User:Hoskir/Revision Request 4305
1
Copy 616.16.3.3 Recommended Advance Warning Sign Minimum Spacing
616.16.3.3 Recommended Advance Warning Sign Minimum Spacing
| Speed Limit1, mph | Sign Spacing2, ft. | |
|---|---|---|
| Undivided Highway | Divided Highway | |
| up to 35 | 2003 | 2003 |
| 40 to 45 | 350 | 500 |
| 50 to 55 | 500 | 1000 |
| 60 to 75 | 1000 | SA-1000 SB-1500 SC-2640 |
|
1 Speed limit is based on posted speed limit. 2 Sign spacing may be adjusted, normally by increasing it, to accommodate field conditions and visibility. 3 For urban low speed, minimum recommended spacing in MUTCD is 100 ft. | ||
2
Copy 616.16.3.4 Recommended Taper Length and Spacing
616.16.3.4 Recommended Taper Length and Spacing
| Speed Limit1, mph | Taper Length2, ft. | Channelizing Spacing 3, ft. | ||
|---|---|---|---|---|
| Shoulder4 (T1) | Lane5 (T2) | Tapers | Buffer/Work Areas | |
| up to 35 | 70 | 245 | 356 | 406 |
| 40 to 45 | 150 | 540 | 406 | 806 |
| 50 to 55 | 185 | 660 | 507 | 807 |
| 60 to 70 | 235 | 840 | 607 | 1207 |
| 75 | 300 | 900 | 607 | 1207 |
|
1 Speed limit is based on posted speed limit. 2 Taper lengths may be adjusted to accommodate crossroads, curves, intersections, ramps or other geometric features. 3 Channelizer spacing may be reduced to discourage traffic encroachment. 4 Based on 10 ft. shoulder width. 5 Based on 12 ft. lane width. 6 Spacing reduced to 1/2 at intersections. 7 Spacing may be reduced to 1/2 at intersections. | ||||
3
Copy 616.18.3 Work Zone Speed Limits
MoDOT has the authority to set speed limits on the state highway system. This power extends to establishing speed limits in temporary traffic control zones, where the speed limit may be reduced from the normal speed limit for safety purposes. Work zones shall be designed to the normal posted speed limit.
A reduced speed limit should be carefully considered before it is imposed, as motorists will only reduce their speed if they perceive a need to do so. Any decision to reduce the speed limit based on an arbitrary, "across the board" or other inappropriate rationale may result in non-compliance with the reduced speed limit by motorists and a false sense of security for workers.
Should a reduced speed limit be deemed appropriate, the following table shows the recommended maximum speed reductions that may be imposed in temporary traffic control zones.
| Activity (i.e. Workers, Equipment or Material) Location | Recommended Work Zone Speed Reduction (When Applicable) |
|---|---|
| 10 ft. beyond edge of travelway to edge of right of way | No speed reduction |
| In traffic lane or within 10 ft. of the traffic lane | 10 mph |
| Head-to-head on multilane | 10 mph |
| Special circumstances within a temporary traffic control work zone may warrant a lower speed limit than recommend above. All speed limit reductions greater than 10 mph shall be documented, submitted to and approved by the District Work Zone Coordinator. | |
After selecting a reduced speed limit based upon the table above, the following guidelines will assist in the proper installation and application of that reduced speed limit in the temporary traffic control zone.
- On divided highways, the reduced speed is applicable to the affected direction of travel only.
- Existing SPEED LIMIT signs within the temporary traffic control zone shall be covered or removed.
- SPEED LIMIT signs indicating the normal speed limit should be installed at the end of the reduced area provided no other reduction is imposed within the next one-half mile or no existing SPEED LIMIT sign is located within the next one-half mile.
- Reduced speed limit signing shall be removed, covered or turned from traffic when conditions requiring the reduced speed no longer exist.
- For two-lane roadways, normal SPEED LIMIT signs are typically installed opposite the work zone SPEED LIMIT sign on the opposite approach facing traffic leaving the work zone.
- Reduced SPEED LIMIT signs are not to be installed on side street approaches or ramps for work limited to main line only. Reduced SPEED LIMIT signs may be installed downstream from the ramp or side street to inform drivers of the work zone speed limit. If the work is on the ramp, or affects the ramp, reduced SPEED LIMIT signs are to be used.
- Posted work zone speed limit shall not be below 35 mph, except when local ordinance provides for a lower speed. The lower speed shall be used when applicable.
- Appropriate warning signs with advisory speed plaques should be used to advise of any specialized situations (i.e., temporary bypass, narrow lanes, etc.).
- For approved speed reductions greater than 10 mph, additional notification should be provided through the use of the SPEED LIMIT XX AHEAD sign. Refer to EPG 616.18.3 Work Zone SPEED LIMIT Figures.
- For approved speed reductions greater than 20 mph, the speed limit should be reduced in two stages. Refer to EPG 616.18.3 Work Zone SPEED LIMIT Figures.
