Difference between revisions of "751.50 Standard Detailing Notes"

From Engineering_Policy_Guide
Jump to navigation Jump to search
m (updated link)
m (→‎H1. Steel: Per BR, minor clarifications)
(197 intermediate revisions by 2 users not shown)
Line 7: Line 7:
 
|Please refer to  [[media:751.50 Copying Detailing Notes May 2014.docx|Copying Detailing Notes from EPG to MicroStation Drawings]] for additional information.
 
|Please refer to  [[media:751.50 Copying Detailing Notes May 2014.docx|Copying Detailing Notes from EPG to MicroStation Drawings]] for additional information.
 
|}
 
|}
 +
'''Underlined Portions of Notes:'''  Underlined portions of standard detailing notes that are not applicable may be omitted.
 +
  
 
== A. General Notes ==
 
== A. General Notes ==
  
=== A1. Design Specifications, Loadings & Unit Stresses ===
+
=== A1. Design Specifications, Loadings & Unit Stresses and Standard Plans===
  
'''Omit parts not applicable; Omit parts underlined when not applicable. The format for these notes as they would appear on the plans is as follows with the indention shown being optional. For notes applicable to MSE walls see [[#J. MSE Wall Notes|J. MSE Wall Notes]].'''
+
'''The format for these notes as they would appear on the plans is as follows with the indention shown being optional. For notes applicable to MSE walls see [[#J. MSE Wall Notes (Notes for Bridge Standard Drawings)|J. MSE Wall Notes]].'''
  
 
:'''General Notes:'''
 
:'''General Notes:'''
Line 24: Line 26:
 
::''' Design Unit Stresses:'''
 
::''' Design Unit Stresses:'''
 
::: A1.3  
 
::: A1.3  
 +
 +
::'''Standard Plans: '''
 +
:::A1.4
 +
  
 
'''(A1.1) Design Specifications: '''
 
'''(A1.1) Design Specifications: '''
Line 29: Line 35:
 
'''Use for all LRFD standard culverts and standard culverts-bridge designs in which the design and/or details are completely covered by the Missouri Standard Plans for Highway Construction and/or EPG 751.8 in accordance with the following design specifications. '''
 
'''Use for all LRFD standard culverts and standard culverts-bridge designs in which the design and/or details are completely covered by the Missouri Standard Plans for Highway Construction and/or EPG 751.8 in accordance with the following design specifications. '''
 
:::2010 AASHTO LRFD Bridge Design Specifications and 2010 Interim Revisions
 
:::2010 AASHTO LRFD Bridge Design Specifications and 2010 Interim Revisions
 +
<div id="Use for all LRFD bridge final designs initiated"></div>
 +
'''Use for all LRFD bridge final designs initiated on or after June 1, 2020.'''
  
'''Use for all LRFD bridge final designs initiated on or after March 1, 2013.'''
+
:::2020 AASHTO LRFD Bridge Design Specifications (9th Ed.)
 
 
:::2012 AASHTO LRFD Bridge Design Specifications (6th Ed.) and 2013 Interim Revisions
 
 
:::<u>2011 AASHTO Guide Specifications for LRFD Seismic Bridge Design (2nd Ed.) and 2014 Interim Revisions</u> (<u>Seismic</u> <u>Seismic Details</u>)
 
:::<u>2011 AASHTO Guide Specifications for LRFD Seismic Bridge Design (2nd Ed.) and 2014 Interim Revisions</u> (<u>Seismic</u> <u>Seismic Details</u>)
 
:::<u>Seismic Design Category = _ </u>   
 
:::<u>Seismic Design Category = _ </u>   
Line 42: Line 48:
 
:::<u>Bridge Deck Rating = _(1)</u>
 
:::<u>Bridge Deck Rating = _(1)</u>
  
'''Use for all LRFD bridge final designs initiated before March 1, 2013.'''
+
'''Use for all LRFD bridge final designs initiated before June 1, 2020.'''
  
:::2010 AASHTO LRFD Bridge Design Specifications and 2010 Interim Revisions
+
:::2017 AASHTO LRFD Bridge Design Specifications (8th Ed.)
:::<u>2011 AASHTO Guide Specifications for LRFD Seismic Bridge Design (2nd Ed.) and 2012 Interim Revisions</u> (<u>Seismic</u> <u>Seismic Details</u>)
+
:::<u>2011 AASHTO Guide Specifications for LRFD Seismic Bridge Design (2nd Ed.) and 2014 Interim Revisions</u> (<u>Seismic</u> <u>Seismic Details</u>)
 
:::<u>Seismic Design Category = _ </u>   
 
:::<u>Seismic Design Category = _ </u>   
 
:::<u>Design earthquake response spectral acceleration coefficient at 1.0 second period, S<sub>D1</sub> = _ </u>
 
:::<u>Design earthquake response spectral acceleration coefficient at 1.0 second period, S<sub>D1</sub> = _ </u>
Line 63: Line 69:
 
(1) Use when repairing concrete deck. The rating (3 to 9) is from the bridge inspection report.
 
(1) Use when repairing concrete deck. The rating (3 to 9) is from the bridge inspection report.
 
<div id="(A1.2) Design Loading:"></div>
 
<div id="(A1.2) Design Loading:"></div>
 +
  
 
'''(A1.2) Design Loading:'''
 
'''(A1.2) Design Loading:'''
Line 79: Line 86:
  
 
'''Use for all LFD bridge final designs.'''
 
'''Use for all LFD bridge final designs.'''
::<u>HS20-44</u>
+
::<u>HS20-44</u> <u>HS20 Modified</u> <u>(4)</u> <u>(5)</u>  
::<u>HS20 Modified</u>
 
 
::<u>35 lb/sf</u> <u>No</u> Future Wearing Surface
 
::<u>35 lb/sf</u> <u>No</u> Future Wearing Surface
::<u>Military 24,000 lb Tandem Axle</u>
+
::<u>Military 24,000 lb Tandem Axle</u> <u>(5)</u>  
::<u>Defense Transporter Erector Loading</u>
+
::<u>Defense Transporter Erector Loading</u> <u>(5)</u>  
 
::Earth 120 lb/cf, Equivalent Fluid Pressure <u>(2)</u>   
 
::Earth 120 lb/cf, Equivalent Fluid Pressure <u>(2)</u>   
 
::<u>Ø =  &nbsp;</u>
 
::<u>Ø =  &nbsp;</u>
Line 90: Line 96:
 
|valign="top"|(3)||valign="top"|Superstructure:||<u>Simply-Supported</u>, Non-Composite for dead load.<br/><u>Continuous</u> Composite for live load.
 
|valign="top"|(3)||valign="top"|Superstructure:||<u>Simply-Supported</u>, Non-Composite for dead load.<br/><u>Continuous</u> Composite for live load.
 
|}
 
|}
 +
 +
For rehabilitation of decks originally designed using above loads, specify using current wording when the original wording varies from that now used (“Military” used to be specified as “Modified”).
  
 
(1) Include for all culverts and culverts-bridges unless lane load is used.
 
(1) Include for all culverts and culverts-bridges unless lane load is used.
  
(2) Use "45 lb/cf" (minimum) for bridges and retaining walls, and "30 lb/cf (min.), 60 lb/cf (max.)" for box culverts. Modify if Ø angle dictates.
+
(2) For bridges and retaining walls use "45 lb/cf (Min.)" unless the Ø angle requires using a larger value. For box culverts use "30 lb/cf (Min.), 60 lb/cf (Max.)".
  
 
(3) Use with all prestressed concrete structures. Omit underline portions for single spans.  
 
(3) Use with all prestressed concrete structures. Omit underline portions for single spans.  
 +
 +
(4) For rehabilitation of decks originally designed using loads other than those shown, specify loading as shown on original plans.
 +
 +
(5) For rehabilitation of decks specify the original design year in parentheses, e.g. (1965).
  
  
'''(A1.3) Design Unit Stresses:'''
+
 
 +
'''(A1.3) Use for LRFD. (For ASD, LFD, and allowable stresses, see Development Section.)'''
 +
 
 +
::'''Design Unit Stresses:'''
 
::{|
 
::{|
|Class B Concrete (Substructure)||fc = 1,200 psi||f'c = 3,000 psi
+
|Class B Concrete (Substructure)|| ||f'c = 3,000 psi
 
|-
 
|-
|Class B Concrete (Retaining Wall)||fc = 1,200 psi||f'c = 3,000 psi
+
|Class B Concrete (Retaining Wall)|| ||f'c = 3,000 psi
 
|-
 
|-
|Class B-2 Concrete (Drilled Shafts & Rock Sockets)||fc = 1,600 psi||f'c = 4,000 psi
+
|Class B-2 Concrete (Drilled Shafts & Rock Sockets)|| ||f'c = 4,000 psi
 
|-
 
|-
|Class B-1 Concrete (Superstructure)||fc = 1,600 psi||f'c = 4,000 psi
+
|Class B-1 Concrete (Superstructure)|| ||f'c = 4,000 psi
 
|-
 
|-
|Class B-2 Concrete (Superstructure, except<br/> &nbsp; Prestressed <u>Girders</u> <u>Beams</u> and <u>Safety Barrier</u> <u>and</u><br/> &nbsp; <u>Median Barrier</u> Curb)||valign="bottom"| fc = 1,600 psi||valign="bottom"| f'c = 4,000 psi
+
|Class B-2 Concrete (Superstructure, except<br/> &nbsp; Prestressed <u>Girders</u> <u>Beams</u> and Barrier) || ||valign="bottom"| f'c = 4,000 psi
 
|-
 
|-
|Class B-1 Concrete (Substructure)||fc = 1,600 psi||f'c = 4,000 psi
+
|Class B-1 Concrete (Substructure)|| ||f'c = 4,000 psi
 
|-
 
|-
|Class B-1 Concrete (Box Culvert)||fc = 1,600 psi||f'c = 4,000 psi
+
|Class B-1 Concrete (Box Culvert)|| ||f'c = 4,000 psi
 
|-
 
|-
|Class B-1 Concrete (<u>Safety Barrier</u> <u>and</u><br/> &nbsp; <u>Median Barrier</u> Curb)||valign="bottom"| fc = 1,600 psi||valign="bottom"| f'c = 4,000 psi
+
|Class B-1 Concrete (Barrier)|| ||valign="bottom"| f'c = 4,000 psi
 
|-
 
|-
|Class B-2 Concrete (Superstructure, except<br/> &nbsp; <u>Safety Barrier</u> <u>and</u> <u>Median Barrier</u> Curb)||valign="bottom"| fc = 1,600 psi||valign="bottom"| f'c = 4,000 psi (1)
+
|Class B-2 Concrete (Superstructure, except Barrier)|| ||valign="bottom"| f'c = 4,000 psi (1)
 
|-
 
|-
|Reinforcing Steel (Grade 40)||fs = 20,000 psi||fy = 40,000 psi
+
|Reinforcing Steel (Grade 40)|| ||f<sub>y</sub> = 40,000 psi
 
|-
 
|-
|Reinforcing Steel (Grade 60)||fs = 24,000 psi||fy = 60,000 psi
+
|Reinforcing Steel (Grade 60)|| ||f<sub>y</sub> = 60,000 psi
 
|-
 
|-
|Structural Carbon Steel(ASTM A709 Grade 36)||fs = 20,000 psi||fy = 36,000 psi
+
|Structural Carbon Steel(ASTM A709 Grade 36)|| ||f<sub>y</sub> = 36,000 psi
 
|-
 
|-
|Structural Steel (ASTM  A709  Grade 50)||fs = 27,000 psi||fy = 50,000 psi
+
|Structural Steel (ASTM  A709  Grade 50)|| ||f<sub>y</sub> = 50,000 psi
 
|-
 
|-
|Structural Steel (ASTM  A709  Grade 50W)||fs = 27,000 psi||fy = 50,000 psi
+
|Structural Steel (ASTM  A709  Grade 50W)|| ||f<sub>y</sub> = 50,000 psi
 
|-
 
|-
|Structural Steel (ASTM A709 Grade HPS50W)||fs = 27,000 psi||fy = 50,000 psi
+
|Structural Steel (ASTM A709 Grade HPS50W)|| ||f<sub>y</sub> = 50,000 psi
 
|-
 
|-
|Structural Steel (ASTM A709 Grade HPS70W)||fs = 38,000 psi||fy = 70,000 psi
+
|Structural Steel (ASTM A709 Grade HPS70W)|| ||f<sub>y</sub> = 70,000 psi
 
|-
 
|-
|Steel Pile (ASTM A709  Grade <u>36 or</u> 50)||fb = <u>(3)</u> psi||fy = <u>36,000 or</u> 50,000 psi (2)
+
|Structural Steel HP Pile (ASTM A709  Grade 50S)|| ||f<sub>y</sub> = 50,000 psi  
 
|-
 
|-
|Steel Pipe Pile (ASTM A252 Grade <u>2 or</u> 3) || || fy = <u>35,000 or</u> 45,000 psi (2)
+
|Welded or Seamless steel shell (pipe) for CIP pile (ASTM A252 Grade 3)||width="20"| ||   f<sub>y</sub> = 45,000 psi
 
|-
 
|-
 
|colspan="3"|For precast prestressed panel stresses, see Sheet No. _.
 
|colspan="3"|For precast prestressed panel stresses, see Sheet No. _.
 
|-
 
|-
 
|colspan="3"|For prestressed girder stresses, see Sheet<u>s</u> No. _ <u>&</u> _ .
 
|colspan="3"|For prestressed girder stresses, see Sheet<u>s</u> No. _ <u>&</u> _ .
 +
|-
 +
|colspan="3"|For prestressed <u>solid slab</u> <u>voided slab</u> <u>box</u> beam stresses, see Sheet<u>s</u> No. _ <u>&</u> _ .
 
|}
 
|}
  
Line 145: Line 162:
 
(1) Slabs, diaphragms or beams poured integrally with the slab.
 
(1) Slabs, diaphragms or beams poured integrally with the slab.
  
(2) Indicate higher grade and strength only when required by design.
+
Note: Any new construction using structural steels A514 or A517 requires permission of the State Bridge Engineer. Any construction involving these structural steels requires notification to the State Bridge Engineer.
  
(3) <u>6,000</u> <u>9,000</u>  <u>12,000</u> Design bearing for point bearing piles which are to be driven to rock or other point bearing material shall be designed 9,000 psi, unless the Design Layout specifies otherwise.
+
<div id="(A1.4) Standard Plans:"></div>
 
+
'''(A1.4) Use for structural design information only.'''
Note: Any new construction using structural steels A514 or A517 requires permission of the State Bridge Engineer. Any construction involving these structural steels requires notification to the State Bridge Engineer.
+
:::'''Standard Plans:'''
 +
::::703.37, 703.85, 703.86, and 703.87
  
 +
<center>
 +
{|style="padding: 0.3em; margin-left:10px; border:1px solid #a9a9a9; text-align:left; font-size: 95%; background:#f5f5f5" width="950px" align="center"
 +
|-
 +
|Guidance: <br/>
 +
- List in order the Missouri Standard Plans applicable to the structure (omit if there are no applicable standard plans).<br/>
 +
- Above is an example for a right advanced triple box culvert with a flared inlet. Actual standards specified shall be those required for structure type and features.<br/>
 +
<center>
 +
{|border="1" style="text-align:center;" cellpadding="5" cellspacing="0"
 +
|-
 +
! style="background:#BEBEBE"| Standard Plan!! style="background:#BEBEBE"|When Applicable
 +
|-
 +
|703.10 thru 703.87 ||width="300"|Culvert Standards in Accordance with [[750.7 Non-Hydraulic Considerations#750.7.4.1 Standard Plans|EPG 750.7.4.1 Standard Plans ]]
 +
</center>
 +
|}
 +
</center><br/>
 +
- Examples for exclusion (no need to include):<br/>
 +
&nbsp;&nbsp;&nbsp;o Std. Plan 606.60: guardrail transition – roadway item<br/>
 +
&nbsp;&nbsp;&nbsp;o Std. Plans 606.00 and 617.10: delineators for railings and barriers – referenced in standard notes.<br/>
 +
&nbsp;&nbsp;&nbsp;o Std. Plan 609.00: Type A curb for approach slabs– referenced in standard note K1.16<br/>
 +
&nbsp;&nbsp;&nbsp;o Std. Plan 706.35 Bar Supports for Concrete Reinforcement<br/>
 +
&nbsp;&nbsp;&nbsp;o Std. Plan 712.40 Steel Dams at Expansion Devices – supplementary details for construction<br/>
 +
|}
 +
</center>
 
=== A2. Concrete Box Culverts and Other Type Structures ===
 
=== A2. Concrete Box Culverts and Other Type Structures ===
  
Line 207: Line 248:
  
 
'''(A2.8)'''
 
'''(A2.8)'''
:If precast option is used, collars shall be provided between all precast pieces.
+
:If precast option is used, precast box culvert ties in accordance with Sec 733 and Standard Plan 733 shall be provided between all precast sections.  
  
  
 
'''For Box Culverts with transverse joint(s), place notes A2.9 and A2.10 under the Transverse Joint Detail. <font color="purple">[MS Cell]</font color="purple"> The detail and these notes are not needed if an appropriate standard plan is referenced.'''
 
'''For Box Culverts with transverse joint(s), place notes A2.9 and A2.10 under the Transverse Joint Detail. <font color="purple">[MS Cell]</font color="purple"> The detail and these notes are not needed if an appropriate standard plan is referenced.'''
 
+
<div id="(A2.9)"></div>
 
'''(A2.9)'''
 
'''(A2.9)'''
:Filter cloth 3 feet in width and double thickness shall be centered on transverse joints in top slab and sidewalls with edges sealed with mastic or two sided tape.  Filter cloth shall be a subsurface drainage geotextile in accordance with Sec 1011. Cost of furnishing and installing filter cloth will be considered completely covered by the contract unit price for other items.
+
:Filter cloth 3 feet in width and double thickness shall be centered on transverse joints in top slab and sidewalls with edges sealed with mastic or two sided tape.  Filter cloth shall be a separation geotextile in accordance with Sec 1011. Cost of furnishing and installing filter cloth will be considered completely covered by the contract unit price for other items.
 
<div id="(A2.10)"></div>
 
<div id="(A2.10)"></div>
  
Line 244: Line 285:
 
'''Neoprene Pads:'''
 
'''Neoprene Pads:'''
  
'''(A3.2) Does not apply to Type "N" PTFE Bearings & Laminated Neoprene Bearing Pad Assembly.'''
+
'''(A3.2) Does not apply to Type N PTFE Bearings & Laminated Neoprene Bearing Pad Assembly.'''
:<u>Plain</u> <u>and</u> <u>Laminated</u> Neoprene Bearing Pads <u>(Tapered)</u> shall be <u>50</u> <u>60</u> <u>70</u> durometer and shall be in accordance with Sec 716.
+
:Neoprene bearing pads shall be <u>50</u> <u>60</u> <u>70</u> durometer and shall be in accordance with Sec 716.
  
  
 
'''Fabricated Steel Connections:'''
 
'''Fabricated Steel Connections:'''
  
'''(A3.3)  Use on all steel structures.'''
+
'''(A3.3)  Use for all steel structures. Use Type 3 for weathering steel bolted connections and Type 1 for plain or galvanized steel bolted connections.  '''
:Field connections shall be made with 3/4" diameter high strength bolts and 13/16" diameter holes, except as noted.
+
:Field connections shall be made with 3/4" diameter ASTM F3125 Grade A325 <u>Type 1</u> <u>Type 3</u> bolts and 13/16" diameter holes, except as noted.  
  
  
Line 265: Line 306:
 
:Minimum clearance to reinforcing steel shall be 1 1/2", unless otherwise shown.
 
:Minimum clearance to reinforcing steel shall be 1 1/2", unless otherwise shown.
  
 +
<div id="(A3.5.1) Use when uncoated steel"></div>
 +
'''(A3.5.1) Use when uncoated steel may come in contact with galvanized piles (concrete pile cap intermediate bents and pile footings).'''
 +
:Minimum clearance between galvanized piles and uncoated (plain) reinforcing steel including bar supports shall be 1 1/2”. Nylon, PVC, or polyethylene spacers shall be used to maintain clearance.  Nylon cable ties shall be used to bind the spacers to the reinforcement.
  
'''(A3.6) Use when mechanical bar splices (MBS) are to be specified on the plans. The underlined portion shall be added when the total number of MBS on a set of plans is less than 50 not including any required in the approach slabs. Note B1.9.7 may also be required and Note B3.22 may need to be revised. '''
+
'''(A3.6) Use when mechanical bar splices (MBS) are to be specified on the plans. The underlined portion shall be used when mechanical bar splice is not being paid for with pay item 706-10.70. '''
  
 
:MBS refers to mechanical bar splices. Mechanical bar splices shall be in accordance with Sec 706 or 710 <u>except that no measurement will be made for mechanical bar splices and they will be considered completely covered by the contract unit price for other items</u>.
 
:MBS refers to mechanical bar splices. Mechanical bar splices shall be in accordance with Sec 706 or 710 <u>except that no measurement will be made for mechanical bar splices and they will be considered completely covered by the contract unit price for other items</u>.
  
 
+
<div id="Traffic Handling:"></div>
 
'''Traffic Handling:'''
 
'''Traffic Handling:'''
  
'''(A3.7) Use on all grade separations.'''
+
'''(A3.7) Use on all grade separations (new and rehabs) constructed over traffic. The note shall be as specified on the Bridge Memorandum (may not match the following) in accordance with [[751.1 Preliminary Design#751.1.2.6 Vertical and Horizontal Clearances|EPG 751.1.2.6 Vertical and Horizontal Clearances]].'''
:A minimum vertical clearance of <u> &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;</u> from crown of existing lanes and a minimum lateral clearance of <u> &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;</u> centered on existing lanes shall be maintained during construction.
+
 +
:Vertical clearance for Route <u> &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;</u> traffic during construction shall be <u> &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;</u> minimum over a <u> &nbsp; &nbsp; &nbsp; &nbsp; &nbsp;</u> wide horizontal opening of the roadway <u>in each direction</u>.
  
  
Line 280: Line 325:
 
:<u>Structure to be closed during construction.</u> <u>Traffic to be maintained on (1) during construction.</u> See roadway plans for traffic control <u>and Sheet No. __ for staged construction details.</u>
 
:<u>Structure to be closed during construction.</u> <u>Traffic to be maintained on (1) during construction.</u> See roadway plans for traffic control <u>and Sheet No. __ for staged construction details.</u>
  
::{| style="margin: 1em auto 1em auto" align="left"
+
::{| style="margin: 1em auto 1em auto"  
 
|-
 
|-
 
|(1)|| Use “structure” with staged rehabilitation of existing structures.
 
|(1)|| Use “structure” with staged rehabilitation of existing structures.
Line 291: Line 336:
 
|-
 
|-
 
| ||Use “other routes” with new routes and with existing routes that are closed to traffic.
 
| ||Use “other routes” with new routes and with existing routes that are closed to traffic.
 +
|-
 +
|colspan="2" width="1150"|
 
|}
 
|}
  
 +
=== A4. Protective Coatings ===
  
 +
====A4a. Structural Steel Protective Coatings====
  
 +
In "'''General Notes:'''" section of plans, place the following notes under the heading "Structural Steel Protective Coatings:".
  
 +
=====A4a1. <u>Steel Structures- Nonweathering Steel</u>=====
  
 +
'''<u>Coating New Steel (Notes A4a1.1 – A4a1.7)</u>'''
  
 +
'''(A4a1.1) Use the 2<sup>nd</sup> underlined option for grade separations where System I finish field coat is only required on the fascia surfaces, See Sec 1081.  “System I” may be used for water crossings and where note A4a1.3 is used. '''
  
 +
:Protective Coating: System <u>G</u> <u>System I Prime Coat with System I Finish Field Coat and System G Intermediate Field Coat</u> <u>System I</u> in accordance with Sec 1081.
  
 +
'''(A4a1.2)  '''
  
 +
:Prime Coat: The cost of the prime coat will be considered completely covered by the contract unit price for the fabricated structural steel.
  
 +
'''(A4a1.3) For grade separations where System I is preferred for all girder surfaces and not just the fascia surfaces.'''
  
 +
:System I finish coat shall be substituted for System G intermediate coat in Sec 1081.10.3.4.1.5.
  
=== A4. Protective Coatings ===
+
'''(A4a1.4) The coating color shall be as specified on the Design Layout. When note (A4a1.3) is used, omit the 2<sup>nd</sup> sentence'''.
  
====A4a. Structural Steel Protective Coatings====
+
:Field Coat(s): The color of the field coat(s) shall be <u>Gray (Federal Standard #26373)</u> <u>Brown (Federal Standard #30045)</u> <u>Black (Federal Standard #17038)</u> <u>Dark Blue (Federal Standard #25052)</u> <u>Bright Blue (Federal Standard #25095)</u>. The cost of the intermediate field coat will be considered completely covered by the contract <u>lump sum</u> <u>unit</u> price <u>per sq. foot</u> for Intermediate Field Coat (System G). The cost of the finish field coat will be considered completely covered by the contract <u>lump sum</u> <u>unit</u> price <u>per sq. foot</u> for <u>Finish Field Coat (System G)</u> <u>Finish Field Coat (System I)</u>.  
  
In "'''General Notes:'''" section of plans, place the following notes under the heading "Structural Steel Protective Coatings:".
+
'''(A4a1.5) When note (A4a1.3) is used, omit the underlined part.'''
  
=====A4a1. <u>Steel Structures- Nonweathering Steel</u>=====
+
:At the option of the contractor, the <u>intermediate field coat and</u> finish field coat may be applied in the shop. The contractor shall exercise extreme care during all phases of loading, hauling, handling, erection and pouring of the slab to minimize damage and shall be fully responsible for all repairs and cleaning of the coating systems as required by the engineer.
  
'''<u>Coating New Steel (Notes A4a1.1 – A4a1.7)</u>'''
+
'''(A4a1.6) Use for structures with Access Doors'''
  
'''(A4a1.1) '''
+
:Structural steel access doors shall be cleaned and coated in the shop or field with a minimum of two coats of inorganic zinc primer to provide a total dry film thickness of 4 mils minimum, 6 mils maximum. In lieu of coating, the access doors may be galvanized in accordance with ASTM A123 and AASHTO M 232 (ASTM A153), Class C. The cost of coating or galvanizing doors will be considered completely covered by the contract unit price for other items.  
  
:Protective Coating: System <u>G</u> <u>I</u> in accordance with Sec 1081.
+
'''(A4a1.7) Use for structures with Access Doors and when a fabricated structural steel pay item is not included.'''
 +
 +
:Payment for furnishing, coating or galvanizing and installing access doors and frames will be considered completely covered by the contract unit price for other items.  
  
'''(A4a1.2) '''
+
<div id="(A4a1.8.1) Place"></div>
 +
'''(A4a1.8.1) Place the following notes on the plans when alternate galvanized structural steel protective coating is approved by SPM.'''
  
:Prime Coat: The cost of the prime coat will be considered completely covered by the contract unit price for the fabricated structural steel. Tint of the prime coat for System <u>G</u> <u>I</u> shall be similar to the color of the field coat to be used.  
+
:'''(A4a1.8.1a) Place the following note under the notes for “Structural Steel Protective Coatings”.'''
 +
::Alternate A Structural Steel Protective Coating:
 +
::Structural steel shall be galvanized in accordance with ASTM A123 and Sec 1081.
  
'''(A4a1.3) The coating color shall be as specified on the Design Layout. When System I is specified, omit the 2<sup>nd</sup> sentence'''.
+
:'''(A4a1.8.1b) In "General Notes:" section place the following note under the heading "Miscellaneous:”'''
 +
::Alternate bids for structural steel coating shall be completed.
  
:Field Coat(s): The color of the field coat(s) shall be <u>Gray (Federal Standard #26373)</u> <u>Brown (Federal Standard #30045)</u> <u>Black (Federal Standard #17038)</u> <u>Dark Blue (Federal Standard #25052)</u> <u>Bright Blue (Federal Standard #25095)</u>. The cost of the intermediate field coat will be considered completely covered by the contract <u>lump sum</u> <u>unit</u> price <u>per sq. foot</u> for "Intermediate Field Coat (System G)". The cost of the finish field coat will be considered completely covered by the contract <u>lump sum</u> <u>unit</u> price <u>per sq. foot</u> for <u>"Finish Field Coat (System G)"</u> <u>"Finish Field Coat (System I)"</u>.
+
:'''(A4a1.8.1c) Place following information at bottom part of “Estimated Quantities” table. (At least four (4) blank rows should be left at bottom of table to allow for additional entries in the field.)'''
 
+
<center>
'''(A4a1.4) When System I is specified and if finish coat only is required, omit the underlined part.'''
+
{|border="1" style="text-align:center;" cellpadding="5" cellspacing="0"
 
+
|-
:At the option of the contractor, the <u>intermediate field coat and</u> finish field coat may be applied in the shop. The contractor shall exercise extreme care during all phases of loading, hauling, handling, erection and pouring of the slab to minimize damage and shall be fully responsible for all repairs and cleaning of the coating systems as required by the engineer.  
+
!colspan="4"|Estimated Quantities
 +
|-
 +
!Item||Substr.||Superstr.||Total
 +
|-
 +
|Last Pay Item|| || ||
 +
|-
 +
|Blank|| || ||
 +
|-
 +
|ADD ALTERNATE A:|| || ||
 +
|-
 +
|Galvanizing Structural Steel&nbsp;&nbsp;&nbsp;&nbsp; lump sum|| || ||1
 +
|-
 +
|Blank|| || ||
 +
|-
 +
|Blank|| || ||
 +
|-
 +
|Blank|| || ||
 +
|-
 +
|Blank|| || ||
 +
|}
 +
</center>
 +
'''(A4a1.8.2) Place the following note instead of notes A4a1.1 – A4a1.7 on the plans when galvanized structural steel protective coating is approved by SPM.'''
 +
:'''(A4a1.8.2a) '''
 +
::Structural steel shall be galvanized in accordance with ASTM A123 and Sec 1081.
  
'''(A4a1.5) Use for structures with Access Doors'''
+
'''<u>Recoating Existing Steel (Notes A4a1.9 - A4a1.13)</u>'''  
  
:Structural steel access doors shall be cleaned and coated in the shop or field with at least two coats of inorganic zinc primer to provide a minimum dry film thickness of 5 mils. In lieu of coating, the access doors may be galvanized in accordance with ASTM A123 and A153. The cost of coating or galvanizing doors will be considered completely covered by the contract unit price for other items.  
+
'''(A4a1.9) Use the 2<sup>nd</sup> underlined option for grade separations where System I finish field coat is only required on the fascia surfaces. See Sec 1081. “System I” may be used for water crossings and where note A4a1.13 is used.'''
  
'''(A4a1.6) Use for structures with Access Doors and when a fabricated structural steel pay item is not included.'''
+
:Protective Coating: System <u>G</u> <u>System I Prime Coat with System I Finished Field Coat and System G Intermediate Field Coat</u> <u>System I</u> in accordance with Sec 1081.
 
:Payment for furnishing, coating or galvanizing and installing access doors and frames will be considered completely covered by the contract unit price for other items.  
 
  
'''(A4a1.7)'''  
+
'''(A4a1.10)'''
  
:System I finish coat shall be substituted for System G intermediate coat in Sec 1081.3.3.1.4.
+
:Surface Preparation: Surface preparation of the existing steel shall be in accordance with Sec 1081 for Recoating of Structural Steel (System G, H or I). The cost of surface preparation will be considered completely covered by the contract <u>lump sum</u> <u>unit</u> price <u>per sq. foot</u> for Surface Preparation for Recoating Structural Steel.
  
'''<u>Recoating Existing Steel (Notes A4a1.1, A4a1.3, A4a1.11 - A4a1.13)</u> (A4a1.1)'''  
+
'''(A4a1.11) '''
  
'''(A4a1.1)'''
+
:Prime Coat: The cost of the prime coat will be considered completely covered by the contract <u>lump sum</u> <u>unit</u> price <u>per sq. foot</u> for Field Application of Inorganic Zinc Primer. 
  
:Protective Coating: System <u>G</u> <u>I</u> in accordance with Sec 1081.
+
'''(A4a1.12) The coating color shall be as specified on the Design Layout. When note (A4a1.13) is used, omit the 2<sup>nd</sup> sentence.'''
  
'''(A4a1.11)'''
+
:Field Coat(s): The color of the field coat(s) shall be <u>Gray (Federal Standard #26373)</u> <u>Brown (Federal Standard #30045)</u> <u>Black (Federal Standard #17038)</u> <u>Dark Blue (Federal Standard #25052)</u> <u>Bright Blue (Federal Standard #25095)</u>. The cost of the intermediate field coat will be considered completely covered by the contract <u>lump sum</u> <u>unit</u> price <u>per sq. foot</u> for Intermediate Field Coat (System G). The cost of the finish field coat will be considered completely covered by the contract <u>lump sum</u> <u>unit</u> price <u>per sq. foot</u> for <u>Finish Field Coat (System G)</u> <u>Finish Field Coat (System I)</u>.
  
:Surface Preparation: Surface preparation of the existing steel shall be in accordance with Sec 1081 for "Recoating of Structural Steel (System G, H or I)". The cost of surface preparation will be considered completely covered by the contract <u>lump sum</u> <u>unit</u> price <u>per sq. foot</u> for "Surface Preparation for Recoating Structural Steel".
+
'''(A4a1.13) For grade separations where System I is preferred for all girder surfaces and not just the fascia surfaces.'''
  
'''(A4a1.12) '''
+
:System I finish coat shall be substituted for System G intermediate coat in Sec 1081.10.3.4.1.5.
  
:Prime Coat: The cost of the prime coat will be considered completely covered by the contract <u>lump sum</u> <u>unit</u> price <u>per sq. foot</u> for “Field Application of Inorganic Zinc Primer". Tint of the prime coat for System <u>G</u> <u>I</u> shall be similar to the color of the field coat to be used.  
+
'''(A4a1.14) Use for recoating truss bridges. '''
  
'''(A4a.3) The coating color shall be as specified on the Design Layout. When System I is specified, omit the 2<sup>nd</sup> sentence.'''
+
{|style="padding: 0.3em; margin-left:10px; border:1px solid #a9a9a9; text-align:left; font-size: 95%; background:#f5f5f5" width="780px" align="center"  
 
+
|-
:Field Coat(s): The color of the field coat(s) shall be <u>Gray (Federal Standard #26373)</u> <u>Brown (Federal Standard #30045)</u> <u>Black (Federal Standard #17038)</u> <u>Dark Blue (Federal Standard #25052)</u> <u>Bright Blue (Federal Standard #25095)</u>. The cost of the intermediate field coat will be considered completely covered by the contract <u>lump sum</u> <u>unit</u> price <u>per sq. foot</u> for "Intermediate Field Coat (System G)". The cost of the finish field coat will be considered completely covered by the contract <u>lump sum</u> <u>unit</u> price <u>per sq. foot</u> for <u>"Finish Field Coat (System G)"</u> <u>"Finish Field Coat (System I)"</u>.
+
|The length of span that is permissible to drape is to be determined by the designer and given in the note. Typically, ¼ span length is used but greater lengths have been used in the past based on calculations. See Structural Project Manager or Structural Liaison Engineer.
 
+
|}
'''(A4a1.13) Use for recoating truss bridges.  '''
 
 
 
:'''Guidance: The length of span that is permissible to drape is to be determined by the designer and given in the note. Typically, ¼ span length is used but greater lengths have been used in the past based on calculations. See Structural Project Manager or Structural Liaison Engineer. (Create a colored text box similar to what was done for delineator note.)'''
 
  
 
:For the duration of cleaning and recoating the truss spans, the truss span superstructure in any span shall not be draped with an impermeable surface subject to wind loads for a length any longer than <u>1/4</u> the span length at any one time regardless of height of coverage. Simultaneous work in adjacent spans is permissible using the specified limits in each span.  
 
:For the duration of cleaning and recoating the truss spans, the truss span superstructure in any span shall not be draped with an impermeable surface subject to wind loads for a length any longer than <u>1/4</u> the span length at any one time regardless of height of coverage. Simultaneous work in adjacent spans is permissible using the specified limits in each span.  
Line 373: Line 455:
 
:Protective Coating: Calcium Sulfonate System in accordance with Sec 1081.
 
:Protective Coating: Calcium Sulfonate System in accordance with Sec 1081.
 
   
 
   
:Surface Preparation: Surface preparation of the existing steel shall be in accordance with Sec 1081 for "Overcoating of Structural Steel (Calcium Sulfonate System)". The cost of surface preparation will be considered completely covered by the contract <u>lump sum</u> <u>unit</u> price <u>per sq. foot</u> for "Surface Preparation for Overcoating Structural Steel".  
+
:Surface Preparation: Surface preparation of the existing steel shall be in accordance with Sec 1081 for Overcoating of Structural Steel (Calcium Sulfonate System). The cost of surface preparation will be considered completely covered by the contract <u>lump sum</u> <u>unit</u> price <u>per sq. foot</u> for Surface Preparation for Overcoating Structural Steel.  
  
