Difference between revisions of "1044.5 Laboratory Testing Guidelines for Sec 1044"

From Engineering_Policy_Guide
Jump to navigation Jump to search
m (article construction)
 
m (→‎1044.5.2 Sample Record: Per CM, replaced archaic "Automation Section" with AWP MA Sample Record, General)
 
(5 intermediate revisions by the same user not shown)
Line 1: Line 1:
 
This article establishes procedures for Laboratory testing and reporting galvanized steel
 
This article establishes procedures for Laboratory testing and reporting galvanized steel
posts.  Refer to [http://www.modot.mo.gov/business/standards_and_specs/Sec1044.pdf Sec 1044] for MoDOT’s specifications.  
+
posts.  Refer to [http://www.modot.org/business/standards_and_specs/SpecbookEPG.pdf#page=14 Sec 1044] for MoDOT’s specifications.  
  
 
==1044.5.1 Procedure==
 
==1044.5.1 Procedure==
Laboratory tests to be performed on the sample are designated by the inspector in the remarks area of SiteManager.
+
Laboratory tests to be performed on the sample are designated by the inspector in the remarks area of AASHTOWARE Project (AWP).
  
 
===1044.5.1.1 Chemical Tests===
 
===1044.5.1.1 Chemical Tests===
The procedure for determining mass of coating shall be according to AASHTO T65. Original test data and calculations shall be recorded in Laboratory workbooks. Test results shall then be recorded through SiteManager.
+
The procedure for determining mass of coating shall be according to AASHTO T65. Original test data and calculations shall be recorded in Laboratory workbooks. Test results shall then be recorded through AWP.
  
 
===1044.5.1.2 Physical Tests===
 
===1044.5.1.2 Physical Tests===
Dimensions, shape, mass, length, and hole punching shall be measured for conformance to [http://www.modot.mo.gov/business/standards_and_specs/documents/90303.pdf Standard Plan 903.03]. To determine the mass per linear foot (linear meter) of a galvanized steel post after fabrication, refer to [[:Category:1044 Posts for Markers and Delineators#1044.3 Calculations|1044.3 Calculations]]. Test results shall be recorded through SiteManager.
+
Dimensions, shape, mass, length, and hole punching shall be measured for conformance to [http://www.modot.mo.gov/business/standards_and_specs/documents/90303.pdf Standard Plan 903.03]. To determine the mass per linear foot (linear meter) of a galvanized steel post after fabrication, refer to [[:Category:1044 Posts for Markers and Delineators#1044.3 Calculations|1044.3 Calculations]]. Test results shall be recorded through AWP.
  
 
==1044.5.2 Sample Record==
 
==1044.5.2 Sample Record==
The sample record shall be completed in SiteManager, as described in [http://wwwi/intranet/cm/materials/vol_3/AS3510.pdf Automation Section 3510], and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in [[106.9 Reporting Test Results|106.9 Reporting Test Results]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.
+
The sample record shall be completed in AWP, as described in [https://epg.modot.org/forms/CM/AWP_MA_Sample_Record_General.docx AWP MA Sample Record, General], and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in [[106.20 Reporting|EPG 106.20 Reporting]], are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.
  
 
[[Category:1044 Posts for Markers and Delineators]]
 
[[Category:1044 Posts for Markers and Delineators]]

Latest revision as of 08:53, 24 November 2021

This article establishes procedures for Laboratory testing and reporting galvanized steel posts. Refer to Sec 1044 for MoDOT’s specifications.

1044.5.1 Procedure

Laboratory tests to be performed on the sample are designated by the inspector in the remarks area of AASHTOWARE Project (AWP).

1044.5.1.1 Chemical Tests

The procedure for determining mass of coating shall be according to AASHTO T65. Original test data and calculations shall be recorded in Laboratory workbooks. Test results shall then be recorded through AWP.

1044.5.1.2 Physical Tests

Dimensions, shape, mass, length, and hole punching shall be measured for conformance to Standard Plan 903.03. To determine the mass per linear foot (linear meter) of a galvanized steel post after fabrication, refer to 1044.3 Calculations. Test results shall be recorded through AWP.

1044.5.2 Sample Record

The sample record shall be completed in AWP, as described in AWP MA Sample Record, General, and shall indicate acceptance, qualified acceptance, or rejection. Appropriate remarks, as described in EPG 106.20 Reporting, are to be included in the remarks to clarify conditions of acceptance or rejection. Test results shall be reported on the appropriate templates under the Tests tab.