Difference between revisions of "Category:1009 Aggregate for Drainage"

From Engineering_Policy_Guide
Jump to navigation Jump to search
m (→‎1009.1 Procedure: Per CM, the ITP gives sampling requirements and excel to oracle sheets for reporting material. Thus the Required Field Test tables were removed)
m (updated links)
Line 18: Line 18:
  
 
==1009.2 Acceptance==
 
==1009.2 Acceptance==
Acceptance is based on routine tests in the field to ensure compliance with the requirements of [http://modot.mo.gov/business/standards_and_specs/Sec1009.pdf Sec 1009]. Samples are to be taken at destination or at the source of aggregate production by MoDOT inspectors at intervals of one per 2,000 tons.
+
Acceptance is based on routine tests in the field to ensure compliance with the requirements of [http://www.modot.org/business/standards_and_specs/SpecbookEPG.pdf#page=14 Sec 1009]. Samples are to be taken at destination or at the source of aggregate production by MoDOT inspectors at intervals of one per 2,000 tons.
  
 
==1009.3 Records and Reports==
 
==1009.3 Records and Reports==
Line 45: Line 45:
  
 
====1009.4.2.4 Deleterious Content====
 
====1009.4.2.4 Deleterious Content====
The percentage of deleterious substances in coarse aggregate shall be determined according to [[106.3.2.71 TM-71, Deleterious Content of Aggregate|TM-71, Deleterious Content of Aggregate]] to meet the quality requirements of [http://modot.mo.gov/business/standards_and_specs/Sec1002.pdf Sec 1002]. Where field determinations show a total deleterious content of 2.5 percent or less, including not more than l.0 percent mud balls and shale, the deleterious content is to be inspected visually. The sample is to be tested if visual inspection indicates more than 2.5 percent total deleterious material present in the sample. Source approval samples shall always be tested regardless of the content of deleterious material.
+
The percentage of deleterious substances in coarse aggregate shall be determined according to [[106.3.2.71 TM-71, Deleterious Content of Aggregate|TM-71, Deleterious Content of Aggregate]] to meet the quality requirements of [http://www.modot.org/business/standards_and_specs/SpecbookEPG.pdf#page=14 Sec 1002]. Where field determinations show a total deleterious content of 2.5 percent or less, including not more than l.0 percent mud balls and shale, the deleterious content is to be inspected visually. The sample is to be tested if visual inspection indicates more than 2.5 percent total deleterious material present in the sample. Source approval samples shall always be tested regardless of the content of deleterious material.
  
 
===1009.4.3 Sample Record===
 
===1009.4.3 Sample Record===
 
The sample record shall be completed in SiteManager, as described in [[:Category:101 Standard Forms#Sample Record General Information| Sample Record General Information]] [[image:bulldozer.jpg|20px]], and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in [[106.20 Reporting|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.
 
The sample record shall be completed in SiteManager, as described in [[:Category:101 Standard Forms#Sample Record General Information| Sample Record General Information]] [[image:bulldozer.jpg|20px]], and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in [[106.20 Reporting|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.

Revision as of 10:50, 15 June 2016

MGS Information
Current General Services Specifications (MGS) By Subject


This guidance establishes procedures for the inspection, testing and acceptance of aggregate for drainage.

1009.1 Procedure

Inspection, testing, and sampling will be governed by the instructions contained in EPG 1001 General Requirements for Material.

Samples required for Laboratory tests are as follows:

(a) Initial Evaluation if material has never been tested before.
(b) Source Approval. Must meet 1002 quality as required in EPG 1001.4.2 General Requirements for Material - Source Approval Samples.

1009.2 Acceptance

Acceptance is based on routine tests in the field to ensure compliance with the requirements of Sec 1009. Samples are to be taken at destination or at the source of aggregate production by MoDOT inspectors at intervals of one per 2,000 tons.

1009.3 Records and Reports

All plant records shown in EPG 1001.6 General Requirements for Material - Records and Reports shall be maintained. The material shall be reported through SiteManager (SM) in accordance with Sample Record General Information Bulldozer.jpg.

1009.4 Laboratory Testing for Sec 1009

1009.4.1 Types of Samples Tested

1009.4.1.1 Initial Approval Sample

Tests consist of specific gravity, absorption, and Los Angeles abrasion. The minimum time required for completion of tests is four working days from the date received. Test results and calculations shall be recorded through SM.

1009.4.1.2 Source Approval Sample

Tests consist of sieve analysis, specific gravity, absorption, Los Angeles abrasion, and deleterious content. The minimum time required for completion of tests is four working days from the date received. Test results and calculations shall be recorded through SM.

1009.4.1.3 Production Sample

Tests consist of sieve analysis and deleterious content. The minimum time required for completion of tests is three working days from the date received. Test results and calculations shall be recorded through SM.

1009.4.2 Procedure

1009.4.2.1 Sieve Analysis

Aggregate shall be tested in accordance with AASHTO T 27.

1009.4.2.2 Specific Gravity and Absorption

Aggregate shall be tested according to AASHTO T 85 for specific gravity.

1009.4.2.3 Los Angeles Abrasion

Aggregate shall be tested in accordance with AASHTO T 96.

1009.4.2.4 Deleterious Content

The percentage of deleterious substances in coarse aggregate shall be determined according to TM-71, Deleterious Content of Aggregate to meet the quality requirements of Sec 1002. Where field determinations show a total deleterious content of 2.5 percent or less, including not more than l.0 percent mud balls and shale, the deleterious content is to be inspected visually. The sample is to be tested if visual inspection indicates more than 2.5 percent total deleterious material present in the sample. Source approval samples shall always be tested regardless of the content of deleterious material.

1009.4.3 Sample Record

The sample record shall be completed in SiteManager, as described in Sample Record General Information Bulldozer.jpg, and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in EPG 106.20 Reporting, are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.