 
'''(A4a1.22) '''
 
'''(A4a1.22) '''
  
:Rust Penetrating Sealer: The rust penetrating sealer shall be applied to the surfaces of all bearings, overlapping steel plates, pin connections, pin and hanger connections and other locations where rust bleeding, pack rust and layered rust is occurring. The cost of the rust penetrating sealer will be considered completely covered by the contract lump sum price for "Calcium Sulfonate Rust Penetrating Sealer".  
+
:Rust Penetrating Sealer: The rust penetrating sealer shall be applied to the surfaces of all bearings, overlapping steel plates, pin connections, pin and hanger connections and other locations where rust bleeding, pack rust and layered rust is occurring. The cost of the rust penetrating sealer will be considered completely covered by the contract lump sum price for Calcium Sulfonate Rust Penetrating Sealer.  
  
 
'''(A4a1.23) Use when a prime coat is not required. '''
 
'''(A4a1.23) Use when a prime coat is not required. '''
Line 385: Line 467:
 
'''(A4a1.24) Use when prime coat is noted on the Bridge Memorandum as required. '''
 
'''(A4a1.24) Use when prime coat is noted on the Bridge Memorandum as required. '''
  
:Prime Coat: The cost of the prime coat will be considered completely covered by the contract <u>lump sum</u> <u>unit</u> price per <u>sq. foot</u> <u>tons</u> for "Calcium Sulfonate Primer".  
+
:Prime Coat: The cost of the prime coat will be considered completely covered by the contract <u>lump sum</u> <u>unit</u> price per <u>sq. foot</u> <u>tons</u> for Calcium Sulfonate Primer.  
  
 
'''(A4a1.25) '''
 
'''(A4a1.25) '''
  
:Topcoat: The color of the topcoat shall be <u>Gray (Federal Standard #26373)</u> <u>Brown (Federal Standard #30045)</u> <u>Tan (Federal Standard #23522)</u> <u>Green (Federal Standard #24260)</u>. The cost of the topcoat will be considered completely covered by the contract unit price per <u>sq. foot</u> <u>tons</u> for "Calcium Sulfonate Topcoat".
+
:Topcoat: The color of the topcoat shall be <u>Gray (Federal Standard #26373)</u> <u>Brown (Federal Standard #30045)</u> <u>Tan (Federal Standard #23522)</u> <u>Green (Federal Standard #24260)</u>. The cost of the topcoat will be considered completely covered by the contract unit price per <u>sq. foot</u> <u>tons</u> for Calcium Sulfonate Topcoat.
  
 
<div id="(A4a.15) Use when two different new coating systems are used. Show detail on plans."></div>
 
<div id="(A4a.15) Use when two different new coating systems are used. Show detail on plans."></div>
Line 416: Line 498:
 
:At the option of the contractor, the intermediate and finish field coats may be applied in the shop. The contractor shall exercise extreme care during all phases of loading, hauling, handling, erection and pouring of the slab to minimize damage and shall be fully responsible for all repairs and cleaning of the coating systems as required by the engineer.  
 
:At the option of the contractor, the intermediate and finish field coats may be applied in the shop. The contractor shall exercise extreme care during all phases of loading, hauling, handling, erection and pouring of the slab to minimize damage and shall be fully responsible for all repairs and cleaning of the coating systems as required by the engineer.  
  
'''<u>Recoating Existing Steel (Notes A4a2.1, A4a2.11 – A4a2.13) </u>'''
+
'''<u>Recoating Existing Steel (A4a2.10 – A4a2.13) </u>'''
  
'''(A4a2.1)'''
+
'''(A4a2.10)'''
  
 
:Protective Coating: System H in accordance with Sec 1080.
 
:Protective Coating: System H in accordance with Sec 1080.
Line 424: Line 506:
 
'''(A4a2.11) '''
 
'''(A4a2.11) '''
  
:Surface Preparation: Surface preparation of the existing steel shall be in accordance with Sec 1080 and Sec 1081 for "Recoating of Structural Steel (System G, H or I)". The cost of surface preparation will be considered completely covered by the contract <u>lump sum</u> <u>unit</u> price <u>per sq. foot</u> for "Surface Preparation for Recoating Structural Steel".  
+
:Surface Preparation: Surface preparation of the existing steel shall be in accordance with Sec 1080 and Sec 1081 for Recoating of Structural Steel (System G, H or I). The cost of surface preparation will be considered completely covered by the contract <u>lump sum</u> <u>unit</u> price <u>per sq. foot</u> for Surface Preparation for Recoating Structural Steel.  
  
 
'''(A4a2.12) '''
 
'''(A4a2.12) '''
  
:Prime Coat: The cost of the prime coat will be considered completely covered by the contract <u>lump sum</u> <u>unit</u> price <u>per sq. foot</u> for <u>Field Application of Inorganic Zinc Primer</u>". Tint of the prime coat for System H shall be similar to the color of the field coat to be used.  
+
:Prime Coat: The cost of the prime coat will be considered completely covered by the contract <u>lump sum</u> <u>unit</u> price <u>per sq. foot</u> for <u>Field Application of Inorganic Zinc Primer</u>.
  
 
'''(A4a2.13) Use same note A4.3 (repeated here for completeness) for existing steel as for new steel. The coating color shall be as specified on the Design Layout. '''
 
'''(A4a2.13) Use same note A4.3 (repeated here for completeness) for existing steel as for new steel. The coating color shall be as specified on the Design Layout. '''
  
:Field Coats: The color of the field coats shall be Brown (Federal Standard #30045). The cost of the intermediate field coat will be considered completely covered by the contract <u>lump sum</u> <u>unit</u> price <u>per sq. foot</u> for "Intermediate Field Coat (System H)". The cost of the finish field coat will be considered completely covered by the contract <u>lump sum</u> <u>unit</u> price <u>per sq. foot</u> for "Finish Field Coat (System H)".
+
:Field Coats: The color of the field coats shall be Brown (Federal Standard #30045). The cost of the intermediate field coat will be considered completely covered by the contract <u>lump sum</u> <u>unit</u> price <u>per sq. foot</u> for Intermediate Field Coat (System H). The cost of the finish field coat will be considered completely covered by the contract <u>lump sum</u> <u>unit</u> price <u>per sq. foot</u> for Finish Field Coat (System H).
  
 
=====A4a3. <u>Miscellaneous</u>=====
 
=====A4a3. <u>Miscellaneous</u>=====
Line 469: Line 551:
  
 
In "'''General Notes:'''" section of plans, place the following notes under the heading "'''Miscellaneous:'''".
 
In "'''General Notes:'''" section of plans, place the following notes under the heading "'''Miscellaneous:'''".
 +
 +
'''(A5.1) Use the following note on all structures that contains non-redundant Fracture Critical Members (FCM).'''
 +
 +
:This structure contains non-redundant Fracture Critical Members (FCM). FCM requirements shall be in accordance with [https://www.modot.org/media/20575 Sec 1080].
  
 
'''(A5.3) Use the following note on all jobs with high strength bolts.'''
 
'''(A5.3) Use the following note on all jobs with high strength bolts.'''
Line 508: Line 594:
  
  
'''Integral End Bents (When bridge slab quantity using note B3.21 table, slab bid per sq. yd.) '''
+
'''Integral End Bents, notes B1.3, B1.4, and B1.5  (When bridge slab quantity using note B3.21 table, slab bid per sq. yd.) '''
  
 
'''(B1.3) (Use on steel structures only.)'''
 
'''(B1.3) (Use on steel structures only.)'''
Line 514: Line 600:
  
 
'''(B1.4) (Use on concrete structures only.)'''
 
'''(B1.4) (Use on concrete structures only.)'''
:All concrete above the construction joint in the end bents <u>(except detached wing walls)</u> is included in the Estimated Quantities for <u>Slab on Concrete I-Girder</u> <u>Slab on Concrete Bulb-Tee Girder</u> <u>Slab on Concrete NU-Girder</u> <u>Slab on Concrete Beam</u> <u>Reinforced Concrete Slab Overlay</u>.
+
:All concrete above the construction joint in the end bents <u>(except detached wing walls)</u> is included in the Estimated Quantities for Slab on Concrete <u>I-Girder</u> <u>Bulb-Tee Girder</u> <u>NU-Girder</u> <u>Beam</u> <u>Adjacent Beam</u>.
 
 
 
 
'''Integral End Bents'''
 
  
 
'''(B1.5)'''
 
'''(B1.5)'''
:All reinforcement in the end bents <u>(except detached wing walls)</u> is included in the Estimated Quantities for <u>Slab on Steel</u> <u>Slab on Concrete I-Girder</u> <u>Slab on Concrete Bulb-Tee Girder</u> <u>Slab on Concrete NU-Girder</u> <u>Slab on Concrete Beam</u> <u>Reinforced Concrete Slab Overlay</u>.
+
:All reinforcement in the end bents <u>(except detached wing walls)</u> <u>and all reinforcement in cast-in-place pile at end bents</u> is included in the Estimated Quantities for Slab on <u>Steel</u> <u>Concrete I-Girder</u> <u>Concrete Bulb-Tee Girder</u> <u>Concrete NU-Girder</u> <u>Concrete Beam</u> <u>Concrete Adjacent Beam</u>.
  
  
Line 526: Line 609:
  
 
'''(B1.5.1)'''
 
'''(B1.5.1)'''
:All reinforcement in the intermediate bent concrete diaphragms except reinforcement embedded in the beam cap is included in the Estimated Quantities for <u>Slab on Concrete I-Girder</u> <u>Slab on Concrete Bulb-Tee Girder</u> <u>Slab on Concrete NU-Girder</u> <u>Slab on Concrete Beam</u> <u>Reinforced Concrete Slab Overlay</u>.
+
:All reinforcement in the intermediate bent concrete diaphragms except reinforcement embedded in the beam cap is included in the Estimated Quantities for Slab on Concrete <u>I-Girder</u> <u>Bulb-Tee Girder</u> <u>NU-Girder</u> <u>Beam</u> <u>Adjacent Beam</u>.
  
 
'''(B1.5.2)'''
 
'''(B1.5.2)'''
:All concrete above the intermediate beam cap is included in the Estimated Quantities for <u>Slab on Concrete I-Girder</u> <u>Slab on Concrete Bulb-Tee Girder</u> <u>Slab on Concrete NU-Girder</u> <u>Slab on Concrete Beam</u> <u>Reinforced Concrete Slab Overlay</u>.
+
:All concrete above the intermediate beam cap is included in the Estimated Quantities for Slab on Concrete <u>I-Girder</u> <u>Bulb-Tee Girder</u> <u>NU-Girder</u> <u>Beam</u> <u>Adjacent Beam</u>.
  
  
Line 535: Line 618:
  
 
'''(B1.5.3)'''
 
'''(B1.5.3)'''
:All reinforcement in the concrete diaphragm at the end bents is included in the Estimated Quantities for <u>Slab on Concrete I-Girder</u> <u>Slab on Concrete Bulb-Tee Girder</u> <u>Slab on Concrete NU-Girder</u> <u>Slab on Concrete Beam</u> <u>Reinforced Concrete Slab Overlay</u>.
+
:All reinforcement in the concrete diaphragm at the end bents is included in the Estimated Quantities for Slab on Concrete <u>I-Girder</u> <u>Bulb-Tee Girder</u> <u>NU-Girder</u> <u>Beam</u> <u>Adjacent Beam</u>.
  
 
'''(B1.5.4)'''
 
'''(B1.5.4)'''
:All concrete in the concrete diaphragm at the end bents is included in the Estimated Quantities for <u>Slab on Concrete I-Girder</u> <u>Slab on Concrete Bulb-Tee Girder</u> <u>Slab on Concrete NU-Girder</u> <u>Slab on Concrete Beam</u> <u>Reinforced Concrete Slab Overlay</u>.
+
:All concrete in the concrete diaphragm at the end bents is included in the Estimated Quantities for Slab on Concrete <u>I-Girder</u> <u>Bulb-Tee Girder</u> <u>NU-Girder</u> <u>Beam</u> <u>Adjacent Beam</u>.
  
  
Line 546: Line 629:
 
:All concrete and reinforcing steel below top of slab and above construction joint in Semi-Deep Abutments is included in the Estimated Quantities for Slab on Semi-Deep Abutment.
 
:All concrete and reinforcing steel below top of slab and above construction joint in Semi-Deep Abutments is included in the Estimated Quantities for Slab on Semi-Deep Abutment.
  
 
+
<div id="(B1.7)"></div>
 
'''End Bents with Expansion Device'''
 
'''End Bents with Expansion Device'''
  
Line 555: Line 638:
 
'''Sidewalk'''
 
'''Sidewalk'''
  
'''(B1.8)'''
+
'''(B1.8)'''  
 
:All concrete and reinforcing steel in sidewalk will be considered completely covered by the contract unit price for Sidewalk (Bridges).
 
:All concrete and reinforcing steel in sidewalk will be considered completely covered by the contract unit price for Sidewalk (Bridges).
  
Line 588: Line 671:
  
 
<div id="(B1.9.7) Use"></div>
 
<div id="(B1.9.7) Use"></div>
'''(B1.9.7) Use when the total number of mechanical bar splices on a set of plans is 50 or greater not including any required in the approach slabs and when mechanical bar splices are to be specified in integral end bents, diaphragms or deck slabs.'''
 
:All mechanical bar splices in the <u>end bents</u> <u>concrete diaphragms at end bents</u> <u>,</u> <u>and</u> <u>intermediate bent concrete diaphragms</u> <u>and</u> <u>slab</u> are included with the Superstructure Quantities.
 
 
  
 
==== B1b. Excavation, Sway Bracing====
 
==== B1b. Excavation, Sway Bracing====
Line 684: Line 764:
 
|style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:3px solid black"|&nbsp;
 
|style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:3px solid black"|&nbsp;
 
|-
 
|-
|align="right"|[[Image:751.50 circled 2.gif]] <math>\, \big\{*</math>
+
|align="right"|
|align="left" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:3px solid black;"|Safety Barrier Curb
+
|align="left" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:3px solid black;"|Type D Barrier  
 
|align="right" style="border-top:1px solid gray; border-bottom:1px solid gray; border-right:1px solid black"|linear foot
 
|align="right" style="border-top:1px solid gray; border-bottom:1px solid gray; border-right:1px solid black"|linear foot
 
|style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"|&nbsp;
 
|style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"|&nbsp;
Line 698: Line 778:
 
|style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:3px solid black"|&nbsp;
 
|style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:3px solid black"|&nbsp;
 
|-
 
|-
|align="right" rowspan="2"|[[Image:751.50 circled 3.gif]] <math>\, \Bigg\{</math>
+
|align="right" rowspan="2"|[[Image:751.50 circled 2.gif]] <math>\, \Bigg\{</math>
 
|style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:3px solid black;"|&nbsp;
 
|style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:3px solid black;"|&nbsp;
 
|style="border-top:1px solid gray; border-bottom:1px solid gray; border-right:1px solid black"|&nbsp;
 
|style="border-top:1px solid gray; border-bottom:1px solid gray; border-right:1px solid black"|&nbsp;
Line 715: Line 795:
  
 
{|
 
{|
|valign="top"|[[Image:751.50 circled 1.gif]]||The following note shall be placed under the estimated quantities box when steel piles are used in Seismic Performance Categories B, C & D.
+
|valign="top"|[[Image:751.50 circled 1.gif]]||The following note shall be placed under the estimated quantities box when steel piles are used in Seismic Categories B, C & D.
 
|}
 
|}
 
+
<div id="(B3.2)"></div>
 
'''(B3.2)'''
 
'''(B3.2)'''
:Cost of channel shear connectors (Pile Anchors) C4 x 5.4 (ASTM A709 Grade 36) in place will be considered completely covered by the contract unit price for Structural Steel Piles ( <u>10 in.</u> <u>12 in.</u> <u>14 in.</u>).
+
:Cost of L4x4 ASTM A709 Grade 36 HP pile anchors and 3/4-inch diameter ASTM F3125 Grade A325 Type 1 Plain bolts, complete in place, will be considered completely covered by the contract unit price for <u>Galvanized</u> Structural Steel Piles (<u>12 in.</u> <u>14 in.</u>).
 
 
  
 
{|
 
{|
|valign="top"|[[Image:751.50 circled 2.gif]]||Place an <math>\, *</math> next to the safety barrier curb in the quantity box and add the following note under the estimated quantities box.
+
|valign="top"|[[Image:751.50 circled 2.gif]]||In special cases, entries are made to the quantities table by Construction personnel after plans are completed.  When notes are placed too close to the bottom of this table, additional quantities cannot be entered efficiently.  The request has been made that space be left for at least four (4) additional entries to the table before notes are placed on the plans.
 
|}
 
|}
  
'''(B3.3)'''
 
:<math>\, *</math> Safety barrier curb shall be cast-in-place <u>option or slip-form option</u>.
 
  
 +
'''(B3.5) Use for CIP pile in all bridges except for continuous concrete slab bridges.'''
 +
:All reinforcement in cast-in-place pile at <u>non-integral end bents</u> <u>and</u> <u>intermediate bents</u> is included in the substructure quantities.
  
{|
+
'''(B3.6) Use for CIP pile in continuous concrete slab bridges.'''
|valign="top"|[[Image:751.50 circled 3.gif]]||In special cases, entries are made to the quantities table by the Construction after plans are completed.  When notes are placed too close to the bottom of this table, additional quantities cannot be entered efficiently. The request has been made that space be left for at least four (4) additional entries to the table before notes are placed on the plans.
+
:All reinforcement in cast-in-place pile at end bents <u>and</u> <u>pile cap intermediate bents</u> is included in the superstructure quantities <u>and all reinforcement in cast-in-place pile at open concrete intermediates bents is included in the substructure quantities</u>.
|}
 
  
 +
'''Place an <math>\, **</math> next to the transverse diamond grooving in the quantity box and add the following note under the estimated quantities box.'''
  
'''The following notes shall be placed under the estimated quantities box when CIP piles are used in Seismic Performance Categories B, C and D.'''
+
'''(B3.7)'''
 +
:<math>\, **</math> MoDOT will allow, at the contractor's discretion, longitudinal or transverse diamond grooving of the surface of the concrete bridge deck.
  
'''(B3.4)'''
+
'''(B3.8) Place a * next to supplementary wearing surface material in the quantity box and add the following note under the estimated quantities box.'''
:All reinforcement in cast-in-place piling at end bents is included in the superstructure quantities.
 
  
'''(B3.5) Do not use for slab bridges with CIP Pile Caps.'''
+
:<font color = "white">(</font color = "white">'''*''' Supplementary wearing surface material will be paid for at the fixed unit price in accordance with Sec 109.
:All reinforcement in cast-in-place piling at intermediate bents is included in the substructure quantities for intermediate bents.
 
  
'''(B3.6) Use for slab bridges with CIP Pile Caps.'''
+
'''(B3.9) Use for jobs with restrictive timelines including weekend only work. See Structural Project Manager or Structural Liaison Engineer. Place a ** next to total surface hydro demolition in the quantity box and add the following note under the estimated quantities box.'''
:All reinforcement in cast-in-place piling at intermediate bents is included in the superstructure quantities for intermediate bents.
 
  
 
+
:<font color = "white">(</font color = "white">'''**''' The minimum allowable water usage shall be 55 gallons per minute.
'''Place an <math>\, **</math> next to the transverse diamond grooving in the quantity box and add the following note under the estimated quantities box.'''
 
 
 
'''(B3.7)'''
 
:<math>\, **</math> MoDOT will allow, at the contractor's discretion, longitudinal or transverse diamond grooving of the surface of the concrete bridge deck.
 
  
 
==== B3b. Box Culverts====
 
==== B3b. Box Culverts====
Line 775: Line 848:
 
:If distance from stream face of exterior wall to exterior wall is <math>\ge</math> 20' then should use (Culverts-Bridge) but if <math><</math> 20' should use (Culverts).
 
:If distance from stream face of exterior wall to exterior wall is <math>\ge</math> 20' then should use (Culverts-Bridge) but if <math><</math> 20' should use (Culverts).
  
==== B3c. Slabs on Steel, Concrete and Semi-Deep Abutment, and Reinforced Concrete Slab Overlays ====
+
==== B3c. Slabs on Steel, Concrete and Semi-Deep Abutment, and Reinforced Concrete Wearing Surfaces ====
  
 
The following table is to be placed on the design plans under the table of estimated quantities.
 
The following table is to be placed on the design plans under the table of estimated quantities.
  
 
Use separate tables for multiple types of slabs on a structure.  
 
Use separate tables for multiple types of slabs on a structure.  
 
+
<div id="(B3.21)"></div>
 
'''(B3.21) <font color="purple">[MS Cell]</font color="purple"> Table of Slab Quantities'''
 
'''(B3.21) <font color="purple">[MS Cell]</font color="purple"> Table of Slab Quantities'''
 
:{|border="0" style="text-align:center;" cellpadding="5" cellspacing="0"
 
:{|border="0" style="text-align:center;" cellpadding="5" cellspacing="0"
Line 792: Line 865:
 
|align="right" style="border-top:1px solid black; border-bottom:1px solid gray; border-right:1px solid black"|cu. yard
 
|align="right" style="border-top:1px solid black; border-bottom:1px solid gray; border-right:1px solid black"|cu. yard
 
|style="border-top:1px solid black; border-bottom:1px solid gray; border-left:1px solid black; border-right:3px solid black" width="75pt"|&nbsp;
 
|style="border-top:1px solid black; border-bottom:1px solid gray; border-left:1px solid black; border-right:3px solid black" width="75pt"|&nbsp;
|-
 
|align="left" width="225pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:3px solid black;"|Reinforcing Steel
 
|align="right" style="border-top:1px solid gray; border-bottom:1px solid gray; border-right:1px solid black"|pound
 
|style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:3px solid black" width="75pt"|&nbsp;
 
 
|-
 
|-
 
|align="left" width="225pt" style="border-top:1px solid gray; border-bottom:3px solid black; border-left:3px solid black;"|Reinforcing Steel (Epoxy Coated)
 
|align="left" width="225pt" style="border-top:1px solid gray; border-bottom:3px solid black; border-left:3px solid black;"|Reinforcing Steel (Epoxy Coated)
Line 801: Line 870:
 
|style="border-top:1px solid gray; border-bottom:3px solid black; border-left:1px solid black; border-right:3px solid black" width="75pt"|&nbsp;
 
|style="border-top:1px solid gray; border-bottom:3px solid black; border-left:1px solid black; border-right:3px solid black" width="75pt"|&nbsp;
 
|}
 
|}
Fill in the blank above and in note below with "'''Slab on Steel'''", "'''Slab on Concrete I-Girder'''", "'''Slab on Concrete Bulb-Tee Girder'''", "'''Slab on Concrete NU-Girder'''", "'''Slab on Semi-Deep Abutment'''", '''"Slab on Concrete Beam"'''  or "'''Reinforced Concrete Slab Overlay'''".
+
Fill in the blank above and in note below with "'''Slab on Steel'''", "'''Slab on Concrete I-Girder'''", "'''Slab on Concrete Bulb-Tee Girder'''", "'''Slab on Concrete NU-Girder'''", "'''Slab on Semi-Deep Abutment'''", '''"Slab on Concrete Beam"''', '''"Slab on Concrete Adjacent Beam"'''  or "'''Reinforced Concrete Wearing Surface'''".
  
"'''Reinforced Concrete Slab Overlay'''" shall be used with double-tee girders and when specified on the Design Layout for solid slab beams, adjacent voided slab beams and adjacent box beams.
+
"'''Slab on Concrete Adjacent Beam'''" shall be used with double-tee girders and when specified on the Design Layout for solid slab beams, adjacent voided slab beams and adjacent box beams.
  
 +
Concrete shall be estimated to the nearest cubic yard instead of 0.1 cubic yard due to variances and assumptions used in this estimate. Reinforcing steel shall be estimated to the nearest 10 pounds.
  
'''(B3.22) Add <u>except MBS</u> if Note B1.9.7 is required. .'''
+
'''(B3.22) '''
:The table of Estimated Quantities for <u> &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; </u> &nbsp; represents the quantities used by the State in preparing the cost estimate for concrete slabs.  The area of the concrete slab will be measured to the nearest square yard longitudinally from end of slab to end of slab and transversely from out to out of bridge slab (or with the horizontal dimensions as shown on the plan of slab).  Payment for prestressed panels, stay-in-place forms, conventional forms, all concrete and coated and uncoated reinforcing steel <u>except MBS</u> will be considered completely covered by the contract unit price for the slab.  Variations may be encountered in the estimated quantities but the variations cannot be used for an adjustment in the contract unit price.
+
:The table of Estimated Quantities for <u> &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; </u> &nbsp; represents the quantities used by the State in preparing the cost estimate for concrete slabs.  The area of the concrete slab will be measured to the nearest square yard longitudinally from end of slab to end of slab and transversely from out to out of bridge slab (or with the horizontal dimensions as shown on the plan of slab).  Payment for <u>prestressed panels,</u> <u>stay-in-place corrugated steel forms,</u> conventional forms, all concrete and epoxy coated reinforcing steel will be considered completely covered by the contract unit price for the slab.  Variations may be encountered in the estimated quantities but the variations cannot be used for an adjustment in the contract unit price.
  
 
'''(B3.23)'''
 
'''(B3.23)'''
Line 819: Line 889:
 
:Bridge deck surface may be finished with a vibratory screed.
 
:Bridge deck surface may be finished with a vibratory screed.
  
'''Stay-In-Place Forms:'''
+
'''Stay-In-Place Corrugated Steel Forms:'''
  
 
'''(B3.30)'''
 
'''(B3.30)'''
Line 828: Line 898:
  
 
'''(B3.32)'''
 
'''(B3.32)'''
:Form sheets shall not rest directly on the top of <u>girder</u> <u>beam</u> <u>or floorbeam</u> flanges.  Sheets shall be securely fastened to form supports with a minimum bearing length of one inch on each end.  Form supports shall be placed in direct contact with the flange.  Welding on or drilling holes in the <u>girder</u> <u>beam</u> <u>or floorbeam</u> flanges will not be permitted.  All steel fabrication and construction shall be in accordance with Secs 1080 and 712. Certified field welders will not be required for welding of the form supports.
+
:Form sheets shall not rest directly on the top of <u>girder</u> <u>beam</u> <u>or floorbeam</u> flanges.  Sheets shall be securely fastened to form supports with a minimum bearing length of one inch on each end.  Form supports shall be placed in direct contact with the flange.  Welding on or drilling holes in the <u>girder</u> <u>beam</u> <u>or floorbeam</u> flanges will not be permitted.  All steel fabrication and construction shall be in accordance with Sec 1080 and 712. Certified field welders will not be required for welding of the form supports.
 
<div id="(B3.33) Use"></div>
 
<div id="(B3.33) Use"></div>
  
 
'''(B3.33) Use “4 psf” for form spans up to 10 feet beyond which a greater dead loading for form spans may need to be considered and used. '''
 
'''(B3.33) Use “4 psf” for form spans up to 10 feet beyond which a greater dead loading for form spans may need to be considered and used. '''
:The design of stay-in-place corrugated steel forms is per manufacturer which shall be in accordance with Sec 703 for false work and forms. Maximum actual weight of corrugated steel forms allowed shall be 4 psf assumed for girder loading.
+
:The design of stay-in-place corrugated steel forms is per manufacturer which shall be in accordance with Sec 703 for false work and forms. Maximum actual weight of corrugated steel forms allowed shall be 4 psf assumed for <u>girder</u> <u>beam</u> loading.
 
<div id="(B3.34) Use this temporary note"></div>
 
<div id="(B3.34) Use this temporary note"></div>
 
'''(B3.34) Use this temporary note until further notice when more is learned about what contractor’s methods are proposed and approved by the engineer.'''
 
'''(B3.34) Use this temporary note until further notice when more is learned about what contractor’s methods are proposed and approved by the engineer.'''
Line 851: Line 921:
 
==== B3d. Asphalt Wearing Surfaces ====
 
==== B3d. Asphalt Wearing Surfaces ====
  
The following table shall be placed under the Table of Estimated Quantities on the design plans for alternate asphaltic concrete wearing surface.
+
'''(B3.50) <font color="purple">[MS Cell]</font color="purple"> Place following table and note near the Estimated Quantities table on the design plans for optional asphaltic concrete wearing surface as specified on the Bridge Memorandum. The table is not required if there are no wearing surface options, instead show the wearing surface and binder type in the details.'''
 
 
 
 
'''(B3.50) <font color="purple">[MS Cell]</font color="purple">'''
 
  
 
:{|border="0" style="text-align:center;" cellpadding="5" cellspacing="0"
 
:{|border="0" style="text-align:center;" cellpadding="5" cellspacing="0"
 
|-
 
|-
 
|rowspan="2"|&nbsp;
 
|rowspan="2"|&nbsp;
!colspan="2" style="border-top:3px solid black; border-bottom:1px solid black; border-left:3px solid black; border-right:3px solid black"|Alternate Asphaltic<br/>Concrete Wearing Surface
+
!colspan="2" style="border-top:3px solid black; border-bottom:1px solid black; border-left:3px solid black; border-right:3px solid black"|Optional Asphaltic<br/>Concrete Wearing Surface
 
|width="175pt"|&nbsp;
 
|width="175pt"|&nbsp;
 
|-
 
|-
 
!width="225pt" style="border-top:1px solid black; border-bottom:1px solid black; border-left:3px solid black; border-right:1px solid black"|Type of Wearing Surface<br/>with Asphalt Binder Type
 
!width="225pt" style="border-top:1px solid black; border-bottom:1px solid black; border-left:3px solid black; border-right:1px solid black"|Type of Wearing Surface<br/>with Asphalt Binder Type
!style="border-top:1px solid black; border-bottom:1px solid black; border-left:1px solid black; border-right:3px solid black" width="75pt"|Mix Used<br/>(<math>\sqrt{}</math>)
+
!style="border-top:1px solid black; border-bottom:1px solid black; border-left:1px solid black; border-right:3px solid black" width="75pt"|Mix Used<br/>()
 
|-
 
|-
 
|<math>\,*</math>
 
|<math>\,*</math>
Line 882: Line 949:
 
|-
 
|-
 
|&nbsp;
 
|&nbsp;
|align="left" colspan="3"|MoDOT construction personnel shall complete column labeled "Mix Used (<math>\sqrt{}</math>)".
+
|align="left" colspan="3"|MoDOT construction personnel shall complete column labeled "Mix Used ()".
 
|}
 
|}
 
  
 
{|
 
{|
 
|valign="top"|<math>\, *</math>
 
|valign="top"|<math>\, *</math>
|The "SP" designates a superpave mixture; the "125" indicates the nominal mixture aggregate size is 12.5 mm, "B" or "C" indicates the design level, the "SM" indicates Stone Mastic Asphalt, and the "LP" indicates the mixture contains limestone/porphyry.  See the Design Layout for the type of Superpave mixture required.
+
|'''Guidance for Detailing:''' The "SP" designates a superpave mixture; the "125" indicates the nominal mixture aggregate size is 12.5 mm, "B" or "C" indicates the design level, the "SM" indicates Stone Mastic Asphalt, and the "LP" indicates the mixture contains limestone/porphyry.  See the Bridge Memorandum for the type of Superpave mixture required.
 
|-
 
|-
 
|&nbsp;
 
|&nbsp;
|See the Design Layout for the asphalt binder required.
+
|See the Bridge Memorandum for the asphalt binder required.
 
|}
 
|}
  
  
 +
'''Place next three notes under the Estimated Quantities table if B3.50 is not required, otherwise place under B3.50.'''
  
'''(B3.53)'''
+
'''(B3.53) The first sentence is not required if B3.50 is not required.'''
:The contractor shall select one of the alternate asphaltic concrete wearing surfaces listed in the table.  The mixture shall be in accordance with Sec 403 and produced in accordance with Sec 404.
+
:<u>The contractor shall select one of the optional asphaltic concrete wearing surfaces listed in the table.</u> The mixture shall be in accordance with Sec 403 and produced in accordance with Sec 404.
  
 
'''(B3.54)'''
 
'''(B3.54)'''
:The area of the asphaltic concrete wearing surface will be measured and computed to the nearest square yard.  This area will be measured transversely from out to out of overlay and longitudinally from end of slab to end of slab.
+
:The area of the asphaltic concrete wearing surface will be measured and computed to the nearest square yard.  This area will be measured transversely from out to out of wearing surface and longitudinally from end of slab to end of slab.
  
 
'''(B3.56)'''
 
'''(B3.56)'''
:Payment for alternate Asphaltic Concrete Wearing Surface will be considered completely covered by the contract unit price per square yard.
+
:Payment for Optional Asphaltic Concrete Wearing Surface will be considered completely covered by the contract unit price per square yard.
  
== C. Reinforcing Steel Notes ==
+
'''(B3.60) <font color="purple">[MS Cell]</font color="purple"> Place following table and notes near the Estimated Quantities table on the design plans for optional ultrathin bonded asphalt wearing surfaces as specified on the Bridge Memorandum. The table is not required if there are no wearing surface options, instead show the wearing surface type in the details.'''
  
 
+
:{|border="0" style="text-align:center;" cellpadding="5" cellspacing="0"
=== C1. Bill of Reinforcing Steel ===
+
|-
 
+
|rowspan="2"|&nbsp;
Place the following notes below or near the "'''Bill of Reinforcing Steel'''" when appropriate.
+
!colspan="2" style="border-top:3px solid black; border-bottom:1px solid black; border-left:3px solid black; border-right:3px solid black"|Optional Ultrathin Bonded Asphalt Wearing Surface
 
+
|width="175pt"|&nbsp;
'''(C1.1) Same marks used for unlike bars on different units.'''
+
|-
 +
!width="225pt" style="border-top:1px solid black; border-bottom:1px solid black; border-left:3px solid black; border-right:1px solid black"|Type of Wearing Surface
 +
!style="border-top:1px solid black; border-bottom:1px solid black; border-left:1px solid black; border-right:3px solid black" width="75pt"|Mix Used<br/>(√)
 +
|-
 +
|
 +
|align="left" width="225pt" style="border-top:1px solid black; border-bottom:1px solid gray; border-left:3px solid black; border-right:1px solid black;"|Type A
 +
|style="border-top:1px solid black; border-bottom:1px solid gray; border-left:1px solid black; border-right:3px solid black" width="75pt"|&nbsp;
 +
|-
 +
|
 +
|align="left" width="225pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:3px solid black; border-right:1px solid black;"|Type B
 +
|style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:3px solid black" width="75pt"|&nbsp;
 +
|-
 +
|
 +
|align="left" width="225pt" style="border-top:1px solid gray; border-bottom:3px solid black; border-left:3px solid black; border-right:1px solid black;"|Type C
 +
|style="border-top:1px solid gray; border-bottom:3px solid black; border-left:1px solid black; border-right:3px solid black" width="75pt"|&nbsp;
 +
|}
 +
 
 +
:MoDOT construction personnel shall complete column labeled "Mix Used (√)".
 +
:The contractor shall select one of the optional ultrathin bonded asphalt wearing surfaces listed in the table.
 +
 
 +
== C. Reinforcing Steel Notes ==
 +
 
 +
 
 +
=== C1. Bill of Reinforcing Steel ===
 +
 
 +
Place the following notes below or near the "'''Bill of Reinforcing Steel'''" when appropriate.
 +
 
 +
'''(C1.1) Same marks used for unlike bars on different units.'''
 
:Bars in the above units are to be billed and tagged separately.
 
:Bars in the above units are to be billed and tagged separately.
  
Line 965: Line 1,059:
 
'''EPOXY COATED REINFORCING STEEL'''
 
'''EPOXY COATED REINFORCING STEEL'''
  
'''Note to Detailer:'''<br/>All reinforcement in the slab and above, and all reinforcement that extends into the slab, shall be epoxy coated; Also, any wing reinforcement that extends into the safety barrier curb shall be epoxy coated.
+
'''Note to Detailer:'''<br/>For epoxy coated reinforcement requirements, see [[751.5 Structural Detailing Guidelines#751.5.9.2.2 Epoxy Coated Reinforcement Requirements|EPG 751.5.9.2.2 Epoxy Coated Reinforcement Requirements]].
  
 
=== C2. Prestressed Girders, Beams & Panels ===
 
=== C2. Prestressed Girders, Beams & Panels ===
Line 973: Line 1,067:
 
Place the C2a notes below or near the table "'''Bill of Reinforcing Steel - Each <u>Girder</u> <u>Beam</u>'''" or under the heading "'''Reinforcing Steel'''" when appropriate.  
 
Place the C2a notes below or near the table "'''Bill of Reinforcing Steel - Each <u>Girder</u> <u>Beam</u>'''" or under the heading "'''Reinforcing Steel'''" when appropriate.  
  
'''(C2a.1) '''
+
'''(C2a.1) Use underline portion when bending diagrams are detailed as such.'''
:All dimensions are out to out.  
+
:All dimensions are out to out. <u>Use symmetry for dimensions not shown.</u>
  
 
'''(C2a.2) '''
 
'''(C2a.2) '''
Line 994: Line 1,088:
 
'''(C2b.10) Add <u>bar</u> for NU-girders and Double T.  '''
 
'''(C2b.10) Add <u>bar</u> for NU-girders and Double T.  '''
 
:All <u>bar</u> reinforcement shall be Grade 60.   
 
:All <u>bar</u> reinforcement shall be Grade 60.   
 
'''(C2b.11) Use only for NU-girders and Double T.  '''
 
:Welded Wire Reinforcement (WWR) shall be in accordance with AASHTO M 221.
 