616.18.1 WORK ZONE FINE Sign (CONST-3A)
| Additional Info About Signs Required for Assessing Fines RSMo 304.582.1 |
The WORK ZONE FINE sign shall be specified on projects where all the following criteria are met:
- Duration of the work zone is longer than 4 hours.
- Reduced speed limits are in effect.
- Normal posted speed limit is 60 mph or greater.
- Workers will be present without positive protection (concrete barrier or guardrail).
If a lane closure is used on a roadway with two lanes in the direction of travel, two DO NOT PASS and two PASS WITH CARE signs and two CONST-3X, (SPEEDING/PASSING) plates shall be specified. WORK ZONE plaques shall be specified for all DO NOT PASS signs being used as part of the work zone signing sequence. If a lane closure is used on a roadway with three or more lanes in the direction of travel, the DO NOT PASS and PASS WITH CARE signs and SPEEDING/PASSING plates shall not be specified.
616.18.2 Sign Descriptions and Applications
Sign descriptions and applications are located in EPG 616.6 Temporary Traffic Control Zone Devices.
616.18.3 Work Zone SPEED LIMIT Figures
- Fig. 616.18.3.1, Work Zone Speed Limit Locations within the Advance Warning Area for Divided Roadways
- Fig. 616.18.3.2, Work Zone Speed Limit Locations within Activity Area
- Fig. 616.18.3.3, Work Zone Fine Sign-Speed Limit Locations within the Advance Warning Area
- Fig. 616.18.3.4, Work Zone Speed Limit Locations for Reductions Greater than 20 mph and Reduction in Two Locations
- Fig. 616.18.3.5, Work Speed Limit Locations within a Lane Closure on Two-Lane Road Using Flaggers
4
Copy 616.2.6 Activity Area (MUTCD Section 6B.06)
616.2.6 Activity Area (MUTCD Section 6B.06)
Support. The activity area is the section of the highway where the work activity takes place. It is comprised of the work space, the traffic space, and the buffer space.
The work space is that portion of the highway closed to road users and set aside for workers, equipment, material, and a shadow vehicle, if one is used upstream. Work spaces are usually delineated for road users by channelizing devices or, to exclude vehicles and pedestrians, by temporary barriers.
Option. The work space may be stationary or may move as work progresses.
Guidance. Since there might be several work spaces (some even separated by several miles) within the project limits, each work space should be adequately signed to inform road users and reduce confusion.
Option. The workspace may be supplemented by channelizers and/or barricades placed perpendicular to the flow of traffic to deter non-construction related use of closed lanes.
Support. The traffic space is the portion of the highway in which road users are routed through the activity area.
The buffer space is a lateral and/or longitudinal area that separates road user flow from the work space or an unsafe area, and might provide some recovery space for an errant vehicle.
Guidance. Neither work activity nor storage of equipment, vehicles, or material should occur within a buffer space.
Option. Buffer spaces may be positioned either longitudinally or laterally with respect to the direction of road user flow. The activity area may contain one or more lateral or longitudinal buffer spaces.
A longitudinal buffer space may be placed in advance of a work space.
The longitudinal buffer space may also be used to separate opposing road user flows that use portions of the same traffic lane, as shown in Figure 616.2.6.
If a longitudinal buffer space is used, the values shown in Table 616.2.6 may be used to determine the length of the longitudinal buffer space.
| Speed* | Distance |
|---|---|
| 20 mph | 115 feet |
| 25 mph | 155 feet |
| 30 mph | 200 feet |
| 35 mph | 250 feet |
| 40 mph | 305 feet |
| 45 mph | 360 feet |
| 50 mph | 425 feet |
| 55 mph | 495 feet |
| 60 mph | 570 feet |
| 65 mph | 645 feet |
| 70 mph | 730 feet |
| * Posted speed, off-peak 85th-percentile speed prior to work starting, or the anticipated operating speed | |
Support. Typically, the buffer space is formed as a traffic island and defined by channelizing devices.
When a shadow vehicle, arrow board, or changeable message sign is placed in a closed lane in advance of a work space, only the area upstream of the vehicle, arrow board, or changeable message sign constitutes the buffer space.
Option. The lateral buffer space may be used to separate the traffic space from the work space, as shown in Figures 616.2.3 and 616.2.6, or such areas as excavations or pavement-edge drop-offs. A lateral buffer space also may be used between two travel lanes, especially those carrying opposing flows.
Guidance. The width of a lateral buffer space should be determined by engineering judgment.
Option. When work occurs on a high-volume, highly-congested facility, a vehicle storage or staging space may be provided for incident response and emergency vehicles (for example, tow trucks and fire apparatus) so that these vehicles can respond quickly to road user incidents. This may involve providing storage space at the beginning or end of the activity area or both.
Guidance. Vehicle storage or staging space should not extend into any portion of the buffer space.
