design Division is necessary prior to approval of a design exception to omit or modify these system-wide safety improvements (such as rumble strips) on a project.

It is the district's responsibility to re-install obliterated or deteriorated rumble strips.

Retrieved from "https://epg.modot.org/index.php?title=Category:626_Rumble_Strips&oldid=49812"