  
 
'''(C2b.20) Use only for I-girders, bulb-tee girders and alternate bar reinforced NU-girders.  '''
 
'''(C2b.20) Use only for I-girders, bulb-tee girders and alternate bar reinforced NU-girders.  '''
 
:The two D1 bars may be furnished as one bar at the fabricator's option.  
 
:The two D1 bars may be furnished as one bar at the fabricator's option.  
  
'''(C2b.30) Use for all girders and beams except WWR reinforced NU-girders and double-tee girders.  Add <u>and C1</u> for bulb-tee girders only. Most likely will need to add more bars if girder steps exists.  '''
+
'''(C2b.30) Use for all girders except WWR reinforced NU-girders and double-tee girders.  Add <u>and C1</u> for bulb-tee girders only. Most likely will need to add more bars if girder steps exist.  '''
  
 
:All B1 <u>and C1</u> bars shall be epoxy coated.   
 
:All B1 <u>and C1</u> bars shall be epoxy coated.   
Line 1,010: Line 1,101:
 
'''(C2b.32) Use only for double-tee girders.  '''
 
'''(C2b.32) Use only for double-tee girders.  '''
 
:All S and U reinforcing bars shall be epoxy coated.  
 
:All S and U reinforcing bars shall be epoxy coated.  
 +
 +
'''(C2b.33) Use only for spread and adjacent beams.'''
 +
:All S2 bars shall be epoxy coated.
 
   
 
   
 
'''C2c. Additional Notes for Prestressed Panels '''
 
'''C2c. Additional Notes for Prestressed Panels '''
Line 1,035: Line 1,129:
 
:Minimum reinforcement steel length shall be 2'-0".
 
:Minimum reinforcement steel length shall be 2'-0".
  
== D. Temporary Bridge Notes ==
+
== D. Temporary Bridge (Notes for Bridge Standard Drawings)==
  
  
Line 1,042: Line 1,136:
 
Place the following notes on the front sheet.
 
Place the following notes on the front sheet.
  
'''(D1.1)'''
+
'''(D1.1) Place in General Notes on the front sheet under the heading “Timber:”. '''
:Timber:
+
:All timber shall be standard rough sawn.  At the contractor's option, timber may be untreated or protected with commercially applied timber preservatives.  All timber shall have a minimum strength of 1500 psi and shall be either douglas fir in accordance with paragraph 123B (MC-19), 124B (MC-19) and 130BB of the current edition of Standard Grading Rules for West Coast Lumber, southern pine in accordance with paragraphs 312 (MC-19), 342 (MC-19) and 405.1 of the current edition of Southern Pine Inspection Bureau Grading Rules, or a satisfactory grade of sound native oak.
:&nbsp; &nbsp; &nbsp; All timber shall be standard rough sawn.  At the contractor's option, timber may be untreated or protected with commercially applied timber preservatives.  All timber shall have a minimum strength of 1500 psi and shall be either douglas fir in accordance with paragraph 123B (MC-19), 124B (MC-19) and 130BB of the current edition of Standard Grading Rules for West Coast Lumber, southern pine in accordance with paragraphs 312 (MC-19), 342 (MC-19) and 405.1 of the current edition of Southern Pine Inspection Bureau Grading Rules, or a satisfactory grade of sound native oak.
 
  
'''(D1.2)'''
+
'''(D1.2) Use for bolts and studs: '''
:Bolts:
 
:&nbsp; &nbsp; &nbsp; All bolts shall be high strength ASTM A325 except as noted.
 
  
'''(D1.3)'''
+
:(D1.2a) All bolts shall be ASTM F3125 Grade A325 Type <u>3,</u> except as noted.  
:Misc:
 
:&nbsp; &nbsp; &nbsp; The superstructure <u>only</u> <u>& cap beam units</u> will be provided by the State and shall be transported from <u> &nbsp; &nbsp; &nbsp; &nbsp; </u> &nbsp;Maintenance Lot.  The superstructure shall be returned and stored at the same location as designated by the engineer after Bridge No. <u> &nbsp; &nbsp; &nbsp; &nbsp; </u> &nbsp;is open to traffic.
 
  
'''(D1.4)'''
+
:(D1.2b) All ASTM A307 bolts and their accompanying hex nuts and washers and all ASTM A449 Type 1 studs and their accompanying heavy hex nuts shall be galvanized in accordance with AASHTO M 232 (ASTM A153), Class C.
:&nbsp; &nbsp; &nbsp; All structural steel shall be ASTM A709 Grade 50W except piles, sway bracing, thrie beam rail assembly and structural tubing.  Structural tubing coating shall be in accordance with Sec 718.
+
 
 +
'''(D1.3) Place in General Notes on the front sheet under the heading “Miscellaneous:”. '''
 +
:The superstructure <u>only</u> <u>and cap beam units</u> will be provided by the State and shall be transported from <u> &nbsp; &nbsp; &nbsp; &nbsp; </u> &nbsp;Maintenance Lot.  The superstructure shall be returned and stored at the same location as designated by the engineer after Bridge No. <u> &nbsp; &nbsp; &nbsp; &nbsp; </u> &nbsp;is open to traffic.
 +
 
 +
'''(D1.4) Place in General Notes on the front sheet under the heading “Structural Steel:”. '''
 +
:All structural steel shall be ASTM A709 Grade 50W except piles, sway bracing, thrie beam rail assembly and structural tubing.  Structural tubing coating shall be in accordance with Sec 718.
 +
 
 +
'''(D1.5) Place in General Notes on the front sheet under the heading “Substructure:”. '''
 +
:All substructure items specified in Sec 718.3.1 except for the <u>pile point reinforcement and</u> sway bracing will be considered completely covered by the contract unit price for Structural Steel Piles (14 in.).  
  
 
'''(D1.11) Place with shim plate details on the bent sheet.'''
 
'''(D1.11) Place with shim plate details on the bent sheet.'''
:Shim plates may be used between pile and channel at the end bents or angle at the intermediate bents.  Shim plates may vary in thickness from 1/16" to thickness required.
+
:Shim plates may be used between pile and channel at the end bents or angle at the intermediate bents.  Shim plates may vary in thickness from 1/16 inch to thickness required.
  
'''(D1.21) Place near half section of bridge flooring.'''
+
'''(D1.21) Place near half section of bridge flooring on the superstructure sheet.'''
:Steel bridge flooring shall be Foster 5" RB/8.0 or American Bridge 5" Open I-Beam-Lok Type 8S open steel bridge flooring. Trim bars shall be required at the sides and ends of each 39'-10 1/2" unit.
+
:Steel bridge flooring shall be Foster 5-Inch RB 8.2M open steel bridge flooring or equivalent. Trim bars shall be required at the sides and ends of each 39'-10 1/2" unit.  
  
'''(D1.22)'''
+
'''(D1.22) '''  
:Note: Field connections shall be 7/8"&oslash; high strength bolts with holes 1 1/16"&oslash; except as noted.
+
:Note: Field connections shall be made with 7/8"ø ASTM F3125 Grade A325 Type 3 bolts and 1 1/16"ø holes, except as noted.
  
'''(D1.23) Place near details of u-bolts lifting device.'''
+
'''(D1.23) Place near details of U-bolts lifting device on the superstructure sheet.'''
:U-bolts lifting device shall be on the inside top flange at both ends of each exterior stringer of each unit.  U-bolts shall be removed during the time the bridge is open to traffic.  Position of the U-bolts may be shifted slightly to miss the bars in the flooring.
+
:U-bolts lifting device shall be on the inside top flange at both ends of each exterior beam of each unit.  U-bolts shall be removed during the time the bridge is open to traffic.  Position of the U-bolts may be shifted slightly to miss the bars in the flooring.
  
 
== E. General Elevation and Plan Notes ==
 
== E. General Elevation and Plan Notes ==
Line 1,074: Line 1,171:
 
=== E1. Excavation and Fill ===
 
=== E1. Excavation and Fill ===
  
Remove Old Roadway Fill Under Structure (When specified on the Design Layout.)
+
'''(E1.1) Use when specified on the Design Layout.'''  
 
+
:Existing roadway fill under the ends of the bridge shall be removed as shown. Removal of existing roadway fill will be considered completely covered by the contract unit price for roadway excavation.
'''(E1.1)'''
 
:Old roadway fill under the ends of the bridge shall be removed as shown. Removal of old roadway fill will be considered completely covered by the contract unit price for roadway excavation.
 
 
 
 
 
Fill at Pile Cap End Bents (All pile cap end bents)
 
  
'''(E1.4) (*) Applies to Semi-Deep Abutment.'''
+
'''(E1.4) Use for fill at pile cap end bents. Use <u>approach</u> for semi-deep abutments.'''
:Roadway fill shall be completed to the final roadway section and up to the elevation of the bottom of the concrete <u>approach</u>'''(*)''' beam within the limits of the structure and for not less than 25 feet in back of the fill face of the end bents before any piles are driven for any bents falling within the embankment section.
+
:Roadway fill shall be completed to the final roadway section and up to the elevation of the bottom of the concrete <u>approach</u> beam within the limits of the structure and for not less than 25 feet in back of the fill face of the end bents before any piles are driven for any bents falling within the embankment section.
  
 
=== E2. Foundation Data Table ===
 
=== E2. Foundation Data Table ===
Line 1,090: Line 1,182:
 
The following table is to be placed on the design plans and filled out as indicated.
 
The following table is to be placed on the design plans and filled out as indicated.
  
'''(E2.1) <font color="purple">[MS Cell] (E2.1A, E2.1B, E2.1C and E2.1D)</font color="purple"> (Example: Use the underlined parts in the bent headings for bridges having detached wing walls at end bents only.  Remove the rows CIP Type and CIP Standard Plan if CIP piles are not used.)'''
+
'''(E2.1) <font color="purple">[MS Cell] (E2.1)</font color="purple"> (Example: Use the underlined parts in the bent headings for bridges having detached wing walls at end bents only.) '''
 
 
 
 
[[image:750 E2.1.jpg|center|1000px]]
 
  
 
<center>
 
<center>
:{|border="2" style="text-align:center;" cellpadding="5" cellspacing="0"
+
{|border="1" style="text-align:center;" cellpadding="5" cellspacing="0"
 
|-
 
|-
|colspan="8" align="left"|'''<sup>1</sup>''' For LFD: For bridges in Seismic Performance Categories B, C and D, the design bearing values for load bearing piles given in the table should be the larger of the following two values: <br/> &nbsp; 1. Design bearing value for AASHTO group loads I thru VI. <br/> &nbsp; 2. Design bearing for seismic loads / 2.0
+
!colspan="8" style="background:#BEBEBE"| Foundation Data<sup>1</sup>
 
|-
 
|-
|colspan="8" align="left"|'''Additional notes:'''<br/> (On the plans, report the following definition(s) just below the foundation data table for the specific method(s) used.)<br/>
+
!rowspan="2" style="background:#BEBEBE"|Type!!rowspan="2" style="background:#BEBEBE" colspan="2"|Design Data!!colspan="5" style="background:#BEBEBE"| Bent Number
DT = Dynamic Testing<br/>
+
|-
DF = FHWA-modified Gates Dynamic Formula<br/>
+
!style="background:#BEBEBE"|1 <u>(Detached<br/>Wing Walls<br/>Only)</u> !!style="background:#BEBEBE"|1 <u>(Except<br/>Detached<br/>Wing Walls)</u> !!style="background:#BEBEBE"|2 !!style="background:#BEBEBE"| 3 !!style="background:#BEBEBE"|4
WEAP = Wave Equation Analysis of Piles<br/>(On the plans, report the following equation(s) just below the foundation data table for the specific foundation(s) used.)<br/>'''Rock Socket (Drilled Shafts):'''<br/>Minimum Nominal Axial Compressive Resistance (Side Resistance + Tip Resistance) = Maximum Factored Loads/Resistance Factors<br/>'''Spread Footings:'''<br/>Minimum Nominal Bearing Resistance = Maximum Factored Loads/Resistance Factor <br/>'''Load Bearing Pile:'''<br/>Minimum Nominal Axial Compressive Resistance = Maximum Factored Loads/Resistance Factor
+
|-
|}
+
|rowspan="11"|'''Load<br/>Bearing<br/>Pile'''|| colspan="2" align="left" width="300"|CECIP/OECIP/HP Pile Type and Size||CECIP 14"||CECIP 14"||CECIP 16"|| OECIP 24"||HP 12x53
 
+
|-
 +
|colspan="2" align="left" width="300"|Number [[image:751.50 ea.jpg|34px|right]]||6||8||15||12||6
 +
|-
 +
|colspan="2" align="left" width="300"|Approximate Length Per Each [[image:751.50 ft.jpg|20px|right]]||50||50||60||40||53
 +
|-
 +
|colspan="2" align="left" width="300"|Pile Point Reinforcement[[image:751.50 ea.jpg|34px|right]]||All||All|| - ||All||All
 +
|-
 +
|colspan="2" align="left" width="300"|Min. Galvanized Penetration (Elev.) [[image:751.50 ft.jpg|20px|right]]||303||295<sup>'''4'''</sup>||273||Full Length||300
 +
|-
 +
|colspan="2" align="left" width="300"|Est. Max. Scour Depth 100<sup>'''2'''</sup> (Elev.) [[image:751.50 ft.jpg|20px|right]]|| - || - ||285 || - || -
 +
|-
 +
|colspan="2" align="left" width="300"|Minimum Tip Penetration (Elev.) [[image:751.50 ft.jpg|20px|right]]||285||303||270|| - || -
 +
|-
 +
|colspan="2" align="left" width="300"|Criteria for Min. Tip Penetration ||Min. Embed.||Min. Embed.|| Scour || - || -
 +
|-
 +
|colspan="2" align="left" width="300"|Pile Driving Verification Method || DT ||DT ||DT||DT||DF
 +
|-
 +
|colspan="2" align="left" width="300"|Resistance Factor||0.65|| 0.65|| 0.65|| 0.65|| 0.4
 +
|-
 +
|colspan="2" align="left" width="300"|<u>Design Bearing</u><sup>'''3'''</sup> <u>Minimum Nominal Axial</u><br/><u>Compressive Resistance</u> [[image:751.50 kip.jpg|27px|right]]||175||200||300||600||250
 +
|-
 +
|rowspan="2"|'''Spread<br/>Footing||colspan="2" align="left"|Foundation Material || - || - ||Weak Rock||Rock|| -
 +
|-
 +
|colspan="2" align="left"|<u>Design Bearing</u> <u>Minimum Nominal</u><br/><u>Bearing Resistance</u> [[image:751.50 ksf.jpg|30px|right]]|| - || - ||10.2||22.6|| -
 +
|-
 +
|rowspan="8"|'''Rock<br/>Socket'''||colspan="2" align="left"|Number [[image:751.50 ea.jpg|34px|right]]|| - || - || 2 ||3|| -
 +
|-
 +
|rowspan="3" width="35"|[[image:751.50 Layer 1.jpg|center|24px]]||align="left" width="265"|Foundation Material|| - || - || Rock||Rock|| -
 +
|-
 +
| align="left"|Elevation Range [[image:751.50 ft.jpg|20px|right]]|| - || - ||410-403||410-398|| -
 +
|-
 +
| align="left"|<u>Design Side Friction</u><br/><u>Minimum Nominal Axial</u><br/><u>Compressive Resistance</u><br/><u>(Side Resistance)</u> [[image:751.50 ksf.jpg|30px|right]]|| - || - ||20.0||20.0|| -
 +
|-
 +
|rowspan="3"|[[image:751.50 Layer 2.jpg|center|21px]]|| align="left" |Foundation Material|| - || - ||Weak Rock|| - || -
 +
|-
 +
| align="left"|Elevation Range [[image:751.50 ft.jpg|20px|right]]|| - || - ||403-385|| - || -
 +
|-
 +
| align="left"|<u>Design Side Friction</u><br/><u>Minimum Nominal Axial</u><br/><u>Compressive Resistance</u><br/><u>(Side Resistance)</u> [[image:751.50 ksf.jpg|30px|right]]|| - || - ||9.0|| - || -
 +
|-
 +
|colspan="2" align="left"|<u>Design End Bearing</u><br/><u>Minimum Nominal Axial</u><br/><u>Compressive Resistance</u><br/><u>(Tip Resistance)</u> [[image:751.50 ksf.jpg|30px|right]]|| - || - ||12||216|| -
 +
|-
 +
|colspan="8" align="left"|'''1'''  Show only required CECIP/OECIP/HP pile data for specific project.
 +
|-
 +
|colspan="8" align="left"|'''2''' Show maximum of total scour depths estimated for multiple return periods in years from Preliminary design which should be given on the Design Layout. Show the controlling return period (e.g. 100, 200, 500). If return periods are different for different bents, add a new line.
 +
|-
 +
|colspan="8" align="left"|'''3''' For LFD: For bridges in Seismic Performance Categories B, C and D, the design bearing values for load bearing piles given in the table should be the larger of the following two values: <br/> &nbsp; 1. Design bearing value for AASHTO group loads I thru VI. <br/> &nbsp; 2. Design bearing for seismic loads / 2.0
 +
|-
 +
|colspan="8" align="left"|'''4''' It is possible that min. tip penetration (elev.) can be higher than min. galvanized penetration (elev.).
 +
|}
 +
 
 +
{|border="2" style="text-align:center;" cellpadding="5" cellspacing="0"
 +
|-
 +
| align="left"|'''Additional notes:'''<br/> On the plans, report the following definition(s) just below the foundation data table for the specific method(s) used:<br/>
 +
DT = Dynamic Testing<br/>
 +
DF = FHWA-modified Gates Dynamic Pile Formula<br/>
 +
WEAP = Wave Equation Analysis of Piles<br/>
 +
SLT = Static Load Test<br/><br/>On the plans, report the following definition(s) just below the foundation data table for CIP Pile:<br/>CECIP = Closed Ended Cast-In-Place concrete pile<br/>OECIP = Open Ended Cast-In-Place concrete pile<br/><br/>On the plans, report the following equation(s) just below the foundation data table for the specific foundation(s) used:<br/>'''Rock Socket (Drilled Shafts):'''<br/>Minimum Nominal Axial Compressive Resistance (Side Resistance + Tip Resistance) = Maximum Factored Loads/Resistance Factors<br/>'''Spread Footings:'''<br/>Minimum Nominal Bearing Resistance = Maximum Factored Loads/Resistance Factor <br/>'''Load Bearing Pile:'''<br/>Minimum Nominal Axial Compressive Resistance = Maximum Factored Loads/Resistance Factor  
 +
|}
 +
 
  
 
</center>
 
</center>
Line 1,113: Line 1,260:
 
|colspan="3" align="left"|<b>Guidance for Using the Foundation Data Table:</b>
 
|colspan="3" align="left"|<b>Guidance for Using the Foundation Data Table:</b>
 
|-
 
|-
|rowspan="18"| || rowspan="3"|Pile Driving Verification Method ||width="350px"|Modified Gates Formula
+
|rowspan="18"| || rowspan="4"|Pile Driving Verification Method ||width="350px"|DF = FHWA-Modified Gates Dynamic Pile Formula  
 
|-
 
|-
|Dynamic Pile Testing
+
|DT = Dynamic Testing  
 
|-
 
|-
|Other Method
+
|WEAP = Wave Equation Analysis of Piles
 +
|-
 +
|SLT = Static Load Test
 
|-
 
|-
 
|colspan="7"  style="background:#BEBEBE"|
 
|colspan="7"  style="background:#BEBEBE"|
Line 1,137: Line 1,286:
 
|colspan="7"  style="background:#BEBEBE"|
 
|colspan="7"  style="background:#BEBEBE"|
 
|-
 
|-
|Hammer Energy Required ||See [http://www.modot.org/business/standards_and_specs/SpecbookEPG.pdf#page=11 Sec 702.]
+
|colspan="7"|'''Elevation reporting accuracy: Report to nearest foot for min. tip penetration, pile cleanout penetration, max. galvanized depth and est. max. scour depth(Any more accuracy is acceptable but not warranted.)'''
|-
 
|colspan="7" style="background:#BEBEBE"|
 
 
|-
 
|-
 
|colspan="3"|'''For LFD Design'''
 
|colspan="3"|'''For LFD Design'''
Line 1,150: Line 1,297:
 
|}
 
|}
  
'''Shallow Footings (When specified on the Design Layout.)'''
+
'''Shallow Footings '''
  
'''(E2.10)'''
+
'''(E2.10) (Use when shallow footings are specified on the Design Layout.)'''
  
 
:In no case shall footings of Bents No. <u> &nbsp;  &nbsp;  &nbsp;  </u> and <u> &nbsp;  &nbsp;  &nbsp;  </u> be placed higher than elevations shown <u> &nbsp;  &nbsp;  &nbsp;  </u> and  <u> &nbsp;  &nbsp;  &nbsp;  </u>, respectively.
 
:In no case shall footings of Bents No. <u> &nbsp;  &nbsp;  &nbsp;  </u> and <u> &nbsp;  &nbsp;  &nbsp;  </u> be placed higher than elevations shown <u> &nbsp;  &nbsp;  &nbsp;  </u> and  <u> &nbsp;  &nbsp;  &nbsp;  </u>, respectively.
Line 1,165: Line 1,312:
 
<div id="(E2.22) (Use the following note"></div>
 
<div id="(E2.22) (Use the following note"></div>
  
'''(E2.22) (Use the following note when pile point reinforcement is required)'''
+
'''(E2.22) (Use when estimated maximum scour depth (elevation) for CIP piles is required.)   '''
:Manufactured pile point reinforcement shall be used on all piles in this structure<u> at Bent(s) No. &nbsp;  &nbsp;  &nbsp;  and  &nbsp;  &nbsp;  &nbsp;  </u>.
+
:Estimated Maximum Scour Depth (Elevation) shown is for verifying <u>Minimum Nominal Axial Compressive Resistance</u> <u>Design Bearing</u> using dynamic testing only where pile resistance contribution above this elevation shall not be considered.
  
'''(E2.23) (Use when static test piles are required.) This number of piles in table should not include test piles. If test piles are specified, place an * beside the number of piles at the bents indicated.'''
+
'''(E2.23) (Use when static test piles are required.) The number of piles in table should not include probe piles. If probe piles are specified, place an * beside the number of piles at the bents indicated.'''
:&nbsp;*One concrete test piles shall be driven in permanent position, one for each bents, at Bents No. <u> &nbsp;  &nbsp;  &nbsp;  </u> and <u> &nbsp;  &nbsp;  &nbsp;  </u>.
+
:&nbsp;*One concrete probe pile shall be driven in permanent position, one for each bent, at Bents No. <u> &nbsp;  &nbsp;  &nbsp;  </u> and <u> &nbsp;  &nbsp;  &nbsp;  </u>.
 
   
 
   
'''(E2.24) (Use when CIP piles are used in Seismic Performance Categories B, C, or D.)'''
+
'''(E2.24) '''  
:Fluted type cast-in-place pile shall not be permitted.
+
:All piles shall be galvanized down to the minimum galvanized penetration (elevation).
  
'''(E2.25) (Use for LFD piling design when Design Bearing is determined from service loads and shown on the plans. This represents converting the Design Bearing to a Minimum Nominal Axial Compressive Resistance, P, for use in the dynamic formula in accordance with Sec 702. Example: Considered only for widenings, repairs and rehabilitations.)'''
+
'''(E2.25) (Use for all HP pile and when pile point reinforcement is required for CIP pile.)'''
 +
:Pile point reinforcement need not be galvanized. Shop drawings will not be  required for pile point reinforcement.
 +
<div id="(E2.26)"></div>
 +
'''(E2.26) (Use for LFD piling design when Design Bearing is determined from service loads and shown on the plans. See guidance on <font color="purple">[MS Cell] (E2.1)</font color="purple"> for specific pile driving verification method. Example: Considered only for widenings, repairs and rehabilitations.) '''
  
:All  piling shall be driven to a minimum nominal axial compressive resistance equal to 3.5 times the Design Bearing as shown on the plans.
+
:All  piling shall be driven to a minimum nominal axial compressive resistance equal to <u>3.5</u> <u>2.75</u> <u>2.25</u> <u>2.00</u> times the Design Bearing as shown on the plans.
 +
<div id="(E2.27)"></div>
 +
'''(E2.27) Use for galvanized piles.'''
  
<div id="Drilled Shafts"></div>
+
:The contractor shall make every effort to achieve the minimum galvanized penetration (elevation) shown on the plans for all piles.  Deviations in penetration less than 5 feet of the minimum will be considered acceptable provided the contractor makes the necessary corrections to ensure the minimum penetration is achieved on subsequent piles.
 +
 
 +
<div id="Drilled Shafts"></div>
 
'''Drilled Shafts'''
 
'''Drilled Shafts'''
  
'''(E2.29)'''
+
'''(E2.29) Include underlined portion when a minimum thickness is required and shown on the plans as minimum.'''
 
:Thickness of permanent steel casing shall be <u>as shown on the plans and</u> in accordance with Sec 701.
 
:Thickness of permanent steel casing shall be <u>as shown on the plans and</u> in accordance with Sec 701.
  
 
'''(E2.30) Note may not be required with drilled shafts for high mast tower lighting.'''
 
'''(E2.30) Note may not be required with drilled shafts for high mast tower lighting.'''
:An additional 4 feet has been added to V-bar lengths and an additional __-#__-P-bars have been added in the quantities, if required, for possible change in drilled shaft or rock socket length. The additional V-bar length shall be cut off or included in the reinforcement lap if not required. The additional P-bars shall be spaced similarly to that shown in elevation, if required, or to a lesser spacing if not required, but not less than 6" cts.
+
:An additional 4 feet has been added to V-bar lengths and additional __-#_-P___ bars have been added in the quantities, if required, for possible change in drilled shaft or rock socket length. The additional V-bar length shall be cut off or included in the reinforcement lap if not required. The additional P bars shall be spaced similarly to that shown in elevation, if required, or to a lesser spacing if not required, but not less than 6-inch centers.
  
 
'''(E2.31) Note not required with drilled shafts for high mast tower lighting. '''
 
'''(E2.31) Note not required with drilled shafts for high mast tower lighting. '''
Line 1,211: Line 1,365:
  
 
'''(E3.2) <font color="purple">[MS Cell]</font color="purple"> (Place on Front Sheet of the plans when boring data is  provided for bridges, retaining walls, MSE walls and any other structure.)'''
 
'''(E3.2) <font color="purple">[MS Cell]</font color="purple"> (Place on Front Sheet of the plans when boring data is  provided for bridges, retaining walls, MSE walls and any other structure.)'''
:[[Image:751.50 boring location mark.gif]] Indicates location of borings.<br/>'''Notice and Disclaimer Regarding Boring Log Data'''<br/>The locations of all subsurface borings for this structure are shown on the  plan sheet(s) for this structure.  The boring data for all locations indicated, as well as any other boring logs or other factual records of subsurface data and investigations performed by the department for the design of the project, are shown on Sheet(s) No.___ or will be available from the Project Contact upon written request.  No greater significance or weight should be given to the boring data depicted on the plan sheets than is given to the subsurface data available from the district or elsewhere.<br/>&nbsp;<br/>The Commission does not represent or warrant that any such boring data accurately depicts the conditions to be encountered in constructing this project.  A contractor assumes all risks it may encounter in basing its bid prices, time or schedule of performance on the boring data depicted here or those available from the district, or on any other documentation not expressly warranted, which the contractor may obtain from the Commission.
+
:[[Image:751.50 E3.2 boring.jpg|12px]] Indicates location of borings.<br/>'''Notice and Disclaimer Regarding Boring Log Data'''<br/>The locations of all subsurface borings for this structure are shown on the  plan sheet(s) for this structure.  The boring data for all locations indicated, as well as any other boring logs or other factual records of subsurface data and investigations performed by the department for the design of the project, are shown on Sheet(s) No.___ and may be included in the Electronic Bridge Deliverables. They will also be available from the Project Contact upon written request.  No greater significance or weight should be given to the boring data depicted on the plan sheets than is given to the subsurface data available from the district or elsewhere.<br/>&nbsp;<br/>The Commission does not represent or warrant that any such boring data accurately depicts the conditions to be encountered in constructing this project.  A contractor assumes all risks it may encounter in basing its bid prices, time or schedule of performance on the boring data depicted here or those available from the district, or on any other documentation not expressly warranted, which the contractor may obtain from the Commission.
  
 
'''(E3.4) (Place on the Boring Data Sheet)'''
 
'''(E3.4) (Place on the Boring Data Sheet)'''
 
:For location of borings see Sheet(s) No. <u> &nbsp; </u>.
 
:For location of borings see Sheet(s) No. <u> &nbsp; </u>.
 +
<div id="Final clearance - Bridges over Railroads"></div>
 +
'''Final clearance - Bridges over Railroads'''
  
 +
'''(E3.5) In the general elevation detail, the vertical clearance dimension callout shall be the following asterisked note placed near the detail. '''
  
'''Final clearance - Bridges over railroads'''
+
: <math>\, *</math> Final vertical clearance from top of rails to bottom of superstructure shall be <u> &nbsp; (1) &nbsp;</u> minimum. Track elevations should be verified in the field prior to construction to determine if the final vertical clearance shown will be obtained.
 
+
::(1) Required clearance specified on the Bridge Memorandum.
'''(E3.5) Place an (<math>\, *</math>) in the vertical clearance dimension and the following note on the front sheet of bridge plans.'''
 
:(<math>\, *</math>) Final vertical clearance from top of rails to bottom of superstructure shall be at least <math>\, **</math>. Track elevations should be verified in the field prior to construction to determine if the final vertical clearance shown will be obtained.
 
 
 
:<math>\, **</math> Clearance specified on the Design Layout (23'-0" min.).
 
 
 
  
 
'''Seal Course (Use the following notes when Seal Course is specified on the Design Layout.)'''
 
'''Seal Course (Use the following notes when Seal Course is specified on the Design Layout.)'''
Line 1,236: Line 1,388:
 
'''Bar placement in slabs''' (Notes E3.8 – E3.9)
 
'''Bar placement in slabs''' (Notes E3.8 – E3.9)
  
'''Guidance Notes for Detailing:''' Indicate only the top longitudinal slab bars affected for tying the R4 barrier curb bar. It may be that only one bar needs to be indicated for shifting.  
+
'''Guidance Notes for Detailing:''' Indicate only the top longitudinal slab bars affected for tying the R4 barrier bar. It may be that only one bar needs to be indicated for shifting.  
  
 
'''(E3.8) Use note with detail drawing indicating which bars are to be shifted.'''
 
'''(E3.8) Use note with detail drawing indicating which bars are to be shifted.'''
Line 1,270: Line 1,422:
  
 
'''(G1.3)'''
 
'''(G1.3)'''
:<u>Safety barrier curbs</u>, <u>parapets</u> <u>and</u> <u>end post</u> shall not be poured until the slab has been poured in the adjacent span.
+
:<u>Barrier</u>, <u>parapets</u> <u>and</u> <u>end post</u> shall not be poured until the slab has been poured in the adjacent span.
  
  
Line 1,283: Line 1,435:
  
 
'''(G1.6) Add to sheet showing the typical section thru wing detail.'''
 
'''(G1.6) Add to sheet showing the typical section thru wing detail.'''
:For reinforcement of the safety barrier curb, see Sheet No. <u> &nbsp; &nbsp; </u> (1).
+
:For reinforcement of the barrier, see Sheet No. <u> &nbsp; &nbsp; </u> (1).
  
::(1) Use sheet number of the details of the safety barrier curb at end bents.
+
::(1) Use sheet number of the details of the barrier at end bents.
  
  
 
'''Integral End Bents (G1.7 thru G1.10)'''
 
'''Integral End Bents (G1.7 thru G1.10)'''
  
'''(G1.7) Second F bar required for skewed bents.'''
+
'''(G1.7) Place with part plan of end bent, second F bar required for skewed bents. '''
:The #6-F<u> &nbsp; &nbsp; </u><font color = "white">a</font color="white"> <u>and #6-F &nbsp; </u>  bars shall be bent in the field to clear <u>beams</u> <u>girders</u>.  
+
:The #6-F___ <u>and #6-F &nbsp; </u>  bars shall be bent in the field to clear <u>beams</u> <u>girders</u>.  
 
<div id="(G1.7.1) Use for skewed bents."></div>
 
<div id="(G1.7.1) Use for skewed bents."></div>
  
'''(G1.7.1) Use for skewed bents. The #5-H bars are the approach slab anchorage (L shaped) bars embedded 12” (Min.) @ 90⁰ into the end bent. Modify note as needed when bent details are on multiple sheets. '''
+
'''(G1.7.1) Use for skewed bents. Place with plan of beam showing reinforcement and part plan of end bent, V bars not required with part plan of end bent. '''
:The U bars, Pairs-V bars and #5-H<u> &nbsp; &nbsp; </u> bars shall be placed parallel to centerline of roadway.
+
:The U bars <u>and pairs of V bars</u> shall be placed parallel to centerline of roadway.
  
'''(G1.8)'''
+
'''(G1.8) Place with part plan of end bent.'''
 
:All concrete in the end bent above top of beam and below top of slab shall be Class B-2.
 
:All concrete in the end bent above top of beam and below top of slab shall be Class B-2.
  
'''(G1.8.1) Use for detached wing walls when Reinforcing Steel (Epoxy Coated) is not listed in the Estimated Quantities.'''
+
'''P/S Structures (G1.9 and G1.9.1). place with part plan of end bent.'''
:The top two epoxy bars in the detached wing walls shall be included with the Superstructure Quantities for <u>Slab on Steel</u> <u>Slab on Concrete I-Girder</u> <u>Slab on Concrete Bulb-Tee Girder</u> <u>Slab on Concrete NU-Girder</u> <u>Slab on Concrete Beam</u> <u>Reinforced Concrete Slab Overlay</u>.
 
  
'''(G1.9) Use for P/S structures.'''
+
'''(G1.9) '''
:Strands at end of the <u>girders</u> <u>beams</u> shall be field bent or, if necessary, cut in field to maintain 1 1/2" minimum clearance to fill face of end bent.
+
:Strands at end of the <u>girders</u> <u>beams</u> shall be field bent or, if necessary, cut in field to maintain 1 1/2-inch minimum clearance to fill face of end bent.
  
 +
'''(G1.9.1) Use appropriate girder sheet number. Use underlined part for Bulb-Tee girders and NU-girders.'''
 +
:For location of coil tie rods<u>, #6-H_ (thru gdr. web)</u> and #5-H__(strand tie bar), see Sheet No.___.
  
 
'''(G1.10) Use for steel structures without steel diaphragms at end bents.'''
 
'''(G1.10) Use for steel structures without steel diaphragms at end bents.'''
Line 1,334: Line 1,487:
  
 
:Holes for anchor bolts may be drilled into the substructure.  
 
:Holes for anchor bolts may be drilled into the substructure.  
 
'''(G1.15C) Use for substructure at open expansion device locations, galvanized corrugated steel pipe is not allowed.'''
 
 
:Anchor bolt wells shall not be formed with galvanized corrugated steel pipe.
 
  
  
 
'''Beam/Girder Chairs (G1.16 thru G1.19). Notes G1.16 and G1.17 shall be placed near chair details. '''
 
'''Beam/Girder Chairs (G1.16 thru G1.19). Notes G1.16 and G1.17 shall be placed near chair details. '''
 
+
<div id="(G1.16)"></div>
 
'''(G1.16)'''
 
'''(G1.16)'''
 
:Cost of furnishing, fabricating and installing chairs will be considered completely covered by the contract unit price for <u>(a)</u>.
 
:Cost of furnishing, fabricating and installing chairs will be considered completely covered by the contract unit price for <u>(a)</u>.
Line 1,375: Line 1,524:
 
Reinforcing steel shall be shifted to clear chairs. <u>For details of chairs, see Sheet No. &nbsp;  </u>.  
 
Reinforcing steel shall be shifted to clear chairs. <u>For details of chairs, see Sheet No. &nbsp;  </u>.  
  
'''All Substructure Sheets with Pile Cap Bents. '''
+
'''Pile Cap Bents. '''
 +
 
 +
'''(G1.20) Place with plan showing reinforcement.'''
 +
:Reinforcing steel shall be shifted to clear piles. U bars shall clear piles by at least 1 1/2 inches. 
 +
 
 +
'''Vertical Drains at End Bents.'''
 +
 
 +
'''(G1.25) Place with part plan of end bent. '''
 +
:For details of vertical drain at end bent, see Sheet No.___.
 +
 
 +
'''Bridge Approach Slab. '''
 +
 
 +
'''(G1.30) Place with part plan of end bent.'''
 +
:For details of bridge approach slab, see Sheet No.___.
  
'''(G1.20) '''
 
:Reinforcing steel shall be shifted to clear piles. U bars shall clear piles by at least 1 1/2". 
 
  
 
'''Miscellaneous (G1.41 thru G1.43) '''
 
'''Miscellaneous (G1.41 thru G1.43) '''
  
'''(G1.40)  Use the following note at all fixed intermediate bents on prestressed girder bridges with steps of 2" or more.'''
+
'''(G1.40)  Use the following note at all fixed intermediate bents on prestressed girder bridges with steps of 2" or more. Place with plan of beam.'''
:For steps 2" or more, use 2 1/4" x 1/2" joint filler up vertical face.
+
:For steps 2 inches or more, use 2 1/4 x 1/2 inch joint filler up vertical face.
 +
 
 +
'''(G1.41a) Use the following note when vertical column steel is hooked into the bent beam for seismic category A.'''
 +
:At the contractor's option, the hooks of vertical bars embedded in the beam cap may be oriented inward or outward.
  
'''(G1.41) Use the following note when vertical column steel is hooked into the bent beam.'''
+
'''(G1.41b) Use the following note when vertical column steel is hooked into the bent beam for seismic category B, C or D. '''
:At the contractor's option, the hooks of V-Bars embedded in the beam cap may be oriented inward or outward for Seismic Category A.  Bending the hook outward, away from the column core, is not allowed for Seismic Category B, C, or D.
+
:The hooks of vertical bars embedded in the beam cap shall not be turned outward, away from the column core.
  
 
'''(G1.42)  Place the following note on plans when using Optional Section for Column-Web beam joints.'''
 
'''(G1.42)  Place the following note on plans when using Optional Section for Column-Web beam joints.'''
Line 1,393: Line 1,556:
 
'''(G1.43)  Place the following note on plans when you have adjoining twin bridges.'''
 
'''(G1.43)  Place the following note on plans when you have adjoining twin bridges.'''
 
:Preformed compression joint seal shall be in accordance with Sec 717. Payment will be considered completely covered by the contract unit price for other items included in the contract.
 
:Preformed compression joint seal shall be in accordance with Sec 717. Payment will be considered completely covered by the contract unit price for other items included in the contract.
 +
 +
'''G1.44 Use with column closed circular stirrup/tie bar detail.'''
 +
 +
:Minimum lap ____ (Stagger adjacent bar splices)
  
 
=== G2. Deadman Anchors ===
 
=== G2. Deadman Anchors ===
Line 1,437: Line 1,604:
 
:Note: Reinforcing steel lengths are based on nominal lengths, out to out.
 
:Note: Reinforcing steel lengths are based on nominal lengths, out to out.
  
=== G3. Vertical Drain at End Bent ===
+
=== G3. Vertical Drain at End Bent (Notes for Bridge Standard Drawings)===
  
 +
'''(G3.0) '''
 +
:All drain pipe shall be sloped 1 to 2 percent.
  
 
'''(G3.1)'''
 
'''(G3.1)'''
Line 1,444: Line 1,613:
  
 
'''(G3.2)'''
 
'''(G3.2)'''
:Place drain pipe at fill face of end bent and slope to lowest grade of ground line, also missing the lower beam of end bent by 1 1/2 inches. (See Elevation at End Bent.)
+
:Drain pipe shall be placed at fill face of end bent and inside face of wings.  The pipe shall slope to lowest grade of ground line, also missing the lower beam of end bent by a minimum of 1 1/2 inches.
  
 
'''(G3.3)'''
 
'''(G3.3)'''
:Perforated pipe shall be placed at fill face side at the bottom of end bent and plain pipe shall be used where the vertical drain ends to the exit at ground line.
+
:Perforated pipe shall be placed at fill face side and inside face of wings at the bottom of end bent and plain pipe shall be used where the vertical drain ends to the exit at ground line.
  
 
=== G4. Substructure Quantity Table ===
 
=== G4. Substructure Quantity Table ===
  
'''(G4.1) <font color="purple">[MS Cell]</font color="purple">'''
+
'''(G4.1) <font color="purple">[MS Cell]</font color="purple">''' Place substructure quantity table on right side of substructure bent sheet.
 
:{|border="0" style="text-align:center;" cellpadding="5" cellspacing="0"
 
:{|border="0" style="text-align:center;" cellpadding="5" cellspacing="0"
 
|-
 
|-
Line 1,487: Line 1,656:
  
 
'''(G4.2)'''
 
'''(G4.2)'''
:Note:  These quantities are included in the estimated quantities table on Sheet No. <u>&nbsp;&nbsp;</u>.
+
:These quantities are included in the estimated quantities table on Sheet No. <u>&nbsp;&nbsp;</u>.
  
'''Note to Detailer:'''<br/>Place substructure quantity table on right side of substructure bent sheet.
+
'''Drilled Shafts'''
  
=== G5. 20" and 24" CIP Piles ===
+
'''(G4.3) '''
 +
:All reinforcement in drilled shafts and rock sockets is included in the substructure quantities.
  
'''(Do not use without approval of Structural Project Manager or Liaison)'''
 
  
'''(G5.1)'''
+
=== G5. CIP Concrete Piles (Notes for Bridge Standard Drawings)===
:All concrete for cast-in-place piles shall be Class B-1.
 
  
'''(G5.2)'''
 
:The minimum wall thickness of any spot or local area of any type shall not be more than 12.5% under the specified nominal wall thickness.
 
  
'''(G5.3)'''
+
====G5a Closed Ended Cast-in Place (CECIP) Concrete Pile====
:Closure plates shall be required for tips of pipe piles and shall not project beyond the outside diameter of the pipe piles.  Satisfactory weldments may be made by beveling tip ends of pipe or by use of inside backing rings.  In either case, proper gaps shall be used to obtain weld penetration full thickness of pipe. Payment for furnishing and installing closure plates will be considered completely covered by the contract unit price for Cast-in-Place Concrete Piles.
 
  
'''(G5.4)'''
+
'''(G5a1)'''
:Splice details for cast-in-place concrete piles shall be in accordance with the manufacturer's recommendations.
+
:Welded or seamless steel shell (pipe) shall be ASTM A252 Grade 3 (fy = 45,000 psi).
  
'''(G5.5)'''
+
'''(G5a2)'''
:All splices of shells for cast-in-place concrete piles shall be made watertight and to the full strength of the shell above and below the splice to permit hard driving without damage.  All shells damaged during driving shall be replaced without cost to the State.  Shell sections used for splicing shall be at least 5'-0" in length.  The splice at the tapered section shall  be at least 3'-0" below the streambed for intermediate trestle type bents.
+
:Concrete for cast-in-place pile shall be Class B-1.
  
===G6. As-Built Pile and Drilled Shaft Data===
+
'''(G5a3)'''
 +
:Steel for closure plate shall be ASTM A709 Grade 50.
  
'''(G6.1) Include A, B and C with all pile types. Include D and E along with bracketed guidance when piles are being dynamic tested.'''  
+
'''(G5a4)'''
 +
:Steel for cruciform pile point reinforcement shall be ASTM A709 Grade 50.
  
:Indicate in remarks column:
+
'''(G5a5)'''
 +
:Steel casting for conical pile point reinforcement shall be <u>ASTM A27 Grade 65-35</u> <u>ASTM A148 Grade 90-60</u>.
  
:A. Pile type and grade
+
'''(G5a6)'''
 +
:The minimum wall thickness of any spot or local area of any type shall not be more than 12.5% under the specified nominal wall thickness.  
  
:B. Batter
+
'''(G5a7)'''
 +
:Closure plate shall not project beyond the outside diameter of the pipe pile. Satisfactory weldments may be made by beveling tip end of pipe or by use of inside backing rings. In either case, proper gaps shall be used to obtain weld penetration full thickness of pipe. Payment for furnishing and installing closure plate will be considered completely covered by the contract unit price for Galvanized Cast-In-Place Concrete Piles.
  
:C. Driven to practical refusal
+
'''(G5a8)'''
 +
:Splices of pipe for cast-in-place concrete pile shall be made watertight and to the full strength of the pipe above and below the splice to permit hard driving without damage. Pipe damaged during driving shall be replaced without cost to the state. Pipe sections used for splicing shall be at least 5 feet in length.
  
:D. PDA test pile
+
'''(G5a9a) Use the following note for seismic category A'''
 +
:At the contractor's option, the hooks of vertical bars embedded in the beam cap may be oriented inward or outward.
  
:E. Minimum tip elevation controlled
+
'''(G5a9b) Use the following note for seismic category B, C or D '''
 +
:The hooks of vertical bars embedded in the beam cap should not be turned outward, away from the pile core.
  
:(Use when actual blow count is less than PDA blow count due to minimum tip elevation requirement.  A plus sign (+) shall be placed after the PDA nominal axial compressive resistance value indicating actual value is higher than PDA value.)
+
'''(G5a10)'''
 +
:The hooks of vertical bars embedded in the pile cap footing should be oriented outward for all seismic categories.
  
'''(G6.2) Use this note when only drilled shafts are shown on the sheet. '''
+
'''(G5a11)'''  
 +
:Closure plate need not be galvanized.
  
:Indicate remarks in the remarks column.
+
'''(G5a12) '''
 +
:Reinforcing steel for cast-in-place pile is included in the Bill of Reinforcing Steel.  
  
'''(G6.3) '''
+
'''(G5a13) '''
 +
:All reinforcement for cast-in-place pile is included in the estimated quantities for bents.
  
:This sheet to be completed by MoDOT construction personnel.
+
'''(G5a14) '''
 +
:The contractor shall determine the pile wall thickness required to avoid damage from all driving activities, but wall thickness shall not be less than the minimum specified.  No additional payment will be made for furnishing a thicker pile wall than specified on the plans.
  
== H. Superstructure Notes ==
 
  
  
=== H1. Steel ===
+
====G5b Open Ended Cast-in Place (OECIP) Concrete Pile====
  
'''Plate Girders - (Shop welding)'''
+
'''(G5b1)'''
 +
:Welded or seamless steel shell (pipe) shall be ASTM A252 Grade 3 (fy = 45,000 psi).
 +
 +
'''(G5b2)'''
 +
:Open ended pile shall be augered out to the minimum pile cleanout penetration elevation and filled with Class B-1 concrete.
  
'''(H1.1) To be used only with the permission of the Structural Project Manager.'''
+
'''(G5b3)'''
:By approval of the engineer, the contractor may omit any shop flange splice by extending the heavier flange plate and providing approved modifications of details at field flange splices and elsewhere as required.  All cost of any required design, plan revisions or re-checking of shop drawings shall be borne by the contractor.  Payweight in any case will be based on material shown on Design Plans.
+
:Concrete for cast-in-place pile shall be Class B-1.
  
 +
'''(G5b4)'''
 +
:Steel casting for open ended cutting shoe pile point reinforcement shall be <u>ASTM A27 Grade 65-35</u> <u>ASTM A148 Grade 90-60</u>.
  
'''Welded Shop Splices'''
+
'''(G5b5)'''
 +
:The minimum wall thickness of any spot or local area of any type shall not be more than 12.5% under the specified nominal wall thickness.
  
'''(H1.1.1) Place near Welded Shop Splice Details.'''
+
'''(G5b6)'''
:Welded shop web and flange splices may be permitted when detailed on the shop drawings and approved by the engineer. No additional payment will be made for optional welded shop web and flange splices.
+
:Splices of pipe for cast-in-place pipe pile shall be made watertight and to the full strength of the pipe above and below the splice to permit hard driving without damage. Pipe damaged during driving shall be replaced without cost to the state. Pipe sections used for splicing shall be at least 5 feet in length.  
  
'''(H1.2) <font color="purple">[MS Cell]</font color="purple">'''
+
'''(G5b7a) Use the following note for seismic category A'''
:[[Image:751.50 circled 2.gif]] Weld to compression flange as located on the elevations of girder.
+
:At the contractor's option, the hooks of vertical bars embedded in the beam cap may be oriented inward or outward.
<div id="(H1.3) Add to note (H1.2)"></div>
 
  
'''(H1.3) Add to note (H1.2), only when girders are built up with A514 or A517 steel flanges. Caution: Using this note means that these structural steels are already on the system. Any new construction using these structural steels requires permission of the State Bridge Engineer. Any construction involving these structural steels requires notification to the State Bridge Engineer.'''
+
'''(G5b7b) Use the following note for seismic category B, C or D'''
 +
:The hooks of vertical bars embedded in the beam cap should not be turned outward, away from the pile core.
  
:Intermediate web stiffeners shall not be welded to plates of A514 or A517 steel.
+
'''(G5b8)'''
 +
:The hooks of vertical bars embedded in the pile cap footing should be oriented outward for all seismic categories.
  
 +
'''(G5b9)'''
 +
:Reinforcing steel for cast-in-place pile is included in the Bill of Reinforcing Steel.
  
'''Plate Girders with Camber'''
+
'''(G5b10)'''
 +
:All reinforcement for cast-in-place pile is included in the estimated quantities for bents.
  
'''(H1.4) Place near the elevation of girder.'''
+
'''(G5b11)'''
:Plate girders shall be fabricated to be in accordance with the camber diagram shown on Sheet No. <u>&nbsp;&nbsp;</u>.
+
:The contractor shall determine the pile wall thickness required to avoid damage from all driving activities, but wall thickness shall not be less than the minimum specified.  No additional payment will be made for furnishing a thicker pile wall than specified on the plans.
  
  
'''Detail Camber Diagram with note (H1.5), Dead Load Deflection Diagram with notes (H1.6) and (H1.6.1), and Theoretical Slab Haunch with note (H1.7).'''
+
===G6. As-Built Pile and Drilled Shaft Data===
  
'''(H1.5)'''
+
'''(G6.1) Include A, B and C with all pile types. Include D and E along with bracketed guidance when piles are being dynamic tested.'''
:Camber includes allowance for <u>vertical curve,</u> <u>superelevation transition,</u>  <u>and for</u> dead load deflection due to concrete slab, <u>curb,</u> <u>asphalt,</u> <u>concrete wearing surface</u> and structural steel.
 
  
'''(H1.6)'''
+
:Indicate in remarks column:
:<u>&nbsp;&nbsp;</u>% of dead load deflection is due to the weight of structural steel.
 
  
'''(H1.6.1)'''
+
:A. Pile type and grade
:Dead load deflection includes weight of structural steel, concrete slab, <u>and barrier curb</u>.
 
  
 +
:B. Batter
  
'''(H1.7)'''
+
:C. Driven to practical refusal
:<u>&nbsp;&nbsp;&nbsp;&nbsp;</u> dimensions may vary if the girder camber after erection differs from plan camber by more or less than the % of Dead Load Deflection due to weight of structural steel.  No payment will be made for any adjustment in forming or additional concrete required for variation in haunching.
 
  
'''Note:''' Increase the haunch by 1/2"&plusmn; more than what is required to make one size shear connector work for both the C.I.P. and the S.I.P. Options.
+
:D. PDA test pile
  
 +
:E. Minimum tip elevation controlled
  
'''Bolted Field Splices for Plate Girders and Wide Flange Beams (All Structural Steel including Weathering Steel)'''
+
:(Use when actual blow count is less than PDA blow count due to minimum tip elevation requirement.  A plus sign (+) shall be placed after the PDA nominal axial compressive resistance value indicating actual value is higher than PDA value.)
  
'''Place the following notes near detail of bolted field splice:'''
+
'''(G6.2) Use this note when only drilled shafts are shown on the sheet. '''
  
'''(H1.8)'''
+
:Indicate remarks in the remarks column.
:Contact surfaces shall be in accordance with Sec 1081 for surface preparation.
 
  
'''(H1.8.1)'''
+
'''(G6.3) '''
:Use 7/8ӯ high strength bolts with 15/16ӯ holes.
 
  
 +
:This sheet to be completed by MoDOT construction personnel.
  
'''Structures without Longitudinal Section'''
+
===G7. Steel HP Pile===
  
'''(H1.9) Place just above slab at part section near end diaphragm and draw an arrow to the top of diaphragm.'''
+
'''(G7.1) <font color="purple">[MS Cell]</font color="purple"> Use with Pile Splice Detail - Galvanized.'''
:Haunch slab to bear.
+
:Galvanizing material shall be omitted or removed one inch clear of weld locations in accordance with [https://www.modot.org/media/20575 Sec 702].
  
 +
'''(G7.2) <font color="purple">[MS Cell]</font color="purple"> Use with Pile Seismic Anchor Detail – Galvanized.'''
 +
:Galvanizing angles, bolts, washers and nuts will not be required.
 +
<div id="(G7.4) (Use the following note"></div>
 +
'''(G7.3) Use on all plans where HP piles are anticipated to be driven to refusal on rock at any depth.'''
  
'''Top of End Bent Backwall (Without expansion device)'''
+
:HP piles are anticipated to be driven to refusal on rock. Review all borings for depth of rock and restrict driving as appropriate to comply with hard rock driving criteria in accordance with [https://www.modot.org/media/20575 Sec 702].
  
'''(H1.10)'''
+
== H. Superstructure Notes ==
:Two layers of 30-lb roofing felt.
 
  
  
'''Section thru Spans'''
+
=== H1. Steel ===
  
'''(H1.11) Place on the slab sheet when applicable.'''
+
'''Plate Girders - (Shop welding)'''
:For details of <u>safety barrier curb</u> <u>parapet</u> <u>median bridge rail</u> not shown, see Sheet No. <u>&nbsp;&nbsp;</u>.
 
  
 +
'''(H1.1) To be used only with the permission of the Structural Project Manager.'''
 +
:By approval of the engineer, the contractor may omit any shop flange splice by extending the heavier flange plate and providing approved modifications of details at field flange splices and elsewhere as required.  All cost of any required design, plan revisions or re-checking of shop drawings shall be borne by the contractor.  Payweight in any case will be based on material shown on Design Plans.
  
'''Web Stiffeners'''
 
  
'''(H1.12)'''
+
'''Welded Shop Splices'''
:Whenever longitudinal stiffeners interfere with bolting the <u>diaphragms</u> <u>cross frames</u> in place, clip stiffeners.
 
  
'''(H1.13)'''
+
'''(H1.1.1) Place near Welded Shop Splice Details.'''
:Longitudinal web stiffeners shall be placed on the outside of exterior girders and on the side opposite of the transverse web stiffener plates for interior girders.
+
:Welded shop web and flange splices may be permitted when detailed on the shop drawings and approved by the engineer.  No additional payment will be made for optional welded shop web and flange splices.
  
'''(H1.14)'''
+
'''(H1.2) Use for the welded connection of intermediate web stiffener to compression flange and intermediate diaphragm connection plate to compression flange.'''
:Transverse web stiffeners shall be located as shown in the plan of structural steel.
+
:(2) Weld to compression flange as located on Elevation of Girder.  
  
'''(H1.15)'''
+
<div id="(H1.3) Add to note (H1.2)"></div>
:Intermediate web stiffener plate and diaphragm spacing may vary from plan dimensions by a maximum of 3" for diaphragm to connect to the intermediate web stiffener plate.
 
  
 +
'''(H1.3) Add to note (H1.2), only when girders are built up with A514 or A517 steel flanges. Caution: Using this note means that these structural steels are already on the system. Any new construction using these structural steels requires permission of the State Bridge Engineer. Any construction involving these structural steels requires notification to the State Bridge Engineer.'''
  
'''Wide Flange Beams - (Shop Welding)'''
+
:Intermediate web stiffeners shall not be welded to plates of A514 or A517 steel.
  
'''(H1.16) To be used only with permission of the Structural Project Manager.'''
 
:By approval of the engineer, the contractor may omit any shop splice by extending the heavier beam and providing an approved modification of details at the field splices.  All costs of any required redesign, plan revisions or rechecking of shop drawings shall be borne by the contractor.  Payweight in any case will be based on material shown on the design plans.
 
  
 +
'''Plate Girders with Camber'''
  
'''Shear Connectors'''
+
'''(H1.4) Place near the elevation of girder.'''
 +
:Plate girders shall be fabricated to be in accordance with the camber diagram shown on Sheet No. <u>&nbsp;&nbsp;</u>.
  
'''(H1.17)  Use only when "Fabricated Structural …Steel… " is included as a pay item.'''
 
:Weight of <u>&nbsp;&nbsp;&nbsp;</u> pounds of shear connectors is included in the weight of Fabricated Structural <u>&nbsp;&nbsp;&nbsp;</u> Steel.
 
  
'''(H1.18)'''
+
'''Detail Camber Diagram with note (H1.5), Dead Load Deflection Diagram with notes (H1.6) and (H1.6.1), and Theoretical Slab Haunch with note (H1.7).'''
:Shear connectors shall be in accordance with Sec 712, 1037 and 1080.
 
  
 +
'''(H1.5)'''
 +
:Camber includes allowance for <u>vertical curve,</u> <u>superelevation transition,</u>  <u>and for</u> dead load deflection due to concrete slab, barrier, <u>asphalt,</u> <u>concrete wearing surface</u> and structural steel.
  
'''Notch Toughness for Wide Flange Beams
+
'''(H1.6)'''
:(Place an <math>\, *</math> with all the beam sizes indicated on the "Plan of Structural Steel".)
+
:<u>&nbsp;&nbsp;</u>% of dead load deflection is due to the weight of structural steel.
:(Place the following note near the "Plan of Structural Steel".)'''
 
  
'''(H1.19)'''
+
'''(H1.6.1)'''
:<math>\, *</math> Notch toughness is required for all wide flange beams.
+
:Dead load deflection includes weight of structural steel, concrete slab, and barrier.
  
  
'''(Place an <math>\, *</math> with the flange plate, pin plate or hanger bar size indicated on the "Detail of Flange Plates, Pin Plate Connection or Hanger Connection".)'''
+
'''(H1.7)'''
 +
:'''*''' Dimension (bottom of slab to top of web)  may vary if the girder camber after erection differs from plan camber by more or less than the % of Dead Load Deflection due to weight of structural steel.  No payment will be made for any adjustment in forming or additional concrete required for variation in haunching.
  
'''(H1.20)'''
+
'''Note:''' Increase the haunch by 1/2"&plusmn; more than what is required to make one size shear connector work for both the CIP and the SIP options.
:<math>\, *</math> Notch toughness is required for all <u>welded flange plates</u> <u>pin plates</u> <u>hanger bars</u>.
 
  
  
'''Notch Toughness for Plate Girders
+
'''Bolted Field Splices for Plate Girders and Wide Flange Beams use Type 3 for weathering steel bolted connections and Type 1 for plain or galvanized steel bolted connections.'''
:'''(Place the following note on the sheet with the Elevation of Girder.)'''
 
:'''(See [[751.5 Structural Detailing Guidelines#751.5.9.3.2 Notch Toughness|Plate Girder Example]] for typical examples for the location of <math>\, ***</math> on details for plate girders.)'''
 
  
'''(H1.21)'''
+
'''Place the following notes near detail of bolted field splice:'''
:<math>\, ***</math> Indicates flange plates subject to notch toughness requirements.
+
<div id="(H1.8) Include underline"></div>
:All web plates shall be subject to notch toughness requirements.
+
'''(H1.8) Include underline portion for Class C or D faying surfaces.  Class B is standard and included in Spec Book 1081.10.3.10.1.'''
 +
 +
:Contact surfaces shall be in accordance with Sec 1081 for surface preparation. <u>The surface condition factor shall be for Class</u> <u>C</u> <u>D</u> <u>with coefficient of</u> <u>0.30.</u> <u>0.45.</u>
  
'''(H1.21.1)'''
+
{|style="padding: 0.3em; margin-left:10px; border:1px solid #a9a9a9; text-align:left; font-size: 95%; background:#f5f5f5" width="780px" align="center"
:The flange and web splice plates shall be subject to notch toughness requirements, when notch toughness is required for flanges on both sides of splice.
+
|-
 +
|colspan="2"|'''Guidance:'''   MoDOT typically uses Class B.
 +
|-
 +
|width="150" valign="top"|Class A Surface: ||Unpainted clean mill scale, and blast-cleaned surfaces with Class A coatings. Surface condition factor = 0.30 (Not used by MoDOT)
 +
|-
 +
|valign="top"|Class B Surface: ||Unpainted blast-cleaned surfaces to SSPC-SP 6 or better, and blast-cleaned surfaces with Class B coatings (inorganic zinc primer), or unsealed pure zinc or 85/15 zinc/aluminum thermal-sprayed coatings with a thickness less than or equal to 16 mils. Surface condition factor = 0.50
 +
|-
 +
|valign="top"|Class C Surface: ||Hot-dip galvanized surfaces. Surface condition factor = 0.30
 +
|-
 +
|valign="top"|Class D Surface:||Blast-cleaned surfaces with Class D coatings (organic zinc-rich primer). Surface condition factor = 0.45
 +
|}
  
 +
'''(H1.8.1)'''
 +
:Bolts shall be 7/8” Ø ASTM F3125 Grade A325 <u>Type 1</u> <u>Type 3</u> in 15/16” Ø holes.
  
'''(Place <math>\, ***</math> near the size of flange splice plates, pin plates or hanger bars and the following note near the detail of flange splice, pin plate connection or hanger connection.)'''
 
  
'''(H1.22)'''
+
'''Structures without Longitudinal Section'''
:<math>\, ***</math> Indicates <u>flange splice plates</u> <u>pin plates</u> <u>hanger bars</u> subject to  notch toughness requirements.
 
  
 +
'''(H1.9) Place just above slab at part section near end diaphragm and draw an arrow to the top of diaphragm.'''
 +
:Haunch slab to bear.
  
'''Structural Steel for Wide Flange Beams and Plate Girder Structures'''
 
  
'''(H1.23)'''
+
'''Top of End Bent Backwall (Without expansion device)'''
:Fabricated structural steel shall be ASTM A709 Grade <u>36</u> <u>50</u>, except as noted.
 
  
 +
'''(H1.10)'''
 +
:Two layers of 30-lb roofing felt.
  
'''Tangent Structures on Straight Grades (Details of Part-Longitudinal Sections at bents and at steel joints will be required on plans.)'''
 
  
'''Plan of Structural Steel and Elevation of Stringers or Girders'''
+
'''Section thru Spans'''
  
'''(H1.24)'''
+
'''(H1.11) Place on the slab sheet when applicable.'''
:Longitudinal dimensions are horizontal from centerline bearing to centerline bearing.
+
:For details of <u>barrier</u> <u>parapet</u> <u>median bridge rail</u> not shown, see Sheet No. <u>&nbsp;&nbsp;</u>.
  
  
'''Oversized Holes for Intermediate Diaphragms'''
+
'''Web Stiffeners'''
 
'''Place the following note near the intermediate diaphragm detail on all tangent wide flange and plate girder structures.'''
 
  
'''(H1.26)'''
+
'''(H1.12)'''
:At the contractor's option, holes in the diaphragm plate of non slab bearing diaphragms may be made 3/16" larger than the nominal diameter of the bolt.  A hardened washer shall be used under the bolt head and nut when this option is used.  Holes in the girder diaphragm connection plate or transverse web stiffener shall be standard size.
+
:Whenever longitudinal stiffeners interfere with bolting the <u>diaphragms</u> <u>cross frames</u> in place, clip stiffeners.
  
 +
'''(H1.13)'''
 +
:Longitudinal web stiffeners shall be placed on the outside of exterior girders and on the side opposite of the transverse web stiffener plates for interior girders.
  
'''Slab drain attachment holes'''
+
'''(H1.14)'''
+
:Transverse web stiffeners shall be located as shown in the plan of structural steel.
'''Place the following note near the Elevation of Girder detail for plate girders or near the plan view for Wide Flange Beams when Slab Drains are used.'''
 
  
'''(H1.27)'''
+
'''(H1.15)'''
:For location of slab drain attachment holes, see slab drain details sheet.
+
:Intermediate web stiffener plate and diaphragm spacing may vary from plan dimensions by a maximum of 3" for diaphragm to connect to the intermediate web stiffener plate.
  
  
'''Tangent Structures on Vertical Curve Grades (Details of part-longitudinal sections at bents and at steel joints will be required on plans for bridges on vertical curves.)'''
+
'''Wide Flange Beams - (Shop Welding)'''
  
'''Plan of Structural Steel'''
+
'''(H1.16) To be used only with permission of the Structural Project Manager.'''
   
+
:By approval of the engineer, the contractor may omit any shop splice by extending the heavier beam and providing an approved modification of details at the field splices. All costs of any required redesign, plan revisions or rechecking of shop drawings shall be borne by the contractor.  Payweight in any case will be based on material shown on the design plans.
'''Dimensions given in plan should be identical to horizontal dimensions detailed in Part-Longitudinal Sections or blocking diagram.'''
 
  
'''(H1.28)'''
 
:Longitudinal dimensions are horizontal from centerline brg. to centerline brg.  See Part-Longitudinal Sections on Sheet No. <u>&nbsp;&nbsp;</u>.
 
  
 +
'''Shear Connectors'''
  
'''Elevation of Constant Depth or Variable Depth Stringers or Girders'''
+
'''(H1.17)  Use only when "Fabricated Structural …Steel… " is included as a pay item.'''
 +
:Weight of <u>&nbsp;&nbsp;&nbsp;</u> pounds of shear connectors is included in the weight of Fabricated Structural <u>&nbsp;&nbsp;&nbsp;</u> Steel.
  
'''(H1.29)'''
+
'''(H1.18)'''
:Longitudinal dimensions are horizontal from centerline brg. to centerline brg. See Part-Longitudinal Sections on Sheet No. <u>&nbsp;&nbsp;</u>.
+
:Shear connectors shall be in accordance with [https://www.modot.org/media/20575 Sec 712, 1037 and 1080].
  
  
'''Horizontally Curved Structures on Straight Grades (Details of Part-Longitudinal Sections at bents and at steel joints will be required on plans.)'''
+
'''Notch Toughness for Wide Flange Beams  (Do not use the following notes if member is labeled as fracture critical.)
+
:(Place an ∗ with all the beam sizes indicated on the "Plan of Structural Steel".)
'''Plan of Structural Steel'''
+
:(Place the following note near the "Plan of Structural Steel".)'''
  
'''(H1.31)'''
+
'''(H1.19)'''
:Longitudinal dimensions are horizontal arc dimensions from centeline brg. to centerline brg.
+
:∗  Notch toughness is required for all wide flange beams.
  
  
'''Horizontally Curved Structures on Straight Grades (Details of Part-Longitudinal Sections at bents and at steel joints will be required on plans.)'''
+
'''(Place an ∗ with the flange plate, pin plate or hanger bar size indicated on the "Detail of Flange Plates, Pin Plate Connection or Hanger Connection".)'''  
 
'''Elevation of Stringers or Girders'''
 
  
'''(H1.32)'''
+
'''(H1.20)'''
:Longitudinal dimensions are horizontal arc dimensions from centerline brg. to centerline brg.
+
:∗  Notch toughness is required for all <u>welded flange plates</u> <u>pin plates</u> <u>hanger bars</u>.
  
  
'''Horizontally Curved Structures on Vertical Curve Grades (Details of part-longitudinal sections at bents and at steel joints will be required on plans for bridges on vertical curves.)'''  
+
'''Notch Toughness for Plate Girders (Do not use the following notes if member is labeled as fracture critical.)
 +
:'''(Place the following note on the sheet with the Elevation of Girder.)'''
 +
:'''(See [[751.5 Structural Detailing Guidelines#751.5.9.3.2 Notch Toughness|Plate Girder Example]] for typical examples for the location of ∗ ∗ ∗ on details for plate girders.)'''
  
'''Plan of Structural Steel'''
+
'''(H1.21)'''
 +
:∗ ∗ ∗  Indicates flange plates subject to notch toughness requirements.
 +
:All web plates shall be subject to notch toughness requirements.
  
'''(H1.36)'''
+
'''(H1.21.1)'''
:Longitudinal dimensions are horizontal arc dimensions from centerline brg. to centerlline brg.  See Part-Longitudinal Sections on Sheet No. <u>&nbsp;&nbsp;</u>.
+
:The flange and web splice plates shall be subject to notch toughness requirements, when notch toughness is required for flanges on both sides of splice.
  
  
'''Elevation of Constant Depth or Variable Depth Stringers or Girders'''
+
'''(Place ∗ ∗ ∗ near the size of flange splice plates, pin plates or hanger bars and the following note near the detail of flange splice, pin plate connection or hanger connection.) '''
  
'''(H1.37)'''
+
'''(H1.22)'''
:Longitudinal dimensions are horizontal arc dimensions from centerline brg. to centerline brg. See Part-Longitudinal Sections on Sheet No. <u>&nbsp;&nbsp;</u>.
+
:∗ ∗ ∗ Indicates <u>flange splice plates</u> <u>pin plates</u> <u>hanger bars</u> subject to  notch toughness requirements.
  
 +
<div id="(H1.23)"></div>
 +
'''(H1.23) Structural Steel for Wide Flange Beams and Plate Girder Structures'''
  
'''Structures on Vertical Curve'''
+
'''(H1.23a)'''
 +
:Fabricated structural steel shall be ASTM A709 Grade <u>36</u> <u>50</u>, except as noted.
  
'''(H1.39)'''
+
'''(H1.23b) Use the following note on all structures that contain non-redundant Fracture Critical Members (FCM).'''
:Elevations shown are at top of web before dead load deflection.
+
Label FCM members in the details, and place the following note nearby.  Notes H1.19 through H1.22 are not required when the member is labeled as fracture critical.
  
 +
:FCM indicates Fracture Critical Member, see [https://www.modot.org/missouri-standard-specifications-highway-construction#page=9 Sec 1080].
  
'''6 x 6 x 3/8  Angle Connection to Top Flange'''
+
'''Tangent Structures on Straight Grades (Details of Part-Longitudinal Sections at bents and at steel joints will be required on plans.)'''
  
'''(H1.40)'''
+
'''Plan of Structural Steel and Elevation of Beams or Girders'''
:The two 3/4"&oslash; high strength bolts that connect the 6 x 6 x 3/8 angle to the top flange shall be placed so the nut is on the inside of flange toward the web.
 
  
 +
'''(H1.24)'''
 +
:Longitudinal dimensions are horizontal from centerline bearing to centerline bearing.
  
'''6 x 6 x 3/8  Angle Connection to Top Flange for Structures on Vertical Curve'''
 
  
'''(H1.40.1)'''
+
'''Oversized Holes for Intermediate Diaphragms'''
:The 6 x 6 x 3/8 angle legs shall be adjusted to the variable angle between bearing stiffener and top flange created by girder tilt due to grade requirements.
+
 +
'''Place the following note near the intermediate diaphragm detail on all tangent wide flange and plate girder structures.'''
  
 +
'''(H1.26)'''
 +
:At the contractor's option, holes in the diaphragm plate of non slab bearing diaphragms may be made 3/16" larger than the nominal diameter of the bolt.  A hardened washer shall be used under the bolt head and nut when this option is used.  Holes in the girder diaphragm connection plate or transverse web stiffener shall be standard size.
  
'''Place the following note near the Plan of Structural Steel for all bridges with stage construction or bridge widening projects.'''
 
  
'''(H1.42)'''
+
'''Slab drain attachment holes'''
:Bolts on intermediate diaphragms and cross frames that connect <u>girders</u> <u>stringers</u> under different construction stage slab pours shall be installed snug tight, then tightened after both adjacent slab pours are completed.
+
 +
'''Place the following note near the Elevation of Girder detail for plate girders or near the plan view for Wide Flange Beams when Slab Drains are used.'''
  
'''(H1.45) Place near detail B and optional detail B with cross frame diaphragms. '''
+
'''(H1.27)'''
:('''*''') At the contractor's option, rectangular fill plates may be used in lieu of diamond fill plates as shown in Optional Detail "B".
+
:For location of slab drain attachment holes, see slab drain details sheet.
  
=== H2. Concrete ===
 
  
 +
'''Tangent Structures on Vertical Curve Grades (Details of part-longitudinal sections at bents and at steel joints will be required on plans for bridges on vertical curves.)'''
  
==== H2a. Continuous Slab ====
+
'''Plan of Structural Steel'''
 +
 +
'''Dimensions given in plan should be identical to horizontal dimensions detailed in Part-Longitudinal Sections or blocking diagram.'''
  
'''(H2a.1) Use for voided slabs'''
+
'''(H1.28)'''
:Tubes for producing voids shall have an outside diameter of [[Image:751.50 circled 1.gif]] and shall be anchored at not more than [[Image:751.50 circled 2.gif]] centersFiber tubes shall have a wall thickness of not less than [[Image:751.50 circled 3.gif]].
+
:Longitudinal dimensions are horizontal from centerline bearing to centerline bearing.  See Part-Longitudinal Sections on Sheet No. <u>&nbsp;&nbsp;</u>.
 +
 
 +
 
 +
'''Elevation of Constant Depth or Variable Depth Beams or Girders'''
 +
 
 +
'''(H1.29)'''
 +
:Longitudinal dimensions are horizontal from centerline bearing to centerline bearing.  See Part-Longitudinal Sections on Sheet No. <u>&nbsp;&nbsp;</u>.
 +
 
 +
 
 +
'''Horizontally Curved Structures on Straight Grades (Details of Part-Longitudinal Sections at bents and at steel joints will be required on plans.)'''
 +
   
 +
'''Plan of Structural Steel'''
 +
 
 +
'''(H1.31)'''
 +
:Longitudinal dimensions are horizontal arc dimensions from centerline bearing to centerline bearing.
 +
 
 +
 
 +
'''Horizontally Curved Structures on Straight Grades (Details of Part-Longitudinal Sections at bents and at steel joints will be required on plans.)'''
 +
 +
'''Elevation of Beams or Girders'''
  
 +
'''(H1.32)'''
 +
:Longitudinal dimensions are horizontal arc dimensions from centerline bearing to centerline bearing.
  
(*) See the following table for [[Image:751.50 circled 1.gif]], [[Image:751.50 circled 2.gif]], & [[Image:751.50 circled 3.gif]].
 
  
:{|border="0" style="text-align:center;" cellpadding="5" cellspacing="0"
+
'''Horizontally Curved Structures on Vertical Curve Grades (Details of part-longitudinal sections at bents and at steel joints will be required on plans for bridges on vertical curves.)'''
|+(Do not show this table on plans)
+
 
!style="border-top:3px solid black; border-bottom:1px solid black; border-left:3px solid black; border-right:1px solid black"|Voids
+
'''Plan of Structural Steel'''
!style="border-top:3px solid black; border-bottom:1px solid black; border-left:1px solid black; border-right:1px solid black"|[[Image:751.50 circled 1.gif]]
+
 
!style="border-top:3px solid black; border-bottom:1px solid black; border-left:1px solid black; border-right:1px solid black"|[[Image:751.50 circled 2.gif]]
+
'''(H1.36)'''
!style="border-top:3px solid black; border-bottom:1px solid black; border-left:1px solid black; border-right:3px solid black"|[[Image:751.50 circled 3.gif]]
+
:Longitudinal dimensions are horizontal arc dimensions from centerline bearing to centerline bearing.  See Part-Longitudinal Sections on Sheet No. <u>&nbsp;&nbsp;</u>.
|-
+
 
|width="75pt" style="border-top:1px solid black; border-bottom:1px solid gray; border-left:3px solid black; border-right:1px solid black"|7"
+
 
|width="50pt" style="border-top:1px solid black; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"|7.0"
+
'''Elevation of Constant Depth or Variable Depth Beams or Girders'''
|width="50pt" style="border-top:1px solid black; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"|4'-0"
+
 
|width="50pt" style="border-top:1px solid black; border-bottom:1px solid gray; border-left:1px solid black; border-right:3px solid black"|0.200"
+
'''(H1.37)'''
|-
+
:Longitudinal dimensions are horizontal arc dimensions from centerline bearing to centerline bearing.  See Part-Longitudinal Sections on Sheet No. <u>&nbsp;&nbsp;</u>.
|width="75pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:3px solid black; border-right:1px solid black"|8"
+
 
|width="50pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"|8.0"
+
 
|width="50pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"|4'-0"
+
'''Structures on Vertical Curve'''
|width="50pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:3px solid black"|0.200"
+
 
|-
+
'''(H1.39)'''
|width="75pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:3px solid black; border-right:1px solid black"|9"
+
:Elevations shown are at top of web before dead load deflection.
|width="50pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"|9.0"
+
 
|width="50pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"|4'-0"
+
 
|width="50pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:3px solid black"|0.200"
+
'''6 x 6 x 3/8  Angle Connection to Top Flange'''
|-
+
 
|width="75pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:3px solid black; border-right:1px solid black"|10"
+
'''(H1.40) Use Type 3 for weathering steel bolted connections and Type 1 for plain or galvanized steel bolted connections.  '''
|width="50pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"|10.0"
+
:Bolts shall be ¾” ø  ASTM F3125 Grade A325 <u>Type 1</u> <u>Type 3</u> that connect the 6 x 6 x 3/8 angle to the top flange and placed so the nut is on the inside of flange toward the web.
|width="50pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"|4'-0"
+
 
|width="50pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:3px solid black"|0.225"
+
 
|-
+
'''6 x 6 x 3/8  Angle Connection to Top Flange for Structures on Vertical Curve'''
|width="75pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:3px solid black; border-right:1px solid black"|11"
+
 
|width="50pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"|11.0"
+
'''(H1.40.1)'''
|width="50pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"|4'-0"
+
:The 6 x 6 x 3/8 angle legs shall be adjusted to the variable angle between bearing stiffener and top flange created by girder tilt due to grade requirements.
|width="50pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:3px solid black"|0.225"
+
 
|-
+
 
|width="75pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:3px solid black; border-right:1px solid black"|12"
+
'''(H1.42) Place the following note near the Plan of Structural Steel for all new bridges with staged construction or bridge widening projects. '''
|width="50pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"|12.0"
+
:Bolts for intermediate diaphragms and cross frames that connect <u>girders</u> <u>beams</u> under different construction staged slab pours shall be installed snug tight, then tightened after both adjacent slab pours are completed.
|width="50pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"|4'-0"
+
 
|width="50pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:3px solid black"|0.225"
+
'''(H1.43) Place the following note on the staging sheet for all bridge redecking projects with staged construction.'''
 +
:Existing <u>bolts</u> <u>rivets</u> on intermediate diaphragms and cross frames that connect <u>girders</u> <u>beams</u> under different construction staged slab pours shall be removed and replaced with new in kind high strength bolts installed snug tight and in accordance with Sec 712. The high strength bolts shall be tightened after both adjacent slab pours are completed. Cost will be considered incidental to other pay items.
 +
 
 +
'''(H1.45) Place near Detail B and Optional Detail B with cross frame diaphragms. '''
 +
:('''*''') At the contractor's option, rectangular fill plates may be used in lieu of diamond fill plates as shown in Optional Detail B.
 +
 
 +
<div id="Deflection and Haunching:"></div>
 +
'''Deflection and Haunching: (Use for wide flange deck replacements.) '''
 +
 
 +
'''(H1.50)'''
 +
:The contractor shall determine dead load deflections and haunching based on field measurements and/or existing bridge plans and these may be adjusted based on the difference between the new and existing dead load weights.
 +
 
 +
'''(H1.51)'''
 +
:Slab is to be considered at a uniform thickness as shown on the plans. Haunching will vary. See front sheet for slab thickness.
 +
 
 +
'''(H1.53) Drip angles''' (Notes for Bridge Standard Drawings)
 +
:'''(H1.53a)''' Drip angles shall be caulked with dark brown caulking against flange, web and fillet welds.
 +
:'''(H1.53b)''' Drip angles shall be same grade as bottom flange.
 +
:'''(H1.53c)''' Use ½” diameter ASTM F3125 Grade A325 Type 3 for bolted connection.
 +
 
 +
=== H2. Concrete ===
 +
 
 +
 
 +
==== H2a. Continuous Slab ====
 +
 
 +
'''(H2a.1) Use for voided slabs'''
 +
:Tubes for producing voids shall have an outside diameter of [[Image:751.50 circled 1.gif]] and shall be anchored at not more than [[Image:751.50 circled 2.gif]] centers.  Fiber tubes shall have a wall thickness of not less than [[Image:751.50 circled 3.gif]].
 +
 
 +
 
 +
(*) See the following table for [[Image:751.50 circled 1.gif]], [[Image:751.50 circled 2.gif]], & [[Image:751.50 circled 3.gif]].
 +
 
 +
:{|border="0" style="text-align:center;" cellpadding="5" cellspacing="0"
 +
|+(Do not show this table on plans)
 +
!style="border-top:3px solid black; border-bottom:1px solid black; border-left:3px solid black; border-right:1px solid black"|Voids
 +
!style="border-top:3px solid black; border-bottom:1px solid black; border-left:1px solid black; border-right:1px solid black"|[[Image:751.50 circled 1.gif]]
 +
!style="border-top:3px solid black; border-bottom:1px solid black; border-left:1px solid black; border-right:1px solid black"|[[Image:751.50 circled 2.gif]]
 +
!style="border-top:3px solid black; border-bottom:1px solid black; border-left:1px solid black; border-right:3px solid black"|[[Image:751.50 circled 3.gif]]
 +
|-
 +
|width="75pt" style="border-top:1px solid black; border-bottom:1px solid gray; border-left:3px solid black; border-right:1px solid black"|7"
 +
|width="50pt" style="border-top:1px solid black; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"|7.0"
 +
|width="50pt" style="border-top:1px solid black; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"|4'-0"
 +
|width="50pt" style="border-top:1px solid black; border-bottom:1px solid gray; border-left:1px solid black; border-right:3px solid black"|0.200"
 +
|-
 +
|width="75pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:3px solid black; border-right:1px solid black"|8"
 +
|width="50pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"|8.0"
 +
|width="50pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"|4'-0"
 +
|width="50pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:3px solid black"|0.200"
 +
|-
 +
|width="75pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:3px solid black; border-right:1px solid black"|9"
 +
|width="50pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"|9.0"
 +
|width="50pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"|4'-0"
 +
|width="50pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:3px solid black"|0.200"
 +
|-
 +
|width="75pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:3px solid black; border-right:1px solid black"|10"
 +
|width="50pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"|10.0"
 +
|width="50pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"|4'-0"
 +
|width="50pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:3px solid black"|0.225"
 +
|-
 +
|width="75pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:3px solid black; border-right:1px solid black"|11"
 +
|width="50pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"|11.0"
 +
|width="50pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"|4'-0"
 +
|width="50pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:3px solid black"|0.225"
 +
|-
 +
|width="75pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:3px solid black; border-right:1px solid black"|12"
 +
|width="50pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"|12.0"
 +
|width="50pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"|4'-0"
 +
|width="50pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:3px solid black"|0.225"
 
|-
 
|-
 
|width="75pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:3px solid black; border-right:1px solid black"|14"
 
|width="75pt" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:3px solid black; border-right:1px solid black"|14"
Line 1,996: Line 2,287:
 
==== H2c. Prestressed Girders and Beams====
 
==== H2c. Prestressed Girders and Beams====
  
'''H2c1. Notes for all Girders and Beams '''
+
'''H2c1. Notes for all Girders and Beams. Place in general notes unless otherwise specified. '''  
 
 
'''Place general notes H2c1.1 thru H2c1.15 where space allows. '''
 
  
 
'''(H2c1.1)'''
 
'''(H2c1.1)'''
 
:Concrete for prestressed <u>girders</u> <u>beams</u> shall be Class A-1 with f'<sub>c</sub> = <u>&nbsp;&nbsp;&nbsp;&nbsp;</u> psi and f'<sub>ci</sub> = <u>&nbsp;&nbsp;&nbsp;&nbsp;</u> psi.
 
:Concrete for prestressed <u>girders</u> <u>beams</u> shall be Class A-1 with f'<sub>c</sub> = <u>&nbsp;&nbsp;&nbsp;&nbsp;</u> psi and f'<sub>ci</sub> = <u>&nbsp;&nbsp;&nbsp;&nbsp;</u> psi.
 
'''(H2c1.2)'''
 
:(+) indicates prestressing strand.
 
  
 
'''(H2c1.3)'''
 
'''(H2c1.3)'''
:Use <u>&nbsp;&nbsp;&nbsp;</u> strands with an initial prestress force of <u>&nbsp;&nbsp;&nbsp;</u> kips.
+
:Use ___, <u>1/2</u> <u>0.6</u>"ø, Grade 270, strands with an initial prestress force of <u>&nbsp;&nbsp;&nbsp;</u> kips.
  
 
'''(H2c1.4) '''
 
'''(H2c1.4) '''
:Prestressing tendons shall be uncoated, seven-wire, low-relaxation strands, <u>1/2</u>  <u>0.6</u> inch diameter in accordance with AASHTO M 203, Grade 270.  Pretensioned members shall be in accordance with Sec 1029.
+
:Pretensioned members shall be in accordance with Sec 1029.
  
 
'''(H2c1.5) '''
 
'''(H2c1.5) '''
 
:Fabricator shall be responsible for location and design of lifting devices.  
 
:Fabricator shall be responsible for location and design of lifting devices.  
  
'''(H2c1.6) Use when the camber diagram is placed on another sheet. '''
+
'''(H2c1.7) All girders and beams except double-tee girders. Use top flange blockout for NU girders only.'''
:For <u>Girder</u> <u>Beam</u> Camber Diagram, see Sheet No. __.
+
:Exterior and interior <u>girders</u> <u>beams</u> are the same, except for coil ties <u>,</u> <u>and</u> <u>top flange blockout</u> <u>,</u> <u>and</u> <u>coil inserts for</u> <u>slab drains</u> <u>and</u> <u>holes for steel intermediate diaphragms</u> <u>and holes for #6 bar</u>.
 +
 +
'''(H2c1.9) Use when the camber diagram is placed on another sheet. '''
 +
:For <u>Girder</u> <u>Beam</u> Camber Diagram, see Sheet No. __.  
  
'''Use notes H2c1.10 and H2c1.11 when steel intermediate diaphragms are present. '''
+
<div id="(H2c1.10)"></div>
 
+
'''(H2c1.10) Use when steel intermediate diaphragms are present.'''
'''(H2c1.10) '''
+
:The 1 1/2"ø holes shall be cast in the web for steel intermediate diaphragms. Drilling is not allowed. For location of holes and details of steel intermediate diaphragms, see Sheet No. __.
:The 1 1/2"ø holes shall be cast in the web for steel intermediate diaphragms. <u>Drilling is not allowed.</u>
 
 
 
'''(H2c1.11) '''
 
:For details of diaphragms, see Sheet No. __.  
 
  
 
'''(H2c1.15) Use when slab drains are present.  Use <u>drain blockouts</u> for double-tee girders, otherwise use <u>coil inserts at slab drains</u>. '''
 
'''(H2c1.15) Use when slab drains are present.  Use <u>drain blockouts</u> for double-tee girders, otherwise use <u>coil inserts at slab drains</u>. '''
:For location of <u>coil inserts at slab drains drain blockouts</u>, see Sheet No. __.
+
:For location of <u>coil inserts at slab drains</u> <u>drain blockouts</u>, see Sheet No. __.  
 
 
'''(H2c1.20) Place under the elevation of the girder or beam when applicable.  Use for all girders and beams except double-tee girders. Use second sentence with NU girders only. Use third sentence with box beam structures only.'''
 
:Exterior and interior <u>girders</u> <u>beams</u> are the same, except for coil ties <u>,</u> <u>and</u> <u>coil inserts for slab drains</u> <u>and</u> <u>holes for steel intermediate diaphragms</u> <u>and holes for #6 bar</u>. <u>Reinforcement support strands not shown for clarity. See Sheet No. __ for spacing of U1 and U2 bars.</u>
 
  
 
'''(H2c1.25) Place near vent hole details for stream crossings only for girder structures. Use <u>(one end only)</u> for flat grades otherwise use <u>upgrade</u>. '''
 
'''(H2c1.25) Place near vent hole details for stream crossings only for girder structures. Use <u>(one end only)</u> for flat grades otherwise use <u>upgrade</u>. '''
 
:Place vent holes at or near <u>upgrade</u> 1/3 point of girders <u>(one end only)</u> and clear reinforcing steel and strands by 1 1/2" minimum <u>and steel intermediate diaphragms bolt connection by 6" minimum</u>.   
 
:Place vent holes at or near <u>upgrade</u> 1/3 point of girders <u>(one end only)</u> and clear reinforcing steel and strands by 1 1/2" minimum <u>and steel intermediate diaphragms bolt connection by 6" minimum</u>.   
  
'''Place notes H2c1.30 and H2c1.31 near the bearing plate details.  '''
+
<div id="(H2c1.38)"></div>
 
+
'''(H2c1.38) Use <u>and #6 bars</u> for Bulb-Tee girders and NU-girders. '''
'''(H2c1.30) '''
+
:For location of coil ties <u>and #6 bars</u> at concrete bent diaphragms, see Sheet<u>s</u> No. __<u>and</u> __.   
:Galvanize the 1/2" bearing plate (ASTM A709 Grade 36) in accordance with ASTM A123.
 
 
 
'''(H2c1.31) '''
 
:Cost of furnishing, galvanizing and installing the 1/2" bearing plate (ASTM A709 Grade 36) and welded studs in the prestressed <u>girder</u> <u>beam</u> will be considered completely covered by the contract unit price for Prestressed Concrete <u>I-Girder</u> <u>Bulb-Tee Girder</u> <u>NU-Girder</u> <u>Spread Box Beam</u> <u>Adjacent Box Beam</u> <u>Spread Voided Slab Beam</u> <u>Adjacent Voided Slab Beam</u> <u>Solid Slab Beam</u>.
 
 
 
'''Place notes H2c1.35 thru H2c1.39 near the coil tie details.  Double-Tee girders and adjacent beams do not use coil ties.  '''
 
 
 
'''(H2c1.35) Use with end spans when both interior and exterior girders or beams are detailed on the same sheet and the 2’-6”long tie rod will not fit in the exterior diaphragm portion. Place *** at the end of the note specifying the centerlines of the coil tie rods.  '''
 
 
 
: '''***''' Length of coil tie rods at exterior <u>girders</u> <u>beams</u> at end bents = '- "
 
 
 
'''(H2c1.36) '''
 
:Cost of 3/4"ø coil tie rods placed in diaphragms will be considered completely covered by the contract unit price for Prestressed Concrete <u>I-Girder</u> <u>Bulb-Tee Girder</u> <u>NU-Girder</u> <u>Spread Box Beam</u> <u>Spread Voided Slab Beam</u>. 
 
 
 
'''(H2c1.37) '''
 
:Coil ties shall be held in place in the forms by slotted wire-setting-studs projecting thru forms. Studs are to be left in place or replaced with temporary plugs until <u>girders</u> <u>beams</u> are erected, then replaced by coil tie rods.
 
 
 
'''(H2c1.38) Use <u>and #6 bars</u> for Bulb-Tee girders and NU-girders. '''
 
:For location of coil ties <u>and #6 bars</u>, see Sheet<u>s</u> No. __<u>and</u> __.   
 
  
'''(H2c1.39) Use for Bulb-Tee girders and NU-girders. '''
+
'''(H2c1.39) Place note near coil tie detail for Bulb-Tee girders and NU-girders '''
 
:Cast 1”Ø hole horizontally in girder for #6 bar 5’-6" long and clear reinforcing steel or strands by 1 1/2" minimum.  
 
:Cast 1”Ø hole horizontally in girder for #6 bar 5’-6" long and clear reinforcing steel or strands by 1 1/2" minimum.  
 
   
 
   
'''(H2c1.40) For girders only, place near Dimensions detail when the panel option is used except for NU-Girders.  Place * at the top corners of the girder in the girder Dimensions detail. Use <u>1 1/2" to 1 3/4"</u> for P/S I-Girders Type 2, 3 and 4 otherwise use <u>3" to 3 1/4"</u>. '''  
+
'''(H2c1.44) Place near strand arrangement detail when strands are debonded (primarily with beams).'''
: '''*'''  At contractor's option a <u>1 1/2" to 1 3/4"</u> <u>3" to 3 1/4"</u> smooth finish strip is permitted to facilitate placement of preformed fiber expansion joint material or expanded or extruded polystyrene bedding material for the prestressed panels.
+
:All strands are fully bonded unless otherwise noted.
 
 
'''Place notes H2c1.45 and H2c1.46 near the strand details at girder ends. '''
 
  
'''(H2c1.45) Use when the bottom strands are not all bent-up. Place ** at the end of the note specifying which strands are bent-up. '''
+
'''(H2c1.46) Place near strands at girder or beam ends detail with non-integral bents. Adjust the details accordingly. '''
: '''**''' At the contractor's option the location for bent-up strands may be varied from that shown for fully bonded strands only. The total number of bent-up strands shall not be changed. One strand tie bar is required for each layer of bent-up strands except at end bents which require one bar on the bottom layer of strands only. No additional payment will be made if additional strand tie bars are required.  
+
:Prestressing strands at End Bents No. __ and __ <u>and Intermediate</u> <u>Bents</u> No.    and    shall be trimmed to within 1/8 inch of concrete if exposed, or 1 inch of concrete if encased. Exposed ends of girders shall be given 2 coats of an asphalt paint. Ends of girders which will be encased in concrete diaphragms shall not be painted.  
  
'''(H2c1.46) Use with non-integral bents only.  Adjust the details accordingly. '''
 
:Prestressing strands at End Bents No. __ and __ <u>and Intermediate</u> <u>Bents</u> No.    and    shall be trimmed to within 1/8 inch of concrete if exposed, or 1 inch of concrete if encased. Exposed ends of girders shall be given 2 coats of an asphalt paint. Ends of girders which will be encased in concrete diaphragms shall not be painted. 
 
  
 
+
'''H2c2. Additional NU-Girder Notes. Place with H2c1 general notes.'''  
'''H2c2. Additional NU-Girder Notes'''
 
 
 
'''Place general notes H2c2.2 and H2c2.3 with H2c1 general notes where space allows. '''
 
  
 
<div id="(H2c2.2)"></div>
 
<div id="(H2c2.2)"></div>
 
'''(H2c2.2) Use for NU 35 and NU 43 only '''
 
'''(H2c2.2) Use for NU 35 and NU 43 only '''
:The contractor shall provide bracing necessary for lateral and torsional stability of the girders during construction of the concrete slab and remove the bracing after the slab has attained 75% design strength. The cost for furnishing, installing, and removing bracing will be considered completely covered by the contract unit price for Prestressed Concrete NU-Girder.
+
:The contractor shall provide bracing necessary for lateral and torsional stability of the girders during construction of the concrete slab and remove the bracing after the slab has attained 75% design strength. Contractor shall not drill holes in the girders.  
  
 
'''(H2c2.3) '''
 
'''(H2c2.3) '''
Line 2,085: Line 2,341:
  
 
<div id="(H2c2.10)"></div>
 
<div id="(H2c2.10)"></div>
'''(H2c2.10) Place near girder dimension detail when the panel option is used.  Place * at the top corners of the girder in the girder dimensions detail. '''
 
: '''*''' Girder top flange shall be steel troweled to a smooth finish for 8" at the edges, as shown. Apply two layers of 30-lb. roofing felt as a bond breaker to this region only excluding where joint filler is applied. The center portion shall be rough finished by scarifying the surface transversely with a wire brush, and no laitance shall remain on the surface. 
 
  
 
+
'''H2c3. Additional Double-Tee Girder Notes. Place with H2c1 general notes. '''
'''H2c3. Additional Double-Tee Girder Notes '''
 
 
 
'''Place general notes H2c3.1 thru H2c3.6 with H2c1 general notes where space allows. '''
 
  
 
'''(H2c3.1) '''
 
'''(H2c3.1) '''
Line 2,121: Line 2,372:
 
<div id="H2c4. Additional Prestressed Concrete Box Beam Notes"></div>
 
<div id="H2c4. Additional Prestressed Concrete Box Beam Notes"></div>
  
'''H2c4. Additional Prestressed Concrete Box Beam Notes'''
+
'''H2c4. Blank'''
 
 
'''(H2c4.1) Place near strand arrangement detail when the panel option is used. Place * at the top corners of the beam in the strand arrangement detail. '''
 
: * Beam top flange shall be steel troweled to a smooth finish for 9” at the edges, as shown. Apply two layers of 30-lb. roofing felt as a bond breaker to this region only excluding where joint filler is applied. The center portion shall be rough finished by scarifying the surface transversely with a wire brush, and no laitance shall remain on the surface.
 
 
 
'''(H2c4.3) '''
 
:3/4”ø drain holes shall be provided at each end of each void, and shall be kept open at all times.
 
 
 
'''(H2c4.4) '''
 
:Beams shall be kept upright at all times. Support shall be within 12 inches of the ends only.
 
 
 
'''(H2c4.5) '''
 
:Void filler shall be non-absorptive cellular polystyrene, according to ASTM C 578, designed to withstand the forces imposed upon them during fabrication without substantial deformation such as bulging, sagging, or collapsing. Cardboard void filler will not be allowed. The outside dimensions of void filler shall be as shown on the plans. When two or more sections of void filler are used to make up a required length, they shall be effectively taped or spliced together.
 
 
'''(H2c4.6) '''
 
:Beams shall be finished similarly in accordance with Sec 1029, except as noted.
 
  
  
Line 2,145: Line 2,381:
 
<div id="(H2c6.1)"></div>
 
<div id="(H2c6.1)"></div>
  
'''(H2c6.1) Place with camber diagram for all girders and beams. '''
+
'''(H2c6.1) Place with camber diagram '''<font color="purple">[MS Cell]</font color="purple">''' for all girders and beams. '''
:Conversion factors for <u>girder</u> <u>beam</u> camber   
+
:Conversion factors for <u>girder</u> <u>beam</u> camber (Estimated at 90 days):  
  
 
:'''Use with spans 75' and greater in length. '''
 
:'''Use with spans 75' and greater in length. '''
Line 2,156: Line 2,392:
 
:'''Use with spans less than 75' in length. '''
 
:'''Use with spans less than 75' in length. '''
 
:0.25 pt. = 0.7125 x 0.5 pt.  
 
:0.25 pt. = 0.7125 x 0.5 pt.  
 +
<div id="Place notes H2c6.10 thru H2c6.14"></div>
 +
'''Place notes H2c6.10 thru H2c6.14 with slab haunching diagram '''<font color="purple">[MS Cell]</font color="purple">''' (slab thickness diagram '''<font color="purple">[MS Cell]</font color="purple">''' for double-tee girders and adjacent beams).  '''
  
'''Place notes H2c6.10 thru H2c6.14 with slab haunching diagram (slab thickness diagram for double-tee girders and adjacent beams).  '''
+
'''(H2c6.10) Omit underlined haunch segments for double-tee girders and adjacent beams.  The minimum embedment sentence is not applicable for Box Beams. Omit hairpin bar when not used on the plan details.'''
 +
:If <u>girder</u> <u>beam</u> camber is different from that shown in the camber diagram, in order to maintain minimum slab thickness, <u>an adjustment of the slab haunches,</u> an increase in slab thickness or a raise in grade uniformly throughout the structure shall be necessary. <u>The haunch shall be limited to ensure the projecting girder reinforcement</u> <u>or hairpin bar</u> <u>is embedded into slab at least 2 inches.</u> No payment will be made for additional labor or materials required for variation in <u>haunching,</u> slab thickness or grade adjustment. 
  
'''(H2c6.10) Use for all girders and beams. Omit underline parts for double-tee girders and adjacent beams.  '''
+
'''(H2c6.11) Omit “haunches” for double-tee girders and adjacent beams.  '''
:If <u>girder</u> <u>beam</u> camber is different from that shown in the camber diagram, in order to maintain minimum slab thickness <u>adjustment of the slab haunches</u>, an increase in slab thickness or a raise in grade uniformly throughout the structure shall be necessary. No payment will be made for additional labor or materials required for variation in <u>haunching,</u> slab thickness or grade adjustment. 
+
:Concrete in the slab <u>haunches</u> is included in the Estimated Quantities for Slab on Concrete <u>I-Girder</u> <u>Bulb-Tee Girder</u> <u>NU-Girder</u> <u>Beam</u> <u>Adjacent Beam</u>.   
 
 
'''(H2c6.11) Use for all girders and beams except for double-tee girders and adjacent beams.  '''
 
:Concrete in the slab haunches is included in the Estimated Quantities for Slab on Concrete <u>I-Girder</u> <u>Bulb-Tee Girder</u> <u>NU-Girder</u> <u>Beam</u>.   
 
 
 
'''(H2c6.12) Use only for double-tee girders and adjacent beams. '''
 
:Concrete in the slab overlay is included in the estimated quantities for Reinforced Concrete Slab Overlay.
 
  
 
'''(H2c6.13) Use only for double-tee girders and adjacent beams.  Underline part only required when the slab thickness within parabolic crown is less than the minimum slab thickness.  A = minimum slab thickness.  B = slab thickness at crown centerline.  '''
 
'''(H2c6.13) Use only for double-tee girders and adjacent beams.  Underline part only required when the slab thickness within parabolic crown is less than the minimum slab thickness.  A = minimum slab thickness.  B = slab thickness at crown centerline.  '''
Line 2,181: Line 2,414:
  
 
'''(H2c7.2) For the location of (**), see [http://epg.modot.org/index.php?title=751.22_P/S_Concrete_I_Girders#751.22.3.13_Intermediate_Diaphragms EPG 751.22.3.13 Intermediate Diaphragms].  '''
 
'''(H2c7.2) For the location of (**), see [http://epg.modot.org/index.php?title=751.22_P/S_Concrete_I_Girders#751.22.3.13_Intermediate_Diaphragms EPG 751.22.3.13 Intermediate Diaphragms].  '''
:(**) Bolts shall be tightened to provide a tension of one-half that specified in Sec 712 for high strength bolt installation. A325 bolts may be substituted for and installed in accordance with the requirements for the specified A307 bolts.  
+
:(**) Bolts shall be tightened to provide a tension of one-half that specified in Sec 712 for high strength bolt installation. ASTM F3125 Grade A325 Type 1 bolts may be substituted for and installed in accordance with the requirements for the specified A307 bolts.
  
 
'''(H2c7.3) '''
 
'''(H2c7.3) '''
Line 2,212: Line 2,445:
  
 
'''(H3.2)'''
 
'''(H3.2)'''
:Anchor bolts shall be coated with a minimum of two coats of inorganic zinc primer (5 mils minimum).
+
:Anchor bolts shall be coated with a minimum of two coats of inorganic zinc primer to provide a total dry film thickness of 4 mils minimum, 6 mils maximum, or galvanized in accordance with [https://www.modot.org/missouri-standard-specifications-highway-construction Sec 1081].
  
 
'''(H3.3)'''
 
'''(H3.3)'''
Line 2,218: Line 2,451:
  
 
'''(H3.4) <font color="purple">[MS Cell]</font color="purple">'''
 
'''(H3.4) <font color="purple">[MS Cell]</font color="purple">'''
:"[[Image:751.50 finish mark.gif]]" Indicates machine finish surface.
+
:[[Image:751.50 finish mark.gif]] Indicates machine finish surface.
  
 
'''(H3.5)'''
 
'''(H3.5)'''
Line 2,227: Line 2,460:
  
 
'''(H3.6)'''
 
'''(H3.6)'''
:Anchor bolts for Type D bearings shall be <u>1 1/4"&oslash;</u> <u>1 1/2"&oslash;</u> ASTM F1554 Grade 55 swedged bolts and shall extend <u>12"</u> <u>15"</u> into the concrete with ASTM A563 Grade A Hex or Heavy Hex nuts.  Actual manufacturer's certified mill test reports (chemical and mechanical) shall be provided.  Use ASTM F436 hardened washers for the fixed bearings and no heavy hexagon nuts or hardened washers for the expansion bearings.  Swedging shall be 1" less than extension into the concrete.
+
:Anchor bolts for Type D bearings shall be <u>1 1/4"&oslash;</u> <u>1 1/2"&oslash;</u> ASTM F1554 Grade 55 swedged bolts and shall extend <u>12"</u> <u>15"</u> into the concrete with ASTM A563 Grade A Heavy Hex nuts.  Actual manufacturer's certified mill test reports (chemical and mechanical) shall be provided.  Use ASTM F436 hardened washers for the fixed bearings and no heavy hex nuts or hardened washers for the expansion bearings.  Swedging shall be 1" less than extension into the concrete.
  
 
'''(H3.7)'''
 
'''(H3.7)'''
:Anchor bolts, hardened washers and heavy hexagon nuts shall be coated with a minimum of two coats of inorganic zinc primer (5 mils minimum).  
+
:Anchor bolts, hardened washers and heavy hex nuts shall be coated with a minimum of two coats of inorganic zinc primer to provide a total dry film thickness of 4 mils minimum, 6 mils maximum, or galvanized in accordance with [https://www.modot.org/missouri-standard-specifications-highway-construction Sec 1081].  
  
 
'''(H3.8)'''
 
'''(H3.8)'''
:Weight of the anchor bolts, hardened washers and heavy hexagon nuts for bearings are included in the weight of the Fabricated Structural Steel.
+
:Weight of the anchor bolts, hardened washers and heavy hex nuts for bearings are included in the weight of the Fabricated Structural Steel.
  
 
'''(H3.9) <font color="purple">[MS Cell]</font color="purple">'''
 
'''(H3.9) <font color="purple">[MS Cell]</font color="purple">'''
:"[[Image:751.50 finish mark.gif]]" Indicates machine finish surface.
+
:[[Image:751.50 finish mark.gif]] Indicates machine finish surface.
  
 
'''(H3.10)'''
 
'''(H3.10)'''
Line 2,252: Line 2,485:
  
 
'''(H3.15)'''
 
'''(H3.15)'''
:Anchor bolts for Type E bearings shall be <u>1 1/4"&oslash;</u> <u>1 1/2"&oslash;</u> ASTM F1554 Grade 55 swedged bolts and shall extend <u>12"</u> <u>15"</u> into the concrete with ASTM A563 Grade A Hex or Heavy Hex nuts.  Actual manufacturer's certified mill test reports (chemical and mechanical) shall be provided.  Use ASTM F436 hardened washers for the fixed bearings and no heavy hexagon nuts or hardened washers for the expansion bearings.  Swedging shall be 1" less than extension into the concrete.
+
:Anchor bolts for Type E bearings shall be <u>1 1/4"&oslash;</u> <u>1 1/2"&oslash;</u> ASTM F1554 Grade 55 swedged bolts and shall extend <u>12"</u> <u>15"</u> into the concrete with ASTM A563 Grade A Heavy Hex nuts.  Actual manufacturer's certified mill test reports (chemical and mechanical) shall be provided.  Use ASTM F436 hardened washers for the fixed bearings and no heavy hex nuts or hardened washers for the expansion bearings.  Swedging shall be 1" less than extension into the concrete.
  
 
'''(H3.16''')
 
'''(H3.16''')
:Anchor bolts, hardened washers and heavy hexagon nuts shall be coated with a minimum of two coats of inorganic zinc primer (5 mils minimum).  
+
:Anchor bolts, hardened washers and heavy hex nuts shall be coated with a minimum of two coats of inorganic zinc primer to provide a total dry film thickness of 4 mils minimum, 6 mils maximum, or galvanized in accordance with [https://www.modot.org/missouri-standard-specifications-highway-construction Sec 1081].
  
 
'''(H3.17)'''
 
'''(H3.17)'''
:Weight of the anchor bolts, hardened washers and heavy hexagon nuts for bearings are included in the weight of the Fabricated Structural Steel.
+
:Weight of the anchor bolts, hardened washers and heavy hex nuts for bearings are included in the weight of the Fabricated Structural Steel.
  
 
'''(H3.18) <font color="purple">[MS Cell]</font color="purple">'''
 
'''(H3.18) <font color="purple">[MS Cell]</font color="purple">'''
:"[[Image:751.50 finish mark.gif]]" Indicates machine finish surface.
+
:[[Image:751.50 finish mark.gif]] Indicates machine finish surface.
 
 
'''(H3.19) <font color="purple">[MS Cell]</font color="purple">'''
 
:[[Image:751.50 circled 1.gif]] bonded lubricant
 
  
 
'''(H3.20)'''
 
'''(H3.20)'''
Line 2,284: Line 2,514:
  
 
'''(H3.25)'''
 
'''(H3.25)'''
:Anchor bolts shall be <u>1 1/2"&oslash;</u> <u>2"&oslash;</u> <u>2 1/2"&oslash;</u> ASTM F1554 Grade 55 swedged bolts and shall extend <u>15"</u> <u>18"</u> <u>25"</u> into the concrete with ASTM A563 Grade A Hex or Heavy Hex nuts.  Actual manufacturer's certified mill test reports (chemical and mechanical) shall be provided.  Swedging shall be 1" less than extension into the concrete.
+
:Anchor bolts shall be <u>1 1/2"&oslash;</u> <u>2"&oslash;</u> <u>2 1/2"&oslash;</u> ASTM F1554 Grade 55 swedged bolts and shall extend <u>15"</u> <u>18"</u> <u>25"</u> into the concrete with ASTM A563 Grade A Heavy Hex nuts.  Actual manufacturer's certified mill test reports (chemical and mechanical) shall be provided.  Swedging shall be 1" less than extension into the concrete.
  
'''(H3.26)'''
+
'''(H3.26) Remove underline portion when superstructure is galvanized.'''
:All structural steel for the anchor bolts and heavy hexagon nuts shall be coated with a minimum of two coats of inorganic zinc primer (5 mils minimum).
+
:Anchor bolts and heavy hex nuts shall be <u>coated with a minimum of two coats of inorganic zinc primer to provide a total dry film thickness of 4 mils minimum, 6 mils maximum, or</u> galvanized in accordance with [https://www.modot.org/missouri-standard-specifications-highway-construction Sec 1081].
  
 
'''(H3.27)'''
 
'''(H3.27)'''
Line 2,296: Line 2,526:
  
  
'''Use the following note when ASTM A709 Grade 50W steel is not used for superstructure.'''
+
'''Use the following note when ASTM A709 Grade 50W steel is not used for superstructure and when steel superstructure is not galvanized.'''
  
 
'''(H3.29)  Use grade per Design Comps.'''
 
'''(H3.29)  Use grade per Design Comps.'''
:Structural steel for sole plate shall be ASTM A709 Grade <u>36</u> <u>50</u> and shall be coated with a minimum of two coats of inorganic zinc primer (5 mils minimum). The stainless steel plate shall be protected from any coating.
+
:Structural steel for sole plate shall be ASTM A709 Grade <u>36</u> <u>50</u> and shall be coated with a minimum of two coats of inorganic zinc primer to provide a total dry film thickness of 4 mils minimum, 6 mils maximum. The stainless steel plate shall be protected from any coating.
  
 +
<div id="Use the following note when ASTM A709 Grade 50W steel"></div>
 +
'''Use the following note when ASTM A709 Grade 50W steel is used for superstructure. Use the underlined portion at/near expansion joints where bearings are within the coating limits as required in [https://www.modot.org/missouri-standard-specifications-highway-construction Sec 1081.10.3.4].'''
 +
<div id="(H3.29.1)"></div>
 +
'''(H3.29.1)'''
 +
:Structural steel for sole plate shall be ASTM A709 Grade 50W <u>and shall be coated with a minimum of two coats of inorganic zinc primer to provide a total dry film thickness of 4 mils minimum, 6 mils maximum. The stainless steel plate shall be protected from any coating</u>.  The welds shall have corrosion resistance and weathering characteristics compatible with the base material.
 +
<div id="(H3.29.2)"></div>
 +
'''Use the following note when steel superstructure is galvanized. '''
  
'''Use the following note when ASTM A709 Grade 50W steel is used for superstructure.'''
+
'''(H3.29.2)'''
 
+
:Structural steel for sole plate shall be ASTM A709 Grade <u>36</u> <u>50</u> and shall be galvanized in accordance with [https://www.modot.org/missouri-standard-specifications-highway-construction Sec 1081]. The stainless steel plate shall be protected from galvanizing.  Galvanizing material shall be omitted or removed one inch clear of field weld locations. The method used to omit or remove the galvanizing material shall be masking, grinding or other methods as approved by the engineer. Field galvanize the field weld area in accordance with [https://www.modot.org/missouri-standard-specifications-highway-construction Sec 1081] by zinc alloy stick method.
'''(H3.29.1)'''
 
:Structural steel for sole plate shall be ASTM A709 Grade 50W. The welds shall have corrosion resistance and weathering characteristics compatible with the base material. All structural steel for the anchor bolts and heavy hexagon nuts shall be coated with a minimum of two coats of inorganic zinc primer (5 mils minimum).
 
  
 
'''(H3.30)'''
 
'''(H3.30)'''
Line 2,322: Line 2,557:
  
 
'''(H3.45)'''
 
'''(H3.45)'''
:Anchor bolts shall be <u>1 1/2"&oslash;</u> <u>2"&oslash;</u> <u>2 1/2"&oslash;</u> ASTM F1554 Grade 55 swedged bolts and shall extend <u>15"</u> <u>18"</u> <u>25"</u> into the concrete with ASTM A563 Grade A Hex or Heavy Hex nuts.  Actual manufacturer's certified mill test reports (chemical and mechanical) shall be provided.  Swedging shall be 1" less than extension into the concrete.
+
:Anchor bolts shall be <u>1 1/2"&oslash;</u> <u>2"&oslash;</u> <u>2 1/2"&oslash;</u> ASTM F1554 Grade 55 swedged bolts and shall extend <u>15"</u> <u>18"</u> <u>25"</u> into the concrete with ASTM A563 Grade A Heavy Hex nuts.  Actual manufacturer's certified mill test reports (chemical and mechanical) shall be provided.  Swedging shall be 1" less than extension into the concrete.
  
'''(H3.46)'''
+
'''(H3.46) Remove underline portion when superstructure is galvanized.'''
:All structural steel for the anchor bolts and heavy hexagon nuts shall be coated with a minimum of two coats of inorganic zinc primer (5 mils minimum).
+
:Anchor bolts and heavy hex nuts shall be <u>coated with a minimum of two coats of inorganic zinc primer to provide a total dry film thickness of 4 mils minimum, 6 mils maximum, or</u> galvanized in accordance with [https://www.modot.org/missouri-standard-specifications-highway-construction Sec 1081].
  
 
'''(H3.47)'''
 
'''(H3.47)'''
Line 2,333: Line 2,568:
 
:Anchor bolts shall be at the centerline of slotted hole at 60&deg;F. Bearing position shall be adjusted '''R''' for each 10&deg; fall or rise in temperature at installation.
 
:Anchor bolts shall be at the centerline of slotted hole at 60&deg;F. Bearing position shall be adjusted '''R''' for each 10&deg; fall or rise in temperature at installation.
  
'''(H3.49)  Use grade per Design Comps. Use when ASTM A709 Grade 50W steel is not used for superstructure.'''
+
'''(H3.49)  Use grade per Design Comps. Use when ASTM A709 Grade 50W steel is not used for superstructure and when steel superstructure is not galvanized. '''
:Structural steel for sole plate shall be ASTM A709 Grade <u>36</u> <u>50</u> and shall be coated with a minimum of two coats of inorganic zinc primer (5 mils minimum).
+
:Structural steel for sole plate shall be ASTM A709 Grade <u>36</u> <u>50</u> and shall be coated with a minimum of two coats of inorganic zinc primer to provide a total dry film thickness of 4 mils minimum, 6 mils maximum.
 
+
<div id="(H3.49.1) Use when ASTM A709 Grade 50W steel"></div>
'''(H3.49.1) Use when ASTM A709 Grade 50W steel is used for superstructure.'''
+
'''(H3.49.1) Use when ASTM A709 Grade 50W steel is used for superstructure. Use the underlined portion at/near expansion joints where bearings are within the coating limits as required in [https://www.modot.org/missouri-standard-specifications-highway-construction Sec 1081.10.3.4].'''
:Structural steel for sole plate shall be ASTM A709 Grade 50W.  The welds shall have corrosion resistance and weathering characteristics compatible with the base material. All structural steel for the anchor bolts and heavy hexagon nuts shall be coated with a minimum of two coats of inorganic zinc primer (5 mils minimum).
+
:Structural steel for sole plate shall be ASTM A709 Grade 50W <u>and shall be coated with a minimum of two coats of inorganic zinc primer to provide a total dry film thickness of 4 mils minimum, 6 mils maximum</u>.  The welds shall have corrosion resistance and weathering characteristics compatible with the base material.
 +
<div id="(H3.49.2)"></div>
 +
'''(H3.49.2) Use the following note when steel superstructure is galvanized.'''
 +
:Structural steel for sole plate shall be ASTM A709 Grade <u>36</u> <u>50</u> and shall be galvanized in accordance with [https://www.modot.org/missouri-standard-specifications-highway-construction Sec 1081]. Galvanizing material shall be omitted or removed one inch clear of field weld locations. The method used to omit or remove the galvanizing material shall be masking, grinding or other methods as approved by the engineer. Field galvanize the field weld area in accordance with [https://www.modot.org/missouri-standard-specifications-highway-construction Sec 1081] by zinc alloy stick method.
  
 
'''(H3.50)'''
 
'''(H3.50)'''
Line 2,377: Line 2,615:
  
 
'''(H3.76)'''
 
'''(H3.76)'''
:Anchor bolts shall be 1 1/2"&oslash; ASTM F1554 Grade 55 swedge bolts and shall extend 15" into concrete with ASTM A563 Grade A Hex or Heavy Hex nuts.  Actual manufacturer's certified mill test reports (chemical and mechanical) shall be provided.  Furnish one 4"&oslash; pin, AISI C1042, with 2 heavy hexagon pin nuts.
+
:Anchor bolts shall be 1 1/2"&oslash; ASTM F1554 Grade 55 swedge bolts and shall extend 15" into concrete with ASTM A563 Grade A Heavy Hex nuts.  Actual manufacturer's certified mill test reports (chemical and mechanical) shall be provided.  Furnish one 4"&oslash; pin, AISI C1042, with 2 heavy hexagon pin nuts.
  
 
'''(H3.77)'''
 
'''(H3.77)'''
Line 2,385: Line 2,623:
 
:Shop drawings are not required for the lead plates and the preformed fabric pads.
 
:Shop drawings are not required for the lead plates and the preformed fabric pads.
  
=== H4. Conduit System ===
+
====H3f. Pot Bearing Pad Assembly====
  
'''(H4.1)'''
+
'''(H3.79)'''
:Cost of furnishing and placing anchor bolts for light standard will be considered completely covered by the contract unit price for other items.
 
  
'''(H4.2) Use for all conduits, except if encased in concrete, 3 in. minimum cover is not possible in slab.'''
+
:The bearing design shall conform to the provisions of the latest edition of AASHTO LRFD Bridge Design Specifications.
:All conduits shall be rigid nonmetallic schedule 40 heavy wall polyvinyl chloride (PVC) <u>with 3" minimum cover in concrete</u>.  Each section of conduit shall bear the Underwriters Laboratories (UL) label.
+
 +
'''(H3.80)'''
  
'''Use Notes (H.4.2.1) and (H4.2.2) for all conduits when conduit clamps are required.'''
+
:The contractor, in coordination with the bearing manufacturer, shall be responsible for sizing the sole plate and masonry plate and determining the size, number, and location of anchor bolts based on the load and movement capacities, indicated in the Bearing Data.
 +
 +
'''(H3.81)'''
  
'''(H4.2.1)'''
+
:The contractor shall submit calculations sealed by a Professional Engineer, licensed in the state of Missouri, indicating conformance with design load and material criteria in the contract documents.
:All conduit clamps shall be commercially-available, nonmetallic conduit clamps and approved by the engineer.
+
 +
'''(H3.82)'''
  
'''(H4.2.2)'''  
+
:'''(1)''' Maximum vertical dimension of the complete bearing. If the actual bearing dimension differs, adjustments shall be made in the thickness of the sole plate, masonry plate and concrete pad as needed by the contractor at no additional cost to the owner. Contractor shall submit proposed method of adjustment to Engineer for approval.
:Anchor bolts and nuts shall be ASTM F1554 Grade 55. Anchor bolts, nuts and washers shall be fully galvanized.  
+
 +
'''(H3.83)'''
  
'''(H4.3)'''
+
:'''(2)''' Estimated horizontal dimension of the pot bearing device. If the actual dimension differs, adjust the size of the sole plate and masonry plate as needed by the contractor at no additional cost to the owner.
:Shift reinforcing steel in field where necessary to clear conduit and junction boxes.
+
 +
'''(H3.84)'''
  
'''(H4.4)'''
+
:'''(5)''' The temperature of the steel adjacent to the elastomeric should be kept below 250°F.
:Light standards, wiring and fixtures shall be furnished and installed by others.
+
 +
'''(H3.85)'''
  
'''(H4.5)'''
+
:The Dimension H in the Bearing Data Table represents the assumed total height of bearing mechanism between the sole plate and masonry plate used by the designer to establish the pedestal elevations.
:Top of light standard supports shall be made horizontal; anchor bolts shall be placed vertically.
+
 +
'''(H3.86)'''
  
'''(H4.6)'''
+
:The bearings shall be manufactured pot bearings, designed for the load and movement capacities indicated in the Bearing Data Table.
:For details of <u>light standards,</u> <u>underdeck lighting,</u> <u>and wiring</u>, see electrical plans.
+
 +
'''(H3.87)'''
  
'''(H4.7) Use for conduits to be encased in concrete at open, closed or filled joints. Use 150°F, 120°F for steel superstructure.  Use 120°F, 110°F for concrete superstructure.  Modify note to include giving the total expansion movement per expansion fitting if multiple fittings are used and movement is different, and delineate fittings on plans.'''
+
:All expansion Bearings shall have maximum friction coefficient of 3%.
:Expansion fittings shall be placed as shown and set in accordance with the manufacturer's requirements and based on the air temperature at the time of setting given an estimated total expansion movement of<u>&nbsp;&nbsp;&nbsp; inches at open joints</u> <u>and</u> <u>&nbsp;&nbsp;&nbsp; inches at filled joints</u> using a maximum temperature range of <u>150</u> <u>120</u>°F and a maximum temperature of <u>120</u> <u>110</u>°F.
+
 +
'''(H3.88)'''
  
'''(H4.7.1) Use for conduits not to be encased in concrete and for structures with open or closed joints in the superstructure.'''
+
:Steel for pot bearings shall be AASHTO M270 Grade 50 and shall be galvanized. Steel for sole plate and masonry plates shall be AASHTO M270 Grade 50.
:Expansion fittings shall be placed as shown and set in accordance with the manufacturer's requirements and based on the air temperature at the time of setting given an estimated total expansion movement of<u>&nbsp;&nbsp;&nbsp; inches at open joints</u> <u>and</u> <u>&nbsp;&nbsp;&nbsp; inches at closed joints</u> using a maximum temperature range of 110°F. Additional expansion fittings beyond what is specified on the bridge plans shall be provided and placed in accordance with the conduit manufacturer’s recommendations.
+
 +
'''(H3.89)'''
  
'''(H.4.7.2) Use for conduits not to be encased in concrete and for structures without open or closed joints in the superstructure.'''
+
:Anchor bolts shall conform to ASTM F1554 Grade 55. The anchor bolts shall be the swedge-type and shall have a minimum diameter of 1 1/2-inches and extend a minimum of __-inches into the concrete. Swedging shall be 1-inch less than the extension into the concrete.
:Additional expansion fittings beyond what is specified on the bridge plans shall be provided and placed in accordance with the conduit manufacturer’s recommendations.
+
 +
'''(H3.90)'''
  
'''(H4.7.3) Use for multiple conduits to be encased in concrete.'''  
+
:Anchor bolts shall be installed using a hardened steel washer at each exposed location.
:Minimum clearance preferred between conduits placed in the safety barrier curb shall be 1”.
+
 +
'''(H3.91)'''
  
'''(H4.8) Use "surface" mounting, except adjacent to sidewalks, where mounting box on existing concrete.  Use "flush" mounting where box is to be encased in concrete.'''
+
:Washers shall conform to ASTM F463.
:All end bent <u>and safety barrier curb</u> junction boxes shall be PVC molded in accordance with Sec 1062 and designed for <u>flush</u> <u>surface</u> mounting.  The conduit terminations shall be permanent or separable.  The terminations and covers shall be of watertight construction and shall meet requirements for NEMA 4 enclosure.
 
  
'''(H4.8.1) Use for all junction boxes to be encased in concrete at the roadway face of the safety barrier curb.'''
+
'''(H3.92)'''
:Placement of junction boxes and covers, complete in place, shall be flush with the roadway face of the safety barrier curb.  Junction boxes and covers may be recessed up to ¼”.
 
  
'''(H4.9) Use for all conduits not to be encased in concrete.'''
+
Anchor bolts and hardened washers shall be coated with a minimum of two coats of inorganic zinc primer to provide a total dry film thickness of 4 mils minimum, 6 mils maximum, or galvanized in accordance with [https://www.modot.org/missouri-standard-specifications-highway-construction Sec 1081].
:Weep holes shall be provided at low points or other critical locations to drain any moisture in the conduit system.  Conduit shall be sloped to drain.
+
 +
'''(H3.93)'''
  
'''(H4.9.1) Use for all conduits to be encased in concrete.'''  
+
:Certified mill test reports, conforming to the requirements of the specifications, for the metals of the pot bearing device, sole plate, masonry plate and anchor bolts shall be submitted.
:Drainage shall be provided at low points or other critical locations of all conduits and all junction boxes in accordance with Sec 707.  All conduits shall be sloped to drain where possible.
+
 +
'''(H3.94)'''
  
'''(H4.10) Use for conduit not encased in concrete.'''
+
:The masonry plate shall be prepared per the specifications and shop-coated with two coats of inorganic zinc primer to provide a total dry film thickness of 4 mils minimum, 6 mils maximum.
:All conduits shall be secured to concrete with nonmetallic clamps at about 5'-0" cts.  Concrete anchors for clamps shall be in accordance with Federal Specification FF-S-325, Group II, Type 4, Class I and shall be galvanized in accordance with ASTM A153, B695-91 Class 50 or stainless steelMinimum embedment in concrete shall be 1 3/4". The supplier shall furnish a manufacturer's certification that the concrete anchors meet the required material and galvanizing specifications.
+
   
 +
'''(H3.95)'''
  
'''(H4.11) Use for payment of Conduit System.'''
+
:The sole plate shall be prepared per the specifications and shop-coated with two coats of inorganic zinc primer to provide a total dry film thickness of 4 mils minimum, 6 mils maximum.
:Payment for furnishing and installing Conduit System, complete in place, will be considered completely covered by the contract lump sum price for Conduit System on Structure.
+
 +
'''(H3.96)'''
  
=== H5. Expansion Devices ===
+
:The bearing device, sole plate and masonry plate shall be assembled in the shop and the bearing assembly shall be field welded to the bottom flange of the steel cap beam. The welds shall be designed for the load capacities indicated in the Bearing Data Table.
 +
 +
'''(H3.97)'''
  
 +
:After installation of the bearings, any uncoated or damaged surfaces of the masonry and sole plates shall be prepared in accordance with the specifications and field-coated with inorganic zinc primer to provide a total dry film thickness of 4 mils minimum, 6 mils maximum.
  
==== H5a. Finger Plate ====
+
 +
'''(H3.98)'''
  
'''(H5.1) For stage construction or other special cases, see Structural Project Manager.'''
+
:After installation of the bearings and field-applied prime coats, the surfaces of the masonry and sole plates shall be field-coated with System G intermediate and finish coat.
:Finger plate shall be cut with a machine guided gas torch from one plate.  The plate from which fingers are cut may be spliced before fingers are cut.  The surface of cut shall be perpendicular to the surface of plate.  The cut shall not exceed 1/8" in width.  The centerline of cut shall not deviate more than 1/16" from the position of centerline of cut shown.  No splicing of finger plate or finger plate assembly will be allowed after fingers are cut.  The expansion device shall be fabricated and installed to the crown and grade of the roadway.
+
 +
'''(H3.99)'''
  
'''(H5.2)'''
+
:All bearings shall be marked prior to shipping.  The marks shall include the bearing location on the bridge and a direction arrow that points up-station.  All marks shall be permanent and be visible after the bearing is installed.
:Plan dimensions are based on installation at 60&deg;F.  The expansion gap and other dimensions shall be increased or decreased <u>&nbsp;&nbsp;&nbsp;</u>" for each 10&deg; fall or rise in temperature at installation.
+
 +
'''(H3.100)'''
  
'''(H5.3)'''
+
:The pot bearing device, sole plate, masonry plate, anchor bolts, washers, anchor bolts wells and any other appurtenances included in the fabrication and installation of the pot bearing device shall be incidental to the pay item Pot Bearings.
:Material for the expansion device shall be ASTM A709 Grade 36 structural steel.  Anchors for the expansion device shall be in accordance with Sec 1037.
+
 +
'''(H3.101)'''
  
'''(H5.4)'''
+
:Whenever jacking of the Superstructure is needed to reset the bearings, the contractor shall submit a jacking sequence for approval.
:Structural steel for the expansion device and curb plate shall be coated with a minimum of two coats of inorganic zinc primer (5 mils minimum) or galvanized in accordance with ASTM A123.  Anchors need not be protected from overspray.
 
  
'''(H5.5)'''
+
=== H4. Conduit System ===
:Payment for furnishing, coating or galvanizing and installing the structural steel for the expansion device will be considered completely covered by the contract unit price for Expansion Device (Finger Plate) per linear foot.
 
  
'''(H5.6)'''
+
'''(H4.1)'''
:Concrete shall be forced under and around finger plate supporting hardware, anchors, angles and bars. Proper consolidation shall be achieved by localized internal vibration.
+
:Cost of furnishing and placing anchor bolts for light standard will be considered completely covered by the contract unit price for other items.
  
'''(H5.7) Use note for steel structures.'''
+
'''(H4.2) Use for all conduits, except if encased in concrete, 3 in. minimum cover is not possible in slab.'''
:All holes shown for connections to be subpunched 11/16"&oslash; (shop or field drill) and reamed to 13/16"&oslash; in field.
+
:All conduits shall be rigid nonmetallic schedule 40 heavy wall polyvinyl chloride (PVC) <u>with 3" minimum cover in concrete</u>.  Each section of conduit shall bear the Underwriters Laboratories (UL) label.
  
'''(H5.8) Place note near "Plan of Slab".'''
+
'''Use Notes (H.4.2.1) and (H4.2.2) for all conduits when conduit clamps are required.'''
:'''"the web of W14 x 43" is for steel structures'''
 
:'''"the 3/4" vertical mounting plate" is for P/S structures.'''
 
:Longitudinal reinforcing steel shall be placed so that ends shall not be more than &plusmn;1" from <u>the web of W14 x 43</u> <u>and</u> <u>the 3/4" vertical mounting plate</u> at the expansion device.
 
  
'''(H5.9)'''
+
'''(H4.2.1)'''
:Complete joint penetration welds utilized in the fabrication of the expansion device shall be nondestructively tested by an approved method.
+
:All conduit clamps shall be commercially-available, nonmetallic conduit clamps and approved by the engineer.
  
'''(H5.10)'''  
+
'''(H4.2.2)'''  
:Curb plate anchors shall be a drilled cone expansion or a cast-in-place wing type threaded insert. The minimum ultimate pullout capacity for these anchors shall be 2700 lbs in f'c = 4000 psi concrete. Lead anchors will not be permitted. Holes in the barrier curb for anchors shall not be drilled until the concrete is at least 7 days old.
+
:Anchor bolts and nuts shall be ASTM F1554 Grade 55. Anchor bolts, nuts and washers shall be galvanized in accordance with AASHTO M 232 (ASTM A153), Class C, or ASTM B695, Class 55.
  
==== H5b. Flat Plate ====
+
'''(H4.3)'''
 +
:Shift reinforcing steel in field where necessary to clear conduit and junction boxes.
  
'''(H5.16)'''
+
'''(H4.4)'''
:Expansion device shall be fabricated in one section, except for stage construction and when the length is over 50 feet.  A complete joint penetration groove welded splice shall be required.  Welds shall be ground flush to provide a smooth surface.  The expansion device shall be fabricated and installed to the crown and grade of the roadway.
+
:Light standards, wiring and fixtures shall be furnished and installed by others.
  
'''(H5.17)'''
+
'''(H4.5)'''
:Plan dimensions are based on installation at 60&deg;F.  The expansion gap and other dimensions shall be increased or decreased <u>&nbsp;&nbsp;&nbsp;</u>" for each 10&deg; fall or rise in temperature at installation.
+
:Top of light standard supports shall be made horizontal; anchor bolts shall be placed vertically.
  
'''(H5.18)'''
+
'''(H4.6)'''
:Material for the expansion device shall be ASTM A709 Grade 36 structural steel.  Anchors for the expansion device shall be in accordance with Sec 1037.
+
:For details of <u>light standards,</u> <u>underdeck lighting,</u> <u>and wiring</u>, see electrical plans.
  
'''(H5.19)'''
+
'''(H4.7) Use for conduits to be encased in concrete at open, closed or filled joints. Use 150°F, 120°F for steel superstructure.  Use 120°F, 110°F for concrete superstructure.  Modify note to include giving the total expansion movement per expansion fitting if multiple fittings are used and movement is different, and delineate fittings on plans.'''
:Structural steel for the expansion device and curb plate shall be coated with a minimum of two coats of inorganic zinc primer (5 mils minimum) or galvanized in accordance with ASTM A123. Anchors need not be protected from overspray.
+
:Expansion fittings shall be placed as shown and set in accordance with the manufacturer's requirements and based on the air temperature at the time of setting given an estimated total expansion movement of<u>&nbsp;&nbsp;&nbsp; inches at open joints</u> <u>and</u> <u>&nbsp;&nbsp;&nbsp; inches at filled joints</u> using a maximum temperature range of <u>150</u> <u>120</u>°F and a maximum temperature of <u>120</u> <u>110</u>°F.
  
'''(H5.20)'''
+
'''(H4.7.1) Use for conduits not to be encased in concrete and for structures with open or closed joints in the superstructure.'''
:Payment for furnishing, coating or galvanizing and installing the structural steel for the expansion device will be considered completely covered by the contract unit price for Expansion Device (Flat Plate) per linear foot.
+
:Expansion fittings shall be placed as shown and set in accordance with the manufacturer's requirements and based on the air temperature at the time of setting given an estimated total expansion movement of<u>&nbsp;&nbsp;&nbsp; inches at open joints</u> <u>and</u> <u>&nbsp;&nbsp;&nbsp; inches at closed joints</u> using a maximum temperature range of 110°F. Additional expansion fittings beyond what is specified on the bridge plans shall be provided and placed in accordance with the conduit manufacturer’s recommendations.
  
'''(H5.21)'''
+
'''(H.4.7.2) Use for conduits not to be encased in concrete and for structures without open or closed joints in the superstructure.'''
:Concrete shall be forced under and around the flat plate, anchors and angles.  Proper consolidation shall be achieved by localized internal vibration.  Finishing of the concrete shall be achieved by hand finishing within one foot of the expansion device.  The vertical and horizontal concrete vent holes shall be offset from each other.  Do not alternate holes at the 12" spacing.
+
:Additional expansion fittings beyond what is specified on the bridge plans shall be provided and placed in accordance with the conduit manufacturer’s recommendations.
  
'''(H5.22) Use this note when expansion device is at an end bent.'''
+
'''(H4.7.3) Use for multiple conduits to be encased in concrete.'''  
:Bevel plates shall be used at end bents when the grade of the slab at the expansion device is 3% or more.
+
:Minimum clearance preferred between conduits placed in barrier shall be 1”.  
  
'''(H5.23) Place this note near "Plan of Slab".'''
+
'''(H4.8) Use "surface" mounting, except adjacent to sidewalks, where mounting box on existing concrete.  Use "flush" mounting where box is to be encased in concrete.'''
:Longitudinal reinforcing steel shall be placed so that ends shall not be more than &plusmn;1" from <u>vertical plate</u> <u>and</u> <u>the vertical leg of the angle</u> at the expansion device.
+
:All end bent <u>and barrier</u> junction boxes shall be PVC molded in accordance with Sec 1062 and designed for <u>flush</u> <u>surface</u> mounting.  The conduit terminations shall be permanent or separable.  The terminations and covers shall be of watertight construction and shall meet requirements for NEMA 4 enclosure.
  
'''(H5.24)'''
+
'''(H4.8.1) Use for all junction boxes to be encased in concrete at the roadway face of barrier.'''
:Complete joint penetration welds utilized in the fabrication of the expansion device shall be nondestructively tested by an approved method.
+
:Placement of junction boxes and covers, complete in place, shall be flush with the roadway face of barrier.  Junction boxes and covers may be recessed up to ¼”.
  
'''(H5.25)'''
+
'''(H4.9) Use for all conduits not to be encased in concrete.'''
:Curb plate anchors shall be a drilled cone expansion or a cast-in-place wing type threaded insertThe minimum ultimate pullout capacity for these anchors shall be 2700 lbs in f'c = 4000 psi concrete.  Lead anchors will not be permitted.  Holes in the barrier curb for anchors shall not be drilled until the concrete is at least 7 days old.
+
:Weep holes shall be provided at low points or other critical locations to drain any moisture in the conduit systemConduit shall be sloped to drain.
  
==== H5c. Preformed Compression Joint Seal ====
+
'''(H4.9.1) Use for all conduits to be encased in concrete.'''
 +
:Drainage shall be provided at low points or other critical locations of all conduits and all junction boxes in accordance with Sec 707.  All conduits shall be sloped to drain where possible.
  
'''(H5.31)'''
+
'''(H4.10) Use for conduit not encased in concrete.'''
:Expansion joint system shall be fabricated in one section, except for stage construction and when the length is over 50 feet.  A complete joint penetration groove welded splice shall be requiredWelds shall be ground flush to provide a smooth surface.  The expansion joint system shall be fabricated and installed to the crown and grade of the roadway.
+
:All conduits shall be secured to concrete with nonmetallic clamps at about 5'-0" cts.  Concrete anchors for clamps shall be in accordance with Federal Specification FF-S-325, Group II, Type 4, Class I and shall be galvanized in accordance with AASHTO M 232 (ASTM A153), Class C, ASTM B695 Class 55 or stainless steelMinimum embedment in concrete shall be 1 3/4".  The supplier shall furnish a manufacturer's certification that the concrete anchors meet the required material and galvanizing specifications.
  
'''(H5.32)'''
+
'''(H4.11) Use for junction box. '''
:Plan dimensions are based on installation at 60&deg;F. The expansion gap and other dimensions shall be increased or decreased <u>&nbsp;&nbsp;&nbsp;</u>" for each 10&deg; fall or rise in temperature at installation.
+
:Junction box size shown on plan may require special order. No other size may be substituted.
  
'''(H5.33)'''
+
'''(H4.12)   '''
:Structural steel for the expansion joint system shall be ASTM A709 Grade 36.  Anchors for the expansion joint system shall be in accordance with Sec 1037.  Preformed compression seal expansion joint system shall be in accordance with Sec 717.
+
:MoDOT Construction Personnel: Indicate in field and on bridge plans for future work the exact location of buried conduit at ends of bridge that are capped and not immediately used.
  
'''(H5.34)'''
+
'''(H4.13) Use for payment of Conduit System.'''
:Structural steel for the expansion joint system shall be coated with a minimum of two coats of inorganic zinc primer (5 mils minimum) or galvanized in accordance with ASTM A123.  Anchors need not be protected from overspray.
+
:Payment for furnishing and installing Conduit System, complete in place, will be considered completely covered by the contract lump sum price for Conduit System on Structure.
  
'''(H5.35)'''
+
=== H5. Expansion Joint Systems ===
:Concrete shall be forced under armor angle and around anchors. Proper consolidation of the concrete shall be achieved by localized internal vibration.
 
  
'''(H5.36) Place this note near "Plan of Slab".'''
 
:Longitudinal reinforcing steel shall be placed so that ends shall not be more than &plusmn;1" from vertical leg of angle at the expansion joint system.
 
  
 +
==== H5a. Finger Plate ====
  
'''Place the following notes near the "Tables of Transverse Bridge Seal Dimensions".'''
+
'''(H5.1)  For stage construction or other special cases, see Structural Project Manager.'''
 +
:Finger plate shall be cut with a machine guided gas torch from one plate.  The plate from which fingers are cut may be spliced before fingers are cut.  The surface of cut shall be perpendicular to the surface of plate.  The cut shall not exceed 1/8" in width.  The centerline of cut shall not deviate more than 1/16" from the position of centerline of cut shown.  No splicing of finger plate or finger plate assembly will be allowed after fingers are cut.  The expansion device shall be fabricated and installed to the crown and grade of the roadway.
  
'''(H5.38) <font color="purple">[MS Cell]</font color="purple">'''
+
'''(H5.2)'''
:Size of armor angle:  Vertical leg of angle shall be a minimum of [[Image:751.50 circled 2.gif]] + 3/4"Horizontal leg of angle shall be a minimum of 3".  Minimum thickness of angle shall be 1/2".
+
:Plan dimensions are based on installation at 60&deg;FThe expansion gap and other dimensions shall be increased or decreased <u>&nbsp;&nbsp;&nbsp;</u>" for each 10&deg; fall or rise in temperature at installation.
  
'''(H5.39)'''
+
'''(H5.3)'''
:If a seal size larger than that indicated on the plans is used, the movement range, the opening at 60&deg; and all dimensions for the armor angles shall be shown on the shop drawings.
+
:Material for the expansion device shall be ASTM A709 Grade 36 structural steel.  Anchors for the expansion device shall be in accordance with Sec 1037.
  
==== H5d. Strip Seal ====
+
'''(H5.4)'''
 +
:Structural steel for the expansion device and barrier plate shall be coated with a minimum of two coats of inorganic zinc primer to provide a total dry film thickness of 4 mils minimum, 6 mils maximum, or galvanized in accordance with ASTM A123. Anchors need not be protected from overspray.
  
'''(H5.46)'''
+
'''(H5.5)'''
:Expansion joint system shall be fabricated in one section, except for stage construction and when the length is over 50 feet.  A complete joint penetration groove welded splice shall be required.  Welds shall be ground flush to provide a smooth surface. The expansion joint system shall be fabricated and installed to the crown and grade of the roadway.
+
:Payment for furnishing, coating or galvanizing and installing the structural steel for the expansion device will be considered completely covered by the contract unit price for Expansion Device (Finger Plate) per linear foot.
 
:The strip seal gland shall be installed in joints in one continuous piece without field splices.  Factory splicing will be permitted for joints in excess of 53 feet.
 
  
'''(H5.47)'''
+
'''(H5.6)'''
:Plan dimensions are based on installation at 60&deg;FThe expansion gap and other dimensions shall be increased or decreased <u>&nbsp;&nbsp;&nbsp;</u>" for each 10&deg; fall or rise in temperature at installation.
+
:Concrete shall be forced under and around finger plate supporting hardware, anchors, angles and bars. Proper consolidation shall be achieved by localized internal vibration.
 +
<div id="(H5.7)"></div>
 +
'''(H5.7)  Use note for steel structures. Use underlined portion when drainage trough is used.'''
 +
:All holes shown for connections shall be subpunched 11/16-inch diameter (shop or field drill) and reamed to 13/16-inch diameter in field, except holes in members that will be used as templates <u>and holes for the drainage trough</u> may be drilled to 13/16-inch diameter in the shop. For multi-piece connections, only the holes in the template member may be drilled to 13/16-inch diameter in the shop.
  
'''(H5.48''')
+
'''(H5.8)  Place note near "Plan of Slab".'''
:Structural steel for the expansion joint system shall be ASTM A709 Grade 36 except the steel armor may be ASTM A709 Grade 50W.  Anchors for the expansion joint system shall be in accordance with Sec 1037. Strip seal expansion joint system shall be in accordance with Sec 717.
+
:'''"the web of W14 x 43" is for steel structures'''
 +
:'''"the 3/4" vertical mounting plate" is for P/S structures.'''
 +
:Longitudinal reinforcing steel shall be placed so that ends shall not be more than &plusmn;1" from <u>the web of W14 x 43</u> <u>and</u> <u>the 3/4" vertical mounting plate</u> at the expansion device.
  
'''(H5.49)'''
+
'''(H5.9)'''
:Structural steel for the expansion joint system shall be coated with a minimum of two coats of inorganic zinc primer (5 mils minimum) or galvanized in accordance with ASTM A123. Anchors need not be protected from overspray.
+
:Complete joint penetration welds utilized in the fabrication of the expansion device shall be nondestructively tested by an approved method.
  
'''(H5.50)'''
+
'''(H5.10)'''  
:Concrete shall be forced under and around steel armor and anchors. Proper consolidation of the concrete shall be achieved by localized internal vibration.
+
:Barrier plate anchors shall be a drilled cone expansion or a cast-in-place wing type threaded insert. The minimum ultimate pullout capacity for these anchors shall be 2700 lbs in f'c = 4000 psi concrete. Lead anchors will not be permitted. Holes in the barrier for anchors shall not be drilled until the concrete is at least 7 days old.
  
'''(H5.51) Place this note near "Plan of Slab".'''
+
==== H5b. Flat Plate ====
:Longitudinal reinforcing steel shall be placed so that ends shall not be more than &plusmn;1" from vertical leg of the steel armor at the expansion joint system.
 
  
'''(H5.53) Use note with polymer concrete next to strip seal.'''
+
'''(H5.16)'''
:Polymer concrete shall be in accordance with Sec 623.
+
:Expansion device shall be fabricated in one section, except for stage construction and when the length is over 50 feet.  A complete joint penetration groove welded splice shall be required.  Welds shall be ground flush to provide a smooth surface.  The expansion device shall be fabricated and installed to the crown and grade of the roadway.
  
=== H6. Pouring and Finishing Concrete Slabs ===
+
'''(H5.17)'''
 +
:Plan dimensions are based on installation at 60&deg;F.  The expansion gap and other dimensions shall be increased or decreased <u>&nbsp;&nbsp;&nbsp;</u>" for each 10&deg; fall or rise in temperature at installation.
  
'''I-Beam, Plate Girder Bridges - Continuous Slabs'''
+
'''(H5.18)'''
 +
:Material for the expansion device shall be ASTM A709 Grade 36 structural steel.  Anchors for the expansion device shall be in accordance with Sec 1037.
  
'''(H6.1)'''
+
'''(H5.19)'''
:The contractor shall pour and satisfactorily finish the slab pours at the rate given.  Retarder, if used, shall be an approved type and retard the set of concrete to 2.5 hours.
+
:Structural steel for the expansion device and barrier plate shall be coated with a minimum of two coats of inorganic zinc primer to provide a total dry film thickness of 4 mils minimum, 6 mils maximum, or galvanized in accordance with ASTM A123. Anchors need not be protected from overspray.
  
 +
'''(H5.20)'''
 +
:Payment for furnishing, coating or galvanizing and installing the structural steel for the expansion device will be considered completely covered by the contract unit price for Expansion Device (Flat Plate) per linear foot.
  
'''Prestressed Concrete Structures - Continuous Spans'''
+
'''(H5.21)'''
 +
:Concrete shall be forced under and around the flat plate, anchors and angles.  Proper consolidation shall be achieved by localized internal vibration.  Finishing of the concrete shall be achieved by hand finishing within one foot of the expansion device.  The vertical and horizontal concrete vent holes shall be offset from each other.  Do not alternate holes at the 12" spacing.
  
'''(H6.4)'''
+
'''(H5.22) Use this note when expansion device is at an end bent.'''
:The contractor shall furnish an approved retarder to retard the set of the concrete to 2.5 hours and shall pour and satisfactorily finish the slab pours at the rate given.
+
:Bevel plates shall be used at end bents when the grade of the slab at the expansion device is 3% or more.
  
'''(H6.5)'''
+
'''(H5.23) Place this note near "Plan of Slab".'''
:End diaphragms at expansion devices may be poured with a construction joint between the diaphragm and slab, or monolithic with the slab.
+
:Longitudinal reinforcing steel shall be placed so that ends shall not be more than &plusmn;1" from <u>vertical plate</u> <u>and</u> <u>the vertical leg of the angle</u> at the expansion device.
  
'''(H6.6) Omit integral end bents with non-integral end bents and intermediate bents with single spans.  Make bents singular if applicable.'''
+
'''(H5.24)'''
:The concrete diaphragm at the <u>intermediate bents</u> <u>and integral</u> <u>end bents</u> shall be poured a minimum of 30 minutes and a maximum of 2 hours before the slab is poured.
+
:Complete joint penetration welds utilized in the fabrication of the expansion device shall be nondestructively tested by an approved method.
  
 +
'''(H5.25)'''
 +
:Barrier plate anchors shall be a drilled cone expansion or a cast-in-place wing type threaded insert.  The minimum ultimate pullout capacity for these anchors shall be 2700 lbs in f'c = 4000 psi concrete.  Lead anchors will not be permitted.  Holes in the barrier for anchors shall not be drilled until the concrete is at least 7 days old.
  
'''Prestressed Double-Tee Concrete Structures'''
+
==== H5c. Preformed Compression Seal ([[#G3. Vertical Drain at End Bent (Notes for Bridge Standard Drawings)|Notes for Bridge Standard Drawings]]) ====
  
'''(H6.9)'''
+
'''(H5.31)'''
:The diaphragms at the intermediate and end bents shall be poured a minimum of 30 minutes and a maximum of 2 hours before the slab is poured across the diaphragm at bents.
+
:Expansion joint system shall be fabricated in one section, except for staged construction and when the length is over 50 feet.  A complete joint penetration groove welded splice shall be required.  Welds shall be ground flush to provide a smooth surface.  The expansion joint system shall be fabricated and installed to the crown and grade of the roadway.
  
'''(H6.10)'''
+
'''(H5.33)'''
:The contractor shall furnish an approved retarder to retard the set of the concrete to 2.5 hours and shall pour and satisfactorily finish the slab pours at not less than 25 cubic yards per hour.
+
:Structural steel for the expansion joint system shall be ASTM A709 Grade 36.  Anchors for the expansion joint system shall be in accordance with Sec 1037. Preformed compression seal expansion joint system shall be in accordance with Sec 717.
  
 +
'''(H5.34)'''
 +
:Structural steel for the expansion joint system shall be coated with a minimum of two coats of inorganic zinc primer to provide a total dry film thickness of 4 mils minimum, 6 mils maximum, or galvanized in accordance with ASTM A123. Anchors need not be protected from overspray.
  
'''Solid or Voided Slab Structure - Continuous and Simple Spans'''
+
'''(H5.35)'''
 +
:Concrete shall be forced under armor angle and around anchors. Proper consolidation of the concrete shall be achieved by localized internal vibration.
  
'''(H6.13) [[751.10_General_Superstructure#751.10.1.12_Slab_Pouring_Sequences_and_Construction_Joints|(*) See EPG 751.10.1.12 Slab Pouring Sequences and Construction Joints]]'''
+
'''(H5.36) Place this note near "Plan of Slab" also.'''  
:The contractor shall furnish an approved retarder to retard the set of the concrete to 2.5 hours and shall pour and satisfactorily finish the roadway slab at a rate of not less than <u>(*)</u> cubic yards per hour.  The contractor shall observe the transverse construction joints shown on the plans, unless the contractor is equipped to pour and satisfactorily finish the roadway slab at a rate which permits a continuous pouring through some or all joints as approved by the engineer.
+
:Longitudinal reinforcing steel shall be placed so that ends shall be 1" from the vertical leg of the angle at the expansion joint system.  
  
  
'''Steel and Prestressed Structures - Simple Spans'''
+
'''Place the following notes (H5.37 and H5.38) near the "Table of Transverse Preformed Compression Seal Expansion Joint System Dimensions".'''
  
'''(H6.15)'''
+
'''(H5.37)'''
:The contractor shall pour and satisfactorily finish the roadway slab at a rate of not less than 25 cubic yards per hour.
+
:Depth of seal shall not be less than width of seal.
  
 +
'''(H5.38) '''
 +
:Size of armor angle: Vertical leg of angle shall be a minimum of Manufacturer’s Recommended Height ③ + 3/4". Horizontal leg of angle shall be a minimum of 3". Minimum thickness of angle shall be 1/2".
  
Widen, Extension, Repair, and Stage Construction
+
'''(H5.39)'''
 +
:The installation temperature shall be taken as the actual air temperature averaged over the 24-hour period immediately preceding installation.
  
'''(H6.17) Underline part not required when forms stay-in-place permanently. Place note on the plans when the closure pour is specified on the design layout.'''
+
'''(H5.40)'''
:Expansive Class B-2 concrete shall be used in the closure pour.  <u>Forms shall be released before the closure pour.</u>
+
:MoDOT Construction personnel will record the manufacturer and seal name that was used.
  
 +
==== H5d. Strip Seal ([[#G3. Vertical Drain at End Bent (Notes for Bridge Standard Drawings)|Notes for Bridge Standard Drawings]])====
  
'''All Structures with Longitudinal Construction Joints'''
+
'''(H5.46)'''
 +
:Expansion joint system shall be fabricated in one section, except for staged construction and when the length is over 50 feet.  A complete joint penetration groove welded splice shall be required.  Welds shall be ground flush to provide a smooth surface. The expansion joint system shall be fabricated and installed to the crown and grade of the roadway.
 +
 +
:The strip seal gland shall be installed in joints in one continuous piece without field splices.  Factory splicing will be permitted for joints in excess of 53 feet.
  
'''(H6.18) The following note shall be used on all structures with slabs wider than 54' containing a longitudinal construction joint.  The blank space shall be replaced by the value corresponding to the total roadway width divided by the larger pour width when the construction joint is used.'''
+
'''(H5.48''')
:The longitudinal construction joint may be omitted with the approval of the engineerWhen the longitudinal construction joint is omitted, the minimum rate of pour for alternate pouring sequences shall be increased by a factor of ____.
+
:Structural steel for the expansion joint system shall be ASTM A709 Grade 36 except the steel armor may be ASTM A709 Grade 50WAnchors for the expansion joint system shall be in accordance with Sec 1037. Strip seal expansion joint system shall be in accordance with Sec 717.
  
=== H7. Slab Drains ===
+
'''(H5.49)'''
 +
:Structural steel for the expansion joint system shall be coated with a minimum of two coats of inorganic zinc primer to provide a total dry film thickness of 4 mils minimum, 6 mils maximum, or galvanized in accordance with ASTM A123. Anchors need not be protected from overspray.
  
'''(H7.1)'''
+
'''(H5.50)'''
:Slab drains may be fabricated of either 1/4" welded sheets of ASTM A709 Grade 36 steel or from 1/4" structural steel tubing ASTM A500 or A501.
+
:Concrete shall be forced under and around steel armor and anchors. Proper consolidation of the concrete shall be achieved by localized internal vibration.
  
'''(H7.1.1)'''
+
'''(H5.51) Place this note near "Plan of Slab" also.'''
:Slab drain bracket assembly shall be ASTM A709 Grade 36 steel.
+
:Longitudinal reinforcing steel shall be placed so that ends shall be 1" from the vertical leg of the steel armor at the expansion joint system.
  
'''(H7.1.2)'''  
+
'''(H5.52)'''  
:The bracket assembly shall be galvanized in accordance with ASTM A123.
+
:The installation temperature shall be taken as the actual air temperature averaged over the 24-hour period immediately preceding installation.  
  
'''(H7.1.3) '''
+
'''(H5.53)'''
:The drains shall be galvanized in accordance with ASTM A123.
+
:MoDOT Construction personnel will indicate the strip seal expansion joint system installed.
  
'''(H7.2) Use with wearing surface.'''
+
'''(H5.54)'''
:Outside dimensions of drain<u>s are 8" x 4"</u> <u>piece "A" is 8 3/4" x 4 3/4" and piece "B" = 8" x 4"</u>.
+
:Steel armor may also be referred to as extrusion or rail.
  
'''(H7.3) Use with new wearing surface over new slab.'''
+
'''(H5.55) Use this note when polymer concrete is to be used next to strip seal.'''
:Piece "A" shall be cast in the concrete slab.  Prior to placement of wearing surface, piece "B" shall be inserted into piece "A".
+
:Polymer concrete shall be in accordance with Sec 623.
  
'''(H7.4)'''
+
====H5e. [[751.13 Expansion Devices#751.13.1.1 General|Preformed Silicone or EPDM Seal]] ([[#G3. Vertical Drain at End Bent (Notes for Bridge Standard Drawings)|Notes for Bridge Standard Drawings]])====
:Locate drain<u>s piece "A"</u>(*) in slab by dimensions shown in Part Section Near Drain.
 
  
'''(H7.5)'''
+
'''(H5.56)'''
:Reinforcing steel shall be shifted to clear drains.
+
:The seal shall be installed in joints in one continuous piece without field splices. Factory splicing will be permitted for joints in excess of 53 feet.  
  
'''(H7.6)'''
+
'''(H5.58)'''  
:The drain<u>s pieces "A" and "B",</u> (*) <u>coil inserts, spacer and bracket assembly</u> shall be galvanized in accordance with ASTM A123.
+
:The installation temperature shall be taken as the actual air temperature averaged over the 24-hour period immediately preceding installation.  
  
'''(H7.7)'''
+
'''(H5.59)'''
:All bolts, hardened washers, lock washers and nuts shall be galvanized in accordance with ASTM A153.
+
:MoDOT Construction personnel will indicate the type of seal used.
  
'''(H7.8) Use “coil insert required” for prestressed girders, “coil inserts required” for prestressed beams and “bolt hole” for steel structures. '''
+
'''(H5.60) Use this note when polymer concrete is to be used next to Preformed Silicone or EPDM Seal. '''
:The <u>coil inserts required</u> <u>bolt hole</u> for the bracket assembly attachment shall be located on the <u>prestressed girder</u> <u>prestressed beam</u> <u>plate girder</u> <u>wide flange beam</u> shop drawings.
+
:Polymer concrete shall be in accordance with Sec 623.
  
'''(H7.9)'''
+
'''(H5.61) Use this note when joint gap (opening) is wider than 3”.'''
:Shop drawings will not be required for the slab drains <u>and the</u> <u>bracket assembly</u>.
+
:Joint gap (opening) wider than 3" during installation may require use of backer rod to keep seal in place while adhesive is curing.
  
(*) Use with wearing surface.
+
====H5f. Open Cell Foam Joint Seal (Notes for Bridge Standard Drawings)====
  
 +
'''(H5.62)'''
 +
:Open cell foam joint seal size (width and depth) shall be determined by the manufacturer.
 +
:Manufacturer recommended seal size shall meet the movement and installation gap requirements and skew effect.
  
'''Place the following notes (H7.10) and (H7.11) with prestressed girder and prestressed beam slab drain details.'''
+
'''(H5.63)'''
 +
:The open cell foam joint seal shall be installed according to the manufacturer's recommendations.
  
'''(H7.10)'''
+
'''(H5.64)'''
:Coil inserts shall have a concrete pull-out strength (Ultimate load) of at least 2,500 pounds in 5,000 psi concrete.
+
:The installation temperature shall be taken as the actual air temperature averaged over the 24-hour period immediately preceding installation.
  
'''(H7.11) Prestressed box and slab beams require two bolts.'''
+
'''(H5.65)'''
:The bolts required to attach the slab drain bracket assembly to the prestressed <u>girder web</u> <u>beam</u> shall be supplied by the prestressed <u>girder</u> <u>beam</u> fabricator.
+
:MoDOT construction personnel will record the manufacturer and seal name that was used.
  
'''(H7.12)'''
+
=== H6. Pouring and Finishing Concrete Slabs ===
:The bolt hole for the bracket assembly attachment shall be located on the plate girder shop drawings.
 
  
'''<u>Use following notes when Fiberglass Reinforced Polymer (FRP) slab drains are used.</u>'''
+
'''I-Beam, Plate Girder Bridges - Continuous Slabs'''
  
'''(H7.13) '''
+
'''(H6.1)'''
:Contractor shall have the option to construct either steel or FRP slab drains. All drains shall be of same type.  
+
:The contractor shall pour and satisfactorily finish the slab pours at the rate given. Retarder, if used, shall be an approved type and retard the set of concrete to 2.5 hours.
  
'''(H7.14) '''
 
:Drains shall be machine filament-wound thermosetting resin tubing meeting the requirements of ASTM D2996 with the following exceptions:
 
  
'''(H7.15) '''
+
'''Prestressed Concrete Structures - Continuous Spans'''
:Shape of  drains shall be rectangular with outside interior nominal dimensions of 8” x 4”.
 
  
'''(H7.16) '''
+
'''(H6.4)'''
:Minimum reinforced wall thickness shall be of 1/4 inch.
+
:The contractor shall furnish an approved retarder to retard the set of the concrete to 2.5 hours and shall pour and satisfactorily finish the slab pours at the rate given.
  
'''(H7.17) '''
+
'''(H6.5)'''
:The resin used shall be ultraviolet (UV) resistant and/or have UV inhibitors mixed throughout. Drains may have an exterior coating for additional UV resistance.
+
:End diaphragms at expansion devices may be poured with a construction joint between the diaphragm and slab, or monolithic with the slab.
  
'''(H7.18) '''
+
'''(H6.6) Note is not applicable for concrete diaphragms under expansion joints.'''
:The color of the slab drain shall be Gray (Federal Standard #26373). The color shall be uniform throughout the resin and any coating used.
+
:The concrete diaphragm at the <u>intermediate bents</u> <u>and integral</u> <u>end bents</u> shall be poured a minimum of 30 minutes and a maximum of 2 hours before the slab is poured.
  
'''(H7.19) '''
 
:The combination of materials used in the manufacture of the drains shall be tested for UV resistance in accordance with ASTM D4239 Cycle A. The representative material shall withstand at least 500 hours of testing with only minor discoloration and without any physical deterioration. The contractor shall furnish the results of the required ultraviolet testing prior to acceptance of the slab drains.
 
  
'''(H7.20) '''
+
'''Prestressed Double-Tee Concrete Structures'''
:At the contractor’s option, drains may be field cut. The method of cutting FRP slab drains shall be as recommended by the manufacturer to ensure a smooth, chip free cut.
 
 
'''(H7.21) Use only for angled drains. '''
 
:Both upper and lower drain pieces shall be rigidly connected to each other. Drain flow shall not be obstructed. Approval of the engineer is required.
 
  
'''(H7.22) '''
+
'''(H6.9)'''
:No additional payment will be made for this substitution.
+
:The diaphragms at the intermediate and end bents shall be poured a minimum of 30 minutes and a maximum of 2 hours before the slab is poured across the diaphragm at bents.
  
=== H8. Blank ===
+
'''(H6.10)'''
 +
:The contractor shall furnish an approved retarder to retard the set of the concrete to 2.5 hours and shall pour and satisfactorily finish the slab pours at not less than 25 cubic yards per hour.
  
  
=== H9. Thrie Beam and Other Rail Types ===
+
'''Solid or Voided Slab Structure - Continuous and Simple Spans'''
  
'''(H9.1a) Use for all W-Beam, Thrie Beam, Two Tube and Single Tube (Low Profile) Structural Steel Guardrails without cap rail.  (See [[620.5 Delineators (MUTCD Chapter 3F)#620.5.5 Guardrail Delineation|Guardrail Delineation]].)''' (See [[751.50 Standard Detailing Notes#H10a. Safety, Median, Type C & D|Note H10.7.1]] Guidance for using Part Note for Delineation Sheeting Requirements.)
+
'''(H6.13) [[751.10_General_Superstructure#751.10.1.12_Slab_Pouring_Sequences_and_Construction_Joints|(*) See EPG 751.10.1.12 Slab Pouring Sequences and Construction Joints]]'''
 +
:The contractor shall furnish an approved retarder to retard the set of the concrete to 2.5 hours and shall pour and satisfactorily finish the roadway slab at a rate of not less than <u>(*)</u> cubic yards per hour.  The contractor shall observe the transverse construction joints shown on the plans, unless the contractor is equipped to pour and satisfactorily finish the roadway slab at a rate which permits a continuous pouring through some or all joints as approved by the engineer.
  
:Guardrail delineators shall be attached to the top of the guardrail post using galvanized anchorage as shown on Missouri Standard Plan 606.00 and in accordance with Sec 606.  <u>Delineators on bridges with two-lane, two-way traffic shall have retroreflective sheeting on both sides.</u>  Guardrail delineators will be considered completely covered by the contract unit price for <u>Bridge Guardrail (W-Beam)</u>, <u>Bridge Guardrail (Thrie Beam)</u>, <u>Bridge Rail (Two Tube Structural Steel)</u>, <u>Low Profile Metal Bridge Rail (Single Tube)</u>.
 
  
'''(H9.1b) Use for all W-Beam and Thrie Beam Guardrails with cap rail. (See [[620.5 Delineators (MUTCD Chapter 3F)#620.5.5 Guardrail Delineation|Guardrail Delineation]].)''' (See [[751.50 Standard Detailing Notes#H10a. Safety, Median, Type C & D|Note H10.7.1]] Guidance for using Part Note for Delineation Sheeting Requirements.)
+
'''Steel and Prestressed Structures - Simple Spans'''
  
:Guardrail delineators shall be attached to the top of the guardrail and shall similarly use the delineator details of Missouri Standard Plan 617.10, except that the delineator body shall be attached to the top of the cap rail using galvanized anchorage as shown on Missouri Standard Plan 606.00.  <u>Delineators on bridges with two-lane, two-way traffic shall have retroreflective sheeting on both sides.</u>  Guardrail delineators will be considered completely covered by the contract unit price for <u>Bridge Guardrail (W-Beam)</u>, <u>Bridge Guardrail (Thrie Beam).</u>
+
'''(H6.15)'''
 +
:The contractor shall pour and satisfactorily finish the roadway slab at a rate of not less than 25 cubic yards per hour.
  
'''(H9.2)'''
 
:Panel lengths of channel members shall be attached continuously to a minimum of four posts and a maximum of six posts (except at end bents).
 
  
'''(H9.3)'''
+
'''Widen, Extension, Repair, and Stage Construction'''
:All bolts, nuts, washers, plates, reinforcement <u>and elastomeric materials</u> will be considered completely covered by the contract unit price for <u>Bridge</u> <u>Guardrail (W-Beam)</u> <u>Bridge Guardrail (Thrie Beam)</u> <u>other items</u>.
 
  
'''(H9.4Use underline part for temporary bridges.'''
+
'''(H6.17Underline part not required when forms stay-in-place permanently. Place note on the plans when the closure pour is specified on the design layout.'''
:All steel connecting bolts and fasteners for posts and railing, and all anchor bolts, nuts, washers and plates shall be galvanized after fabrication <u>except for bottom plate</u>.  Protective coating and material requirement of steel railing shall be in accordance with Sec 1040.
+
:Expansive Class B-2 concrete shall be used in the closure pour.  <u>Forms shall be released before the closure pour.</u>
  
'''(H9.5)  Use post instead of blockout for temporary bridges'''.
 
:Rail posts shall be set perpendicular to roadway profile grade, vertically in cross section and aligned in accordance with Sec 713 except that the rail posts shall be aligned by the use of shims such that the post deviates not more than 1/2 inch from true horizontal alignment after final adjustment.  The shims shall be 3" x 1 3/4"  and placed between the <u>blockout</u> <u>post</u> and the thrie beam rail. The thickness of the shims shall be determined by the contractor and verified by the engineer before ordering material for this work.
 
  
'''(H9.6) Use only when a base plate is used.'''
+
'''All Structures with Longitudinal Construction Joints'''
:Rail posts shall be seated on elastomeric pads having the same dimensions as the post base plate and 1/16" thickness.  Such pads may be any elastomeric material, plain or fibered, having hardness (Durometer) of 50 or above, as certified by the manufacturer.  Additional pads or half pads may be used in shimming for alignment.  Post heights shown will increase by the thickness of the pad.
 
  
'''(H9.7)'''
+
'''(H6.18) The following note shall be used on all structures with slabs wider than 54' containing a longitudinal construction joint.  The blank space shall be replaced by the value corresponding to the total roadway width divided by the larger pour width when the construction joint is used.'''
:At the expansion slots in the thrie beam rails and channels, the bolts shall be tightened and backed off one-half turn and the threads shall be burred.
+
:The longitudinal construction joint may be omitted with the approval of the engineer.  When the longitudinal construction joint is omitted, the minimum rate of pour for alternate pouring sequences shall be increased by a factor of ____.
  
'''(H9.8)'''
 
:At the thrie beam connection to blockout on wings, the bolts shall be tightened and backed off one-half turn and the threads shall be burred.
 
  
'''(H9.9)'''
+
<div id="Wide Flange Deck Replacements"></div>
:Minimum length of thrie beam sections is equal to one post space.
+
'''Wide Flange Deck Replacements'''
 +
 +
'''(H6.20)'''
 +
:The contractor shall provide bracing necessary for lateral and torsional stability of the beams during construction of the concrete slab and remove the bracing after the slab has attained 75% design strength. Contractor shall not weld on or drill holes in the beams. The cost for furnishing, installing, and removing bracing will be considered completely covered by the contract unit price for Slab on Steel.
  
'''(H9.10)'''
+
'''(H6.21)'''
:5/8"&oslash; button-head, oval shoulder bolts with 3/8" min. thickness hex nuts shall be used at all slots.
+
:Slab shall be poured upgrade from end to end at a minimum rate of 25 cubic yards per hour.
  
'''(H9.11)'''
+
'''(H6.22)'''
:Thrie beam guardrail on the bridge shall be 12 gage steel.
+
:Alternate pour sequences may be submitted to the engineer for approval. Keyed construction joints shall be provided between pours.
  
'''(H9.12) Use top plates instead of cap rail angles for temporary bridges.'''
+
=== H7. Slab Drains (Notes for Bridge Standard Drawings)===
:Posts, <u>cap rail angles,</u> <u>top plates,</u> <u>base</u> <u>bent</u> <u>post</u> plates, channels and channel splice plates shall be fabricated from ASTM A709 Grade 36 steel and galvanized.
 
<div id="(H9.13) Use for placement"></div>
 
  
'''(H9.13) Use for placement or replacement of end treatment with thrie beam rail.'''
+
'''When steel slab drains are used place Notes H7.1, H7.1.3 and H7.2 under the heading of Notes for Steel Drain. Place remaining notes thru Note H7.11 under the heading of General Notes.'''
:<u>Cost for providing holes for new guardrail attachment will be considered completely covered by the contract unit price for other items.</u>
 
  
'''(H9.15) Use post instead of blockout for temporary bridges.'''
+
'''(H7.1)'''
:Washers shall be used at all post bolts between the bolt head and beam.  The flat washers shall be rectangular in shape, 3" x 1 3/4" x 3/16" minimum and with a 11/16" x 1" slot, or when necessary of such design as to fit the contour of the beam.  A 3" x 1 3/4" x 5/8" rectangular washer shall be used between the <u>blockout</u> <u>post</u> and the thrie beam rail.
+
:Slab drains may be fabricated of either 1/4" welded sheets of ASTM A709 Grade 36 steel or from 1/4" structural steel tubing ASTM A500 or A501.
  
'''(H9.16)'''
+
'''(H7.1.1) Note not required for continuous concrete slab bridges. '''
:Special drilling of the thrie beam may be required at the splices.  All drilling details shall be shown on the shop drawings.
+
:Slab drain bracket assembly shall be ASTM A709 Grade 36 steel.
  
'''(H9.17''')
+
'''(H7.1.3) Use underlined portion with a wearing surface. '''
:Fabrication of structural steel shall be in accordance with Sec 1080.
+
:The drain<u>s Pieces A and B</u> shall be galvanized in accordance with ASTM A123.
  
'''(H9.18) Do not use with prestress double-tee or temporary bridge structures.'''
+
'''(H7.2) Use first choice without a wearing surface and second choice with a wearing surface.'''
:Expansion splices in the thrie beam rail shall be made at either the first or second post on either side of the joint and on structure at bridge ends.  When the splice is made at the second post, an expansion slot shall be provided in the thrie beam rail for connection to the first post to allow for movement.
+
:Outside dimensions of drain<u>s are 8" x 4"</u> <u>Piece A is 8 3/4" x 4 3/4" and Piece B is 8" x 4"</u>.
  
'''(H9.19) Do not use with prestressed double-tee or temporary bridge structures.'''
+
'''(H7.3) Use note with new wearing surface over new slab.'''
:In addition to the expansion provisions at the expansion joints, expansion splices in the thrie beam rail and the channel shall be provided at other locations so that the maximum length without expansion provisions does not exceed 200 ft.
+
:Piece A shall be cast in the concrete slab.  Prior to placement of wearing surface, Piece B shall be inserted into Piece A.
  
 +
'''(H7.4) Use underlined portion with a wearing surface. '''
 +
:Locate drain<u>s Piece A</u> in slab by dimensions shown in Part Section Near Drain.
  
'''Do not use any of the following notes for temporary bridges.'''
+
'''(H7.5)'''
 +
:Reinforcing steel shall be shifted to clear drains.
  
'''(H9.20) Use with prestress double-tee structures.'''
+
'''(H7.6) Use underlined portion with prestressed girders and beams. Note not required for continuous concrete slab bridges. '''
:Expansion splices in the thrie beam rail and the channel shall be provided at locations so that the maximum length without expansion provisions does not exceed 200 ft.
+
:The <u>coil inserts and</u> bracket assembly shall be galvanized in accordance with ASTM A123.
  
'''(H9.21)'''
+
'''(H7.7) Use underlined portion with weathering steel girders and beams. Note not required for continuous concrete slab bridges. '''
:Shim plates 6" x 6" x 1/16" may be used between the top of the post and the channel member as required for vertical alignment.
+
:All bolts, hardened washers, lock washers and nuts shall be galvanized in accordance with AASHTO M 232 (ASTM A153), Class C<u>, except as shown</u>.
  
'''(H9.22)'''
+
'''(H7.7.1)'''
:See slab sheet for rail post spacing.
+
:All ½” diameter bolts shall be ASTM A307, except as noted.
  
'''(H9.23)'''
+
'''(H7.8) Use note when attaching to new girders and beams. Use “coil insert required” for prestressed girders, “coil inserts required” for prestressed beams and “bolt hole” for steel structures. '''
:See Missouri Standard Plans drawing 606.00 for details not shown.
+
:The <u>coil inserts required</u> <u>bolt hole</u> for the bracket assembly attachment shall be located on the <u>prestressed girder</u> <u>prestressed beam</u> <u>plate girder</u> <u>wide flange beam</u> shop drawings.
  
'''(H9.24)'''
+
'''(H7.8.1) Use note when attaching to existing steel girders and beams.'''  
:Bolt shall not be bent in slab depths greater than 14", use 12" straight embeddment.
+
:The bolt hole for the bracket assembly attachment shall be shifted to the minimum extent necessary to field drill in the existing web.
 +
<div id="(H7.8.2) Use note"></div>
 +
'''(H7.8.2) Use note when attaching to weathering steel girders and beams. '''
 +
:The galvanized surfaces of drain support brackets shall be prepared according to the coating manufacturer's recommendation and field coated with a gray epoxy-mastic primer (non-aluminum) within a distance of 6 inches from the point of connection to the weathering steel structure.
  
'''(H9.25)'''
+
'''(H7.9) Use the underline portion for all bridges except continuous concrete slab bridges. '''
:Shim plates 6" x 3" x 1/16" may be used between post W6x20 and 1/2" bent plate connection as required for horizontal alignment.
+
:Shop drawings will not be required for the slab drains <u>and the bracket assembly</u>.
  
'''(H9.26)'''
 
:Shim plates shall be galvanized after fabrication.
 
  
'''(H9.27)'''
+
'''Place Notes H7.10 and H7.11 with prestressed girder and prestressed beam slab drain details.'''
:Shim plates 6" x 6" x 1/16" may be used between post W6x20 and 6" x 6" x 3/8" plate and shim plates 6" x 3 1/2" x 1/16" may be used between post W6x20 and 1/2" bent plate connection as required for horizontal alignment.
 
  
'''(H9.28)'''
+
'''(H7.10)'''
:Bar supports shall be Beam Bolsters (BB-ref. CRSI) and shall be galvanized. See Sec 706.
+
:Coil inserts shall have a concrete pull-out strength (ultimate load) of at least 2,500 pounds in 5,000 psi concrete.
  
 +
'''(H7.11) Bolts is plural for Prestressed box and slab beams that require two bolts.'''
 +
:The bolt<u>s</u> required to attach the slab drain bracket assembly to the prestressed <u>girder web</u> <u>beam</u> shall be supplied by the prestressed <u>girder</u> <u>beam</u> fabricator.
  
'''Use the following notes where required and with temporary bridges thrie beam sheet.'''
 
  
'''(H9.30''')
+
'''Use Notes H7.13 thru H7.21 when fiberglass reinforced polymer (FRP) slab drains are used. Place Note H7.13 as the first note under the heading of General Notes. Place remaining notes under the heading of Notes for FRP Drain.'''
:Note deleted.
 
  
'''(H9.31)'''
+
'''(H7.13) '''
:If type "A" guardrail is not attached to ends of the temporary structure, flared ends shall be required. The existing thrie beam rails shall be modified to accept flared ends. Cost for furnishing and installing flared ends will be considered completely covered by the contract unit price for other items.
+
:Contractor shall have the option to construct either steel or FRP slab drains. All drains shall be of same type.  
  
'''(H9.32)'''
+
'''(H7.14) '''
:Contractor shall verify all dimensions in field before ordering materials.
+
:Drains shall be machine filament-wound thermosetting resin tubing meeting the requirements of ASTM D2996 with the following exceptions:
  
'''(H9.33)'''
+
'''(H7.15) '''
:See preceding sheet for rail post spacing.
+
:Shape of  drains shall be rectangular with outside interior nominal dimensions of 8” x 4”.
  
'''(H9.34)'''
+
'''(H7.16) '''
:At the bridge ends for head to head traffic, guardrail shall be used at all four corners and for single directional traffic, guardrail shall be used at the entrance ends only unless required at the exit.
+
:Minimum reinforced wall thickness shall be of 1/4 inch.
  
'''(H9.35)'''
+
'''(H7.17) '''
:Bottom plate shall be fabricated from ASTM A709 Grade 50W steel and welded to two 5" floor bars. Bottom plate shall not be galvanized.
+
:The resin used shall be ultraviolet (UV) resistant and/or have UV inhibitors mixed throughout. Drains may have an exterior coating for additional UV resistance.
  
'''(H9.36)'''
+
'''(H7.18) The standard color shall be Gray (Federal Standard #26373). Optional colors which are the same colors allowed for steel superstructures include <u>Brown (Federal Standard #30045)</u> <u>Black (Federal Standard #17038)</u> <u>Dark Blue (Federal Standard #25052)</u> <u>Bright Blue (Federal Standard #25095)</u>. Consult with FRP drain manufacturer/supplier to verify optional color availability and cost.'''
:The size of the base and bottom plate may be increased depending on which grid option is used.
+
:The color of the slab drain shall be <u>Gray (Federal Standard 26373)</u>. The color shall be uniform throughout the resin and any coating used.
  
'''(H9.37)'''
+
'''(H7.19) '''
:Optional welding of the post to the base plate, in lieu of the weld shown, is a 5/16" fillet weld all around, including the edges of the post flanges.
+
:The combination of materials used in the manufacture of the drains shall be tested for UV resistance in accordance with ASTM D4239 Cycle A. The representative material shall withstand at least 500 hours of testing with only minor discoloration and without any physical deterioration. The contractor shall furnish the results of the required ultraviolet testing prior to acceptance of the slab drains.
  
'''(H9.38)'''
+
'''(H7.20) '''
:Semi-circular notches centered on the axis of the post web ends may be made to facilitate galvanizing.
+
:At the contractor’s option, drains may be field cut. The method of cutting FRP slab drains shall be as recommended by the manufacturer to ensure a smooth, chip free cut.
 +
 +
'''(H7.21) Use only for angled drains. '''
 +
:Both upper and lower drain pieces shall be rigidly connected to each other. Drain flow shall not be obstructed. Approval of the engineer is required.
  
'''(H9.39) Use for all Thrie Beam Guardrails on temporary bridges.''' (See [[751.50 Standard Detailing Notes#H10a. Safety, Median, Type C & D|Note H10.7.1]] Guidance for using Part Note for Delineation Sheeting Requirements.)
+
=== H8. Blank ===
  
:Guardrail delineators shall be attached to the top of the bridge guardrail and shall similarly use the delineator details of Missouri Standard Plan 617.10, except that the delineator body shall be attached to the top of the cap rail using galvanized anchorage as shown on  Missouri Standard Plan 606.00.  <u>Delineators on bridges with two-lane, two-way traffic shall have retroreflective sheeting on both sides.</u>  Cost of supplying and installing new delineators will be considered completely covered by other pay items.  Delineators shall be stored with bridge guardrail after use.
 
  
=== H10. Barrier Curbs ===
+
=== H9. Thrie Beam and Other Rail Types (Notes for Bridge Standard Drawings)===
 +
'''Place in General Notes on the rail sheet unless otherwise specified.'''
  
==== H10a. Safety, Median, Type C & D ====
+
'''(H9.1a) Use for all W-Beam, Thrie Beam, Two Tube and Single Tube (Low Profile) Structural Steel Guardrails without cap rail.  (See [[620.5 Delineators (MUTCD Chapter 3F)#620.5.5 Guardrail Delineation|Guardrail Delineation]].)''' (See [[751.50 Standard Detailing Notes#(H10.7.1) Notes shall be used on all barrier curbs|Note H10.7.1]] Guidance for using Part Note for Delineation Sheeting Requirements.)
  
'''The following notes shall be placed in the General Notes on the elevation sheet of the cast-in-place forming details.'''
+
:Guardrail delineators shall be attached to the top of the guardrail post using galvanized anchorage as shown on Missouri Standard Plan 606.00 and in accordance with Sec 606.  <u>Delineators on bridges with two-lane, two-way traffic shall have retroreflective sheeting on both sides.</u>  Guardrail delineators will be considered completely covered by the contract unit price for <u>Bridge Guardrail (W-Beam)</u> <u>Bridge Guardrail (Thrie Beam)</u> <u>Bridge Rail (Two Tube Structural Steel)</u> <u>Low Profile Metal Bridge Rail (Single Tube)</u>.
  
'''(H10.1)'''
+
'''(H9.1b) Use for all W-Beam and Thrie Beam Guardrails with cap rail except for temporary bridges. (See [[620.5 Delineators (MUTCD Chapter 3F)#620.5.5 Guardrail Delineation|Guardrail Delineation]].)''' (See [[751.50 Standard Detailing Notes#(H10.7.1) Notes shall be used on all barrier curbs|Note H10.7.1]] Guidance for using Part Note for Delineation Sheeting Requirements.)  
:Top of <u>safety</u> <u>median</u> barrier curb <u>(Type C)</u> <u>(Type D)</u> <u>and median barrier curb transition (Type C)</u> shall be built parallel to grade with barrier curb joints <u>(except at end bents)</u> normal to grade.
 
  
'''(H10.2)'''
+
:Guardrail delineators shall be attached to the top of the guardrail and shall similarly use the delineator details of Missouri Standard Plan 617.10, except that the delineator body shall be attached to the top of the cap rail using galvanized anchorage as shown on Missouri Standard Plan 606.00.  <u>Delineators on bridges with two-lane, two-way traffic shall have retroreflective sheeting on both sides.</u> Guardrail delineators will be considered completely covered by the contract unit price for <u>Bridge Guardrail (W-Beam)</u>, <u>Bridge Guardrail (Thrie Beam).</u>
:All exposed edges of <u>safety</u> <u>median</u> barrier curb <u>(Type C)</u> <u>(Type D)</u> <u>and median barrier curb transition (Type C)</u> shall have either a 1/2-inch radius or a 3/8-inch bevel, unless otherwise noted.
 
  
'''(H10.3)'''
+
'''(H9.1c) Use for temporary bridges.''' (See [[751.50 Standard Detailing Notes#(H10.7.1) Notes shall be used on all barrier curbs|Note H10.7.1]] Guidance for using Part Note for Delineation Sheeting Requirements.)
:Payment for all concrete and reinforcement, complete in place, will be considered completely covered by the contract unit price for <u>Safety</u> <u>Median</u> Barrier Curb <u>(Type C)</u> <u>(Type D)</u> per linear foot.
 
  
'''(H10.4)'''
+
:Guardrail delineators shall be attached to the top of the bridge guardrail and shall similarly use the delineator details of Missouri Standard Plan 617.10, except that the delineator body shall be attached to the top of the cap rail using galvanized anchorage as shown on Missouri Standard Plan 606.00. Delineators on bridges with two-lane, two-way traffic shall have retroreflective sheeting on both sides. Cost of supplying and installing new delineators will be considered completely covered by other pay items. Delineators shall be stored with bridge guardrail after use.  
:Concrete in the <u>safety</u> <u>median</u> barrier curb <u>(Type C)</u> <u>(Type D)</u> <u>and median barrier curb transition (Type C)</u> shall be Class B-1.
 
  
'''(H10.5) Use for safety barrier curb or barrier curb (Type D) ending over wing walls. '''
+
'''(H9.2)'''
:Measurement of <u>safety</u> <u>(Type D)</u> barrier curb is to the nearest linear foot <u>for each structure</u>, measured along the outside top of slab from end of wing to end of wing.
+
:Panel lengths of channel members shall be attached continuously to a minimum of four posts and a maximum of six posts (except at end bents).
  
'''(H10.6) Use for safety barrier curb or barrier curb (Type D) not ending over wing walls (two separate curbs used as a median or when wings are flared). '''
+
'''(H9.3) Include reinforcement with new bridges except double-tees and temporary bridges. Include elastomeric material when a base plate is used except for temporary bridges. Use “other items” for temporary bridges. '''
:Measurement of <u>safety</u> barrier curb <u>(Type D)</u> is to the nearest linear foot for each structure, measured along the outside top of slab from <u>end of slab to end of slab</u> <u>Measurement of median barrier curb transition (Type C) is to the nearest linear foot for each structure measured along the top of slab at centerline median from centerline sleeper slab to end of slab.</u>
 
  
'''(H10.7) Use for median barrier curb and median barrier curb (Type C).'''
+
:All bolts, nuts, washers, <u>and</u> plates<u>,</u> <u>and</u> reinforcement <u>and elastomeric material</u> will be considered completely covered by the contract unit price for <u>Bridge</u> <u>Guardrail (W-Beam)</u> <u>Bridge Guardrail (Thrie Beam)</u> <u>other items</u>.
:Measurement of median barrier curb <u>(Type C)</u> is to the nearest linear foot for each structure, measured along the top of slab at centerline median from <u>end of slab to end of slab</u> <u>centerline sleeper slab to centerline sleeper slab</u>.
 
<div id="(H10.7.1) Notes shall be used on all barrier curbs"></div>
 
'''(H10.7.1) Use for all barrier curbs (See [[620.5 Delineators (MUTCD Chapter 3F)#620.5.6 Barrier Wall Delineation|Barrier Wall Delineation]]).'''
 
  
:Concrete traffic barrier delineators shall be placed on top of the <u>safety</u> <u>median</u> barrier curb <u>(Type C)</u> <u>(Type D)</u> <u>and median barrier curb transition (Type C)</u> as shown on Missouri Standard Plans 617.10 and in accordance with Sec 617. <u>Delineators on bridges with two-lane, two-way traffic shall have retroreflective sheeting on both sides.</u> Concrete traffic barrier delineators will be considered completely covered by the contract unit price for <u>Safety</u> <u>Median</u> Barrier Curb <u>(Type C)</u> <u>(Type D)</u>.  
+
'''(H9.4)  Use underlined part for temporary bridges.'''
 +
:All steel connecting bolts and fasteners for posts and railing, and all anchor bolts, nuts, washers and plates shall be galvanized after fabrication <u>except for bottom plate</u>. Protective coating and material requirement of steel railing shall be in accordance with Sec 1040.
  
{|style="padding: 0.3em; margin-left:10px; border:1px solid #a9a9a9; text-align:left; font-size: 95%; background:#f5f5f5" width="760px" align="center"
+
'''(H9.5)  Use post instead of blockout for temporary bridges'''.
|-
+
:Rail posts shall be set perpendicular to roadway profile grade, vertically in cross section and aligned in accordance with Sec 713 except that the rail posts shall be aligned by the use of 3 x 1 3/4-inch shims such that the post deviates not more than 1/2 inch from true horizontal alignment after final adjustment.  The shims shall be placed between the <u>blockout</u> <u>post</u> and the thrie beam rail. The thickness of the shims shall be determined by the contractor and verified by the engineer before ordering material for this work.
|Below is additional guidance for using Part Note for Delineation Sheeting Requirements:  
 
|-
 
|Bridges with two-lane, two-way traffic shall have retroreflective sheeting on both sides of the delineators.  For two-lane, one-way traffic, retroreflective sheeting may be on one side only unless crossroad or entranceway traffic is just beyond exit to bridge and wrong way driving is to be discouraged with retroreflective sheeting on both sides of the delineators, (white and red in this case). "Delineators on bridges with two-lane, two-way traffic shall have retroreflective sheeting on both sides" may be modified, as required. For median barrier curbs, retroreflective sheeting should be used on both sides of the delineators where there is not more than four lanes divided.
 
|-
 
|On bridges with more than two lanes, retroreflective sheeting is not required on both sides of the delineators.  The perception of a narrowing roadway at the bridge is of lesser consequence in terms of requiring guidance devices and does not warrant retroreflective sheeting on both sides of the delineators. "Delineators on bridges with two-lane, two-way traffic shall have retroreflective sheeting on both sides" may be removed at the discretion of the design team.
 
|}
 
  
 +
'''(H9.6) Use only when a base plate is used except for temporary bridges.'''
  
'''The following notes shall be placed under cross-section thru barrier.'''
+
:Rail posts shall be seated on 1/16-inch elastomeric pads having the same dimensions as the post base plate. Such pads may be any elastomeric material, plain or fibered, having hardness (durometer) of 50 or above, as certified by the manufacturer. Additional pads or half pads may be used in shimming for alignment. Post heights shown will increase by the thickness of the pad.  
  
'''(H10.8)'''
+
'''(H9.7)'''
:Use a minimum lap of 2'-11" for #5 horizontal <u>safety</u> <u>median</u> barrier curb <u>(Type C)</u> <u>(Type D)</u> bars.
+
:At the expansion slots in the thrie beam rails and channels, the bolts shall be tightened and backed off one-half turn and the threads shall be burred.
  
'''(H10.9) Areas shown are for standard barrier heights and a 2 percent cross-slope. '''
+
'''(H9.8) Use post instead of blockout for temporary bridges. '''
:The cross-sectional area <u>for each curb</u> above the slab = <u>*</u> sq. ft.
+
:At the thrie beam connection to <u>blockout</u> <u>post</u> on wings, the bolts shall be tightened and backed off one-half turn and the threads shall be burred.
  
:{|
+
'''(H9.9)'''
|*||2.27 for a 16" safety barrier curb.
+
:Minimum length of thrie beam sections is equal to one post space.
|-
 
|||2.98 for a median barrier curb.
 
|-
 
|||3.52 for a barrier curb (Type D).
 
|-
 
|||3.59 for a barrier curb (Type D) used as a median.
 
|-
 
|||4.69 for a median barrier curb (Type C).
 
|}
 
  
 +
'''(H9.10)'''
 +
:A 5/8-inch diameter button-head, oval shoulder bolt with a minimum 3/8-inch thick hex nut shall be used at all slots.
  
'''The following notes shall be used for double-tee structures.'''
+
'''(H9.11)'''
 +
:Thrie beam guardrail on the bridge shall be 12-gauge steel.
  
'''(H10.10)'''
+
'''(H9.12) Use top plates instead of cap rail angles for temporary bridges.'''
:Coil inserts shall have a concrete ultimate pullout strength of not less than 36,000 pounds in 5000 psi concrete and an ultimate tensile strength of not less than 36,000 pounds.
+
:Posts, <u>cap rail angles,</u> <u>top plates,</u> <u>base</u> <u>bent</u> <u>post</u> plates, <u>blockouts,</u> channels and channel splice plates shall be fabricated from ASTM A709 Grade 36 steel and galvanized.
 +
<div id="(H9.13) Use for placement"></div>
  
'''(H10.11)'''
+
'''(H9.13) Use for placement or replacement of end treatment with thrie beam rail.'''
:Threaded coil rods shall have an ultimate capacity of 36,000 pounds.  All coil inserts and threaded coil rods shall be galvanized in accordance with ASTM A153.
+
:<u>Cost for providing holes for new guardrail attachment will be considered completely covered by the contract unit price for other items.</u>
  
'''(H10.12)'''
+
'''(H9.15) Use post instead of blockout for temporary bridges.'''
:Payment for furnishing and installing coil inserts and threaded coil rods will be considered completely covered by the contract unit price for <u>Safety</u> <u>Median</u> Barrier Curb <u>(Type C)</u> <u>(Type D)</u>.
+
:Flat washers 3 x 1 3/4 x 3/16-inch minimum shall be used at all post bolts between the bolt head and beam. The washers shall be rectangular in shape with an 11/16 x 1-inch slot, or when necessary of such design as to fit the contour of the beam.  Rectangular washers 3 x 1 3/4 x 5/8-inch shall be used between the <u>blockout</u> <u>post</u> and the thrie beam rail.
  
 +
'''(H9.16)'''
 +
:Special drilling of the thrie beam may be required at the splices.  All drilling details shall be shown on the shop drawings.
  
'''The following notes, when appropriate, shall be placed under the title of the elevation of barrier of the cast-in-place forming details. '''
+
'''(H9.17''')
 +
:Fabrication of structural steel shall be in accordance with Sec 1080.
  
'''(H10.12.1)'''
+
'''(H9.18) Do not use for prestressed double-tee or temporary bridges.'''
:Longitudinal dimensions are <u>horizontal</u> <u>arc dimensions</u>.
+
:Expansion splices in the thrie beam rail shall be made at either the first or second post on either side of the joint and on structure at bridge ends.  When the splice is made at the second post, an expansion slot shall be provided in the thrie beam rail for connection to the first post to allow for movement.
  
'''(H10.12.2)'''
+
'''(H9.19) Do not use for prestressed double-tee or temporary bridges.'''
:Longitudinal dimensions are along top of <u>safety barrier curb</u> <u>outside</u> <u>edge of slab</u> parallel to grade.
+
:In addition to the expansion provisions at the expansion joints, expansion splices in the thrie beam rail and the channel shall be provided at other locations so that the maximum length without expansion provisions does not exceed 200 feet.
  
'''The following reference notes shall be placed under the permissible alternate bar shape detail.'''
 
  
'''(H10.13) Use R2 for Type D curbs, R3 for safety barrier curbs and M2 for two separate Type D curbs used as a median. '''
+
'''Do not use Notes H9.20 thru H9.29 for temporary bridges. '''
:<math>\, **</math> The <u>R2</u> <u>R3</u> <u>M2</u> bar and #5 bottom transverse slab bar in cantilever (P/S panels only) combination may be furnished as one bar as shown, at the contractor's option.
 
  
'''(H10.14) Use R1 for safety barrier curbs and Type D curbs. Use M1 for two separate Type D curbs used as a median.'''
+
'''(H9.20) Use for prestressed double-tee bridges. '''
:(<math>\, *</math>) The <u>R1</u> <u>M1</u> bar may be separated into two bars as shown, at the contractor's option, only when slip forming is not used. (All dimensions are out to out.)
+
:Expansion splices in the thrie beam rail and the channel shall be provided at locations so that the maximum length without expansion provisions does not exceed 200 feet.
  
'''The following notes and H10.7.1 shall be placed with the details of the barrier at end bents.'''
+
'''(H9.21)'''
 +
:Shim plates 6 x 6 x 1/16-inch may be used between the top of the post and the channel member as required for vertical alignment.  
  
'''(H10.20) Add K13 bars with two different wing lengths. Will need to add more bars if more than two different wing lengths exists.'''
+
'''(H9.22) Place near Part Section at Rail Post. '''
:Use a minimum lap of 2'-0" between K9 and K10 or K13 bars.  
+
:See slab sheet for rail post spacing.
  
'''(H10.21) Place under the K1-K2 Bar Permissible Alternate Shape Detail. '''
+
'''(H9.23)'''
:The K1 and K2 bar combination may be furnished as one bar as shown, at the contractor's option.  
+
:See Missouri Standard Plan 606.00 for details not shown.
  
==== H10b. Slip Form Option ====
+
'''(H9.24) Place near detail of bent bolt used for new bridges except double tees. '''
 +
:Bolt shall not be bent in slab depths greater than 14 inches, use 12 inches straight embedment.  
  
'''Optional slip form barrier curb details shall be placed on all jobs (except P/S Double-tee Structures) where applicable.'''
+
'''(H9.25) Place near details of shim plates used for horizontal alignment of State System 3. '''
 +
:Shim plates 6 x 3 x 1/16-inch may be used between the W6x20 post and 1/2-inch bent plate connection as required for horizontal alignment.
  
'''Use the following notes with the slip form option, including H10.1, H10.2, H10.3, H10.4, H10.5 or H10.6 or H10.7, and H10.7.1.'''
+
'''(H9.26) Place in General Notes and near details of shim plates used for horizontal alignment.'''  
 +
:Shim plates shall be galvanized after fabrication.
  
'''Add #5 crisscross bars for slip-form option. Base the length of these bars on the shortest distance between joints and use typically on each side of joints throughout structure.'''
+
'''(H9.27) Place near details of shim plates used for horizontal alignment of State System 4. '''
 +
:Shim plates 6 x 6 x 1/16-inch may be used between the W6x20 post and 6 x 6 x 3/8-inch plate. Shim plates 6 x 3 1/2 x 1/16-inch may be used between the W6x20 post and 1/2-inch bent plate connection as required for horizontal alignment.
  
'''(H10.81) Use underline portion for median barriers. '''
+
'''(H9.28) Place near detail specifying bar support at bent plates. '''
:Joint sealant and backer rods shall be used on all slip-form barrier curbs instead of joint filler and shall be in accordance with Sec 717 for silicone joint sealant for saw cut and formed joints <u>(except at end of slab of the end bents)</u>.
+
:Bar supports shall be Beam Bolsters (BB-ref. CRSI) and shall be galvanized. See Sec 706.
  
'''(H10.82)'''
 
:Plastic waterstop shall not be used with slip-form option.
 
  
'''(H10.83)'''
+
'''Remaining notes are only for temporary bridges except for Note H9.32 which is also used for rehabilitation of existing bridges and Note H9.34 which is used for all bridge types.'''
:For slip-form option, all sides of the <u>safety</u> <u>median</u> barrier curb <u>(Type C)</u> <u>(Type D)</u> shall have a vertically broomed finish and the curb top shall have a transversely broomed finish.
 
  
'''(H10.84)'''
+
'''(H9.31)'''
:C bars (slip-form option only) shall be used in addition to cast-in-place conventional forming reinforcement for bridge <u>safety</u> <u>median</u> barrier curb <u>(Type C)</u> <u>(Type D)</u>.
+
:If Type A guardrail is not attached to ends of the temporary structure, flared ends shall be required.  The existing thrie beam rails shall be modified to accept flared ends. Cost for furnishing and installing flared ends will be considered completely covered by the contract unit price for other items.
  
'''(H10.85)'''
+
'''(H9.32)'''
:Cost of silicone joint sealant and backer rod, complete in place, will be considered completely covered by the contract unit price for <u>Safety</u> <u>Median</u> Barrier Curb <u>(Type C)</u> <u>(Type D)</u>.
+
:Contractor shall verify all dimensions in field before ordering materials.
  
==== H10c. Temporary ====
+
'''(H9.33) Place near Part Section at Rail Post. '''
 +
:See preceding sheet for rail post spacing.
  
'''(H10.90)'''
+
'''(H9.34) Place in General Notes or near Elevation of Thrie Beam Rail. '''
:Method of attachment for the Type F temporary barrier shall be <u>the tie-down strap</u> <u>bolt through deck</u>.
+
:At bridge ends for head to head traffic, guardrail shall be used at all four corners and for single directional traffic, guardrail shall be used at entrance ends only unless required at the exit.
  
'''(H10.91)'''
+
'''(H9.35) Place near any detail specifying the bottom plate of the rail posts. '''
:Temporary barrier shall not be attached to the bridge.
+
:Bottom plate shall be fabricated from ASTM A709 Grade 50W steel and welded to two 5" floor bars.  Bottom plate shall not be galvanized.
  
=== H11. Miscellaneous ===
+
'''(H9.36) Place near any detail specifying both the bottom and base plate of the rail posts. '''
 +
:The size of the base and bottom plate may be increased depending on which grid option is used.
  
'''Construction Joint'''
+
'''(H9.37) Place near any detail specifying the welding of post to base plate of the rail posts. '''
 +
:Optional welding of the post to the base plate, in lieu of the weld shown, is a 5/16" fillet weld all around, including the edges of the post flanges.
  
'''(H11.1)'''
+
'''(H9.38) Place near any detail specifying the semi-circular notches of the rail posts.  '''
:Finish each side of joint with a 1/4 inch radius edging tool.
+
:Semi-circular notches centered on the axis of the post web ends may be made to facilitate galvanizing.
  
 +
:Guardrail delineators shall be attached to the top of the bridge guardrail and shall similarly use the delineator details of Missouri Standard Plan 617.10, except that the delineator body shall be attached to the top of the cap rail using galvanized anchorage as shown on  Missouri Standard Plan 606.00.  <u>Delineators on bridges with two-lane, two-way traffic shall have retroreflective sheeting on both sides.</u>  Cost of supplying and installing new delineators will be considered completely covered by other pay items.  Delineators shall be stored with bridge guardrail after use.
  
'''Pin and Flat Hexagonal Nut'''
+
=== H10. Barriers – Type A, B, C, D and H===
  
'''(H11.2)'''
+
==== H10a. Cast-In-Place Permanent Barrier====
:{|cellpadding="0"
 
|Material:||Pin = ASTM A668 (Class F)
 
|-
 
|&nbsp;||Nut = ASTM A709 Grade 36
 
|}
 
  
 +
'''The following notes shall be placed in the General Notes on the elevation sheet.'''
  
'''Plastic Waterstop (Use in the Curb and Parapet filled joints as specified in [[751.12_Protective_Barricades#751.12.2.8_Plastic_Waterstop|EPG 751.12.2.8 Plastic Waterstop]])'''
+
'''(H10.0.1) Use note if slip forming is allowed. Add asterisk to all C-bar leader notes and the one fiberglass bar leader note in the elevation of barrier. '''
 +
:'''*''' Slip-formed option only.
  
'''(H11.3)'''
+
'''(H10.0.2) Both methods may be used unless otherwise specified on Bridge Memorandum.'''  
:Plastic waterstop shall be placed in all <u>safety</u> barrier curb <u>(Type D)</u> filled joints, except structures with superelevation, use on all lower barrier curb joints only.
+
:Conventional forming <u>or slip</u> forming <u>may</u> <u>shall</u> be used. Saw cut joints may be used with conventional forming.
  
'''(H11.4)'''
+
'''(H10.1) Exclude underlined part for single span bridges. '''
:Cost of plastic waterstop, complete in place, will be considered completely covered by the contract unit price for <u>Safety</u>  <u>Barrier Curb</u> <u>(Type D)</u>.
+
:Top of barrier shall be built parallel to grade <u>with barrier joints (except at end bents) normal to grade</u>.
  
 +
'''(H10.2)'''
 +
:All exposed edges of barrier shall have either a 1/2-inch radius or a 3/8-inch bevel, unless otherwise noted.
  
'''Sign Supports'''
+
'''(H10.3)'''
 +
:Payment for all concrete and reinforcement, complete in place, will be considered completely covered by the contract unit price for Type <u>A</u> <u>B</u> <u>C</u> <u>D</u> <u>H</u> Barrier per linear foot.
  
'''(H11.5)'''
+
'''(H10.4)'''
:Payment for furnishing and placing anchor bolts for sign supports will be considered completely covered by the contract unit price for other items.
+
:Concrete in barrier shall be Class B-1.
  
'''(H11.6)'''
+
'''(H10.5) Use for Type B, D or H barrier. Include “left” or ”right” and exclude “for each structure” when barriers on each side of the bridge are not the same type. '''
:Payment for furnishing and erecting approximately <u>&nbsp;&nbsp;&nbsp;</u> pounds of steel for sign supports will be considered completely covered by the contract lump sum price for Fabricated Sign Support Brackets.
+
:Measurement of barrier is to the nearest linear foot <u>for each structure</u>, measured along the <u>left</u> <u>right</u> outside top of slab from end of <u>wing to end of wing</u> <u>slab to end of slab</u>.
  
 +
'''(H10.7) Use for Type A or C barriers.'''
 +
:Measurement of barrier is to the nearest linear foot, measured along the top of slab at centerline median from end of bridge approach slab to end of bridge approach slab.
 +
<div id="(H10.7.1) Notes shall be used on all barrier curbs"></div>
 +
'''(H10.7.1) Use for all barriers (see [[620.5 Delineators (MUTCD Chapter 3F)#620.5.6 Barrier Wall Delineation|Barrier Wall Delineation]]).'''
  
'''Plan of Slab: All Structures'''
+
:Concrete traffic barrier delineators shall be placed on top of the barrier as shown on Missouri Standard Plans 617.10 and in accordance with Sec 617. <u>Delineators on bridges with two-lane, two-way traffic shall have retroreflective sheeting on both sides.</u> Concrete traffic barrier delineators will be considered completely covered by the contract unit price for Type <u>A</u> <u>B</u> <u>C</u> <u>D</u> <u>H</u> Barrier.
 
 
'''(H11.8)'''
 
:Longitudinal slab dimensions are measured horizontally.
 
  
 +
{|style="padding: 0.3em; margin-left:10px; border:1px solid #a9a9a9; text-align:left; font-size: 95%; background:#f5f5f5" width="760px" align="center"
 +
|-
 +
|Below is additional guidance for using Note H10.7.1:
 +
|-
 +
|Bridges with two-lane, two-way traffic shall have retroreflective sheeting on both sides of the delineators. For two-lane, one-way traffic, retroreflective sheeting may be on one side only unless crossroad or entranceway traffic is just beyond exit to bridge and wrong way driving is to be discouraged with retroreflective sheeting on both sides of the delineators, (white and red in this case). "Delineators on bridges with two-lane, two-way traffic shall have retroreflective sheeting on both sides" may be modified, as required. For Type A and C barriers, retroreflective sheeting should be used on both sides of the delineators where there is not more than four lanes divided.
 +
|-
 +
|On bridges with more than two lanes, retroreflective sheeting is not required on both sides of the delineators.  The perception of a narrowing roadway at the bridge is of lesser consequence in terms of requiring guidance devices and does not warrant retroreflective sheeting on both sides of the delineators. "Delineators on bridges with two-lane, two-way traffic shall have retroreflective sheeting on both sides" may be removed at the discretion of the design team.
 +
|}
  
'''Pedestrian Guard Fence (Chain Link Type): General Notes'''
+
'''(H10.7.2) '''
 +
:Joint sealant and backer rods shall be in accordance with Sec 717 for silicone joint sealant for saw cut and formed joints.
  
'''(H11.10)'''
+
'''(H10.7.3) Use note if slip forming is allowed.'''
:Pedestrian guard fence (Chain link type) shall be in accordance with Sec 1043 except all fabric shall have the top and bottom edges knuckled.
+
:For slip-formed option, both sides of barrier shall have a vertically broomed finish and the top shall have a transversely broomed finish.
  
'''(H11.11)'''
+
'''(H10.7.4) Use for all grade separations except over railroads and county roads.'''
:All posts shall be vertical. Grout of 1/2" minimum thickness shall be placed under floor plates to provide for vertical alignment of posts.
+
:Plastic waterstop shall not be used with saw cut joints.
  
'''(H11.12)'''
 
:Payment for furnishing, galvanizing and erecting the fence and frame complete with anchor bolts and washers will be considered completely covered by the contract unit price for (72 in.) Pedestrian Fence (Structures) per linear foot.
 
  
'''(H11.13)'''
+
'''The following three notes shall be placed under section thru barrier.'''  
:Dimensions of pedestrian guard fence are measured horizontally.
 
  
'''(H11.14)'''
+
'''(H10.8)'''
:The maximum spacing allowed between pull post and end posts is 100 ft. Post brace and 1/2" Ø truss rod are required for panels adjacent to pull post and end posts only.
+
:Use a minimum lap of 3'-1" for #5 horizontal barrier bars.
  
'''(H11.15)'''
+
'''(H10.9) Areas shown are for standard barrier heights and a two percent cross slope.  '''
:Connect the lower end of the 1/2" Ø truss rod to the bottom of the pull posts and end posts to which the stretcher bar is attached.
+
:The cross-sectional area above the slab is <u>*</u> square feet.
  
'''(H11.16)'''
+
:{|
:(112 in.) Curved Top Pedestrian Fence (Structures) will be measured to the nearest linear foot for each structure measured along the bottom outside edge of the <u>sidewalk</u> <u>curb</u> from <u>&nbsp;&nbsp;&nbsp;&nbsp;</u> to <u>&nbsp;&nbsp;&nbsp;&nbsp;</u>.
+
|*||2.98 for a Type A barrier.
 +
|-
 +
| ||2.27 for a Type B barrier.
 +
|-
 +
| ||4.69 for a Type C barrier.  
 +
|-
 +
| ||3.52 for a Type D barrier.
 +
|-
 +
| ||3.59 for a Type D barrier used as a median.
 +
|-
 +
| ||2.89 for a Type H barrier
 +
|}
  
'''(H11.17)'''
+
'''(H10.9.1) Add (2) to the dimension for the top of slab to top of the R2 bar. '''
:Core wire size for wire fabric shall be 6 gage minimum.
+
:(2) To top of bar
  
  
'''Sidewalks'''
+
'''The following three notes shall be used for double-tee structures. '''
  
'''(H11.20)'''
+
'''(H10.10)'''
:All exposed edges of sidewalk shall have either a 1/2" radius or a 3/8" bevel, unless otherwise noted.  
+
:Coil inserts shall have a concrete ultimate pullout strength of not less than 36,000 pounds in 5000 psi concrete and an ultimate tensile strength of not less than 36,000 pounds.
  
'''(H11.21)'''
+
'''(H10.11)'''
:Payment for all concrete and reinforcement, complete in place, will be considered completely covered by the contract unit price for Sidewalk (Bridges) per sq. foot.
+
:Threaded coil rods shall have an ultimate capacity of 36,000 pounds. All coil inserts and threaded coil rods shall be galvanized in accordance with AASHTO M 232 (ASTM A153), Class C.  
  
'''(H11.22)'''
+
'''(H10.12)'''
:Concrete in the sidewalk shall be Class B-2.
+
:Payment for furnishing and installing coil inserts and threaded coil rods will be considered completely covered by the contract unit price for Type <u>A</u> <u>B</u> <u>C</u> <u>D</u> <u>H</u> Barrier.
  
'''(H11.23)'''
 
:Measurement of the sidewalk is to the nearest square foot for each structure, measured horizontally from the outside face of safety barrier curb to the outside edge of sidewalk and from end of slab to end of slab.
 
  
== I. Revised Structures Notes ==
+
'''The following two notes, when appropriate, shall be placed under the title of the elevation of barrier. '''
  
 +
'''(H10.12.1) Dimensions shall be horizontal unless otherwise specified on Bridge Memorandum. '''
 +
:Longitudinal dimensions are <u>horizontal</u> <u>arc dimensions</u>.
  
=== I1. General ===
+
'''(H10.12.2)'''
 +
:Longitudinal dimensions are along top of <u>barrier</u> <u>outside edge of slab</u> parallel to grade.
  
'''(I1.1)'''
+
'''The following two notes shall be placed under the permissible alternate bar shape detail. '''
:Outline of old work is indicated by light dashed lines.  Heavy lines indicate new work.
 
  
'''(I1.2)'''
+
'''(H10.13) Use R2 for Type D or H barriers, R3 for Type B barrier and M2 for two separate Type D barriers used as a median. Add (4) to the combined #5 bar leader note. Exclude note and associated detail for CIP slabs. '''
:Contractor shall verify all dimensions in field before ordering new material.
+
:(4) The <u>R2</u> <u>R3</u> <u>M2</u> bar and #5 bottom transverse slab bar in cantilever (prestressed panels only) combination may be furnished as one bar as shown, at the contractor's option.
  
'''(I1.3)'''
+
'''(H10.14) Use R1 for Type B, D or H barriers. Use M1 for two separate Type D barriers used as a median. Add (3) to the two separated #5 bar leader notes. '''
:Bars bonded in old concrete not removed shall be cleanly stripped and embedded into new concrete where possible.  If length is available, old bars shall extend into new concrete at least 40 diameters for plain bars and 30 diameters for deformed bars, unless otherwise noted.
+
:(3) The <u>R1</u> <u>M1</u> bar may be separated into two bars as shown, at the contractor's option, only when slip forming is not used. (All dimensions are out to out.)
  
 +
'''(H10.15) Use note if slip forming is allowed. Place under the part elevation of barrier and add (1) to fiberglass bar leader notes in the section thru saw cut joint and part elevation of barrier. '''
 +
:(1) Four feet long, centered on joint, slip-formed option only
  
'''Use the following notes where a broken concrete surface has no new concrete against it. Use bituminous paint below ground line and qualified special mortar above ground line.'''
+
<div id="Place general notes H10.19,"></div>
 +
'''Place general notes H10.19, H10.20 and H10.7.1 on the barrier at end bents sheet with notes H10.19 and H10.20 under the Reinforcing Steel heading. '''
  
'''(I1.4)'''
+
'''(H10.19)'''
:The area exposed by the removal of concrete and not covered with new concrete shall be coated with an approved <u>bituminous paint</u> <u>qualified special mortar in accordance with Sec 704</u>.
 
  
'''(I1.5) Use with joint filler joints with Asphaltic Concrete Wearing Surface.'''
+
:Minimum clearance to reinforcing steel shall be 1 1/2" except as shown for bars embedded into end bent.  
:Joint shall be cleaned per the manufacturers recommendations. Cost of Concrete and Asphalt Joint Sealer and Backer Rod will be considered completely covered by contract unit price per other items included in the contract.
 
  
 +
'''(H10.20) Use for Type B barrier only. Use 2’-7” and K10 bars for barrier ending on wing walls adding K13 bars with two different wing lengths. Will need to add more bars if more than two different wing lengths exist. Use 3’-1” and R6 bars for barrier ending on bridge deck. '''
 +
:Use a minimum lap of <u>2'-7"</u> <u>3’-1”</u> between K9 and <u>K10 or K13</u> <u>R6</u> bars.
  
'''Concrete Slab with Overlay'''
+
'''(H10.21) Place note under the K Bar Permissible Alternate Shape detail on the barrier at end bents sheet. Use K1 and K2 for Type B barrier; K9 and K10 for Type D barrier; K3 and K5 for Type H barrier. '''
 +
:The <u>K1 and K2</u> <u>K9 and K10</u> <u>K3 and K5</u> bar combination may be furnished as one bar as shown, at the contractor's option.
  
'''(I1.10)  Use note for all wearing surfaces except epoxy polymer concrete overlay.'''
+
==== H10b. Precast Temporary Barrier====
:In order to maintain grade and a minimum thickness of overlay as shown on plans it may be necessary to use additional quantities of overlay at various locations throughout the structure.  The cost of furnishing and installing the overlay will be considered completely covered in the contract unit price, including all additional labor, materials or equipment for variations in thickness of overlay.
 
  
'''(l1.11) Use note for only epoxy polymer concrete overlay.'''
+
'''(H10.90)'''
:The contractor shall exercise care to ensure spillage over joint edges is prevented and that a neat line is obtained along any terminating edge of the epoxy polymer concrete.
+
:Method of attachment for temporary barrier shall be <u>tie-down strap</u> <u>bolt through deck</u>.
  
'''(l1.12) Use note only with preventive maintenance jobs.'''
+
'''(H10.91)'''
:Concrete for repairing concrete deck shall be a qualified special mortar in accordance with Sec 704 instead of the Class B-2 or B-1 concrete.
+
:Temporary barrier shall not be attached to the bridge.
  
'''(I1.13) <font color="purple">[MS Cell]</font color="purple"> Use the following table and notes with alternate concrete wearing surfaces.'''
+
=== H11. Miscellaneous ===
:{|border="0" style="text-align:center;" cellpadding="5" cellspacing="0"
 
|-
 
!colspan="2" style="border-top:3px solid black; border-bottom:1px solid black; border-left:3px solid black; border-right:3px solid black"|Alternate Concrete Wearing Surface
 
|-
 
!style="border-top:1px solid black; border-bottom:1px solid black; border-left:3px solid black; border-right:1px solid black"|Type of Concrete Wearing Surface
 
!style="border-top:1px solid black; border-bottom:1px solid black; border-left:1px solid black; border-right:3px solid black"|Type Used<br/>(<math>\sqrt{}</math>)
 
|-
 
|align="left" style="border-top:1px solid black; border-bottom:1px solid gray; border-left:3px solid black; border-right:1px solid black;"|Low Slump Concrete Wearing Surface
 
|style="border-top:1px solid black; border-bottom:1px solid gray; border-left:1px solid black; border-right:3px solid black"|&nbsp;
 
|-
 
|align="left" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:3px solid black; border-right:1px solid black;"|Silica Fume Concrete Wearing Surface
 
|style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:3px solid black"|&nbsp;
 
|-
 
|align="left" style="border-top:1px solid gray; border-bottom:3px solid black; border-left:3px solid black; border-right:1px solid black;"|&nbsp;
 
|style="border-top:1px solid gray; border-bottom:3px solid black; border-left:1px solid black; border-right:3px solid black"|&nbsp;
 
|-
 
|align="left" colspan="2"|MoDOT construction personnel shall complete column labeled "Type Used (<math>\sqrt{}</math>)".
 
|-
 
|align="left" colspan="2"|The contractor shall select one of the alternate concrete wearing surfaces<br/>listed in the table.  The alternate concrete wearing surface method of<br/>measurement and basis of payment shall be in accordance with Sec 505.
 
|}
 
  
 +
'''Construction Joint'''
  
'''Removal and Storage of Existing Bridge Rails'''
+
'''(H11.1)'''
 +
:Finish each side of joint with a 1/4 inch radius edging tool.
  
'''(I1.20)'''
 
:The existing bridge rails <u>and posts</u> shall be stored at a location as designated by the engineer on the MoDOT Maintenance Lot at <u>&nbsp;&nbsp;&nbsp;&nbsp;</u>.
 
  
 +
'''Pin and Flat Hexagonal Nut'''
  
'''Extension of Box Culverts'''
+
'''(H11.2)'''
 +
:{|cellpadding="0"
 +
|Material:||Pin = ASTM A668 (Class F)
 +
|-
 +
|&nbsp;||Nut = ASTM A709 Grade 36
 +
|}
  
'''(I1.41)'''
 
:Bottom of top slab, top of bottom slab, and inside faces of walls shall be built flush with the old structure.
 
  
'''(I1.42)'''
+
'''Plastic Waterstop (Use in the barrier joints and parapet joints as specified in [[751.12_Protective_Barricades#751.12.1.2.3 Plastic Waterstops|EPG 751.12.1.2.3 Plastic Waterstops]])'''
:Bottom of new slab shall be built flush with the bottom of slab of the old box and the height of walls varied as necessary to extend the walls into rock as specified.
 
  
 +
'''(H11.3)'''
 +
:Plastic waterstop shall be placed in all formed joints, except structures with superelevation, use on lower joints only.
  
'''Making End Bents Integral'''
+
'''(H11.4)'''
 +
:Cost of plastic waterstop, complete in place, will be considered completely covered by the contract unit price for Type <u>A</u> <u>B</u> <u>C</u> <u>D</u> <u>H</u> Barrier.
  
'''(I1.51)'''
+
'''Sign Supports'''
:The exposed and accessible surfaces of the existing structural steel and bearings that will be encased in concrete shall be cleaned with a minimum of SSPC-SP-2 surface preparation before concrete is poured.  Payment for cleaning steel to be encased in concrete will be considered completely covered by the contract unit price for <u>Class B-2 Concrete</u> <u>Slab on Steel</u>.
 
  
'''(I1.52)'''
+
'''(H11.5)'''
:The ___ bars are segmented for ease of placement through girder web holes. The total bar length for ___ bars shown in Bill of Reinforcing Steel allows for one lap splice with a length of ___. Actual bar segment lengths to be determined by contractor for ease of installing bars. The contractor may use a mechanical bar splice in lieu of a lap splice. When a mechanical bar splice is used, the actual bar segment length will be determined by the contractor to accommodate manufacturer's recommendations for installation and ease of construction. The cost of furnishing and installing the bar splices will be considered completely covered by the contract unit price for Reinforcing Steel. No adjustment of the quantity of reinforcing steel will be allowed for the use of mechanical bar splices.
+
:Payment for furnishing and placing anchor bolts for sign supports will be considered completely covered by the contract unit price for other items.
  
'''(I1.53)'''
+
'''(H11.6)'''
:Cost of field drilling holes in existing <u>plate girder</u> <u>wide flange beam</u> webs will be considered completely covered by the contract unit price for <u>Class B-2 Concrete</u> <u>Slab on Steel</u>.
+
:Payment for furnishing and erecting approximately <u>&nbsp;&nbsp;&nbsp;</u> pounds of steel for sign supports will be considered completely covered by the contract lump sum price for Fabricated Sign Support Brackets.
  
'''Curb Block-Out'''
 
  
'''(I1.60)'''
+
'''Plan of Slab: All Structures'''
:7/8"&oslash; Threaded Rods with nuts and washers shall be used in place of 7/8"&oslash; Bolts (ASTM A307).
 
  
'''(I1.61)'''
+
'''(H11.8)'''
:1"&oslash; holes shall be drilled through existing end post for placement of 7/8"&oslash; threaded rods, nuts, and washers.
+
:Longitudinal slab dimensions are measured horizontally.
  
  
'''Widening'''
+
'''Pedestrian Guard Fence (Chain Link Type): General Notes'''
  
'''(I1.62)'''
+
'''(H11.10)'''
:Dimensions:
+
:Pedestrian guard fence (Chain link type) shall be in accordance with Sec 1043 except all fabric shall have the top and bottom edges knuckled.
:&nbsp; &nbsp; &nbsp; Longitudinal dimensions are based on the original design plans.
 
  
'''(I1.64''')
+
'''(H11.11)'''
:Stringer Support:
+
:All posts shall be vertical. Grout of 1/2" minimum thickness shall be placed under floor plates to provide for vertical alignment of posts.
:&nbsp; &nbsp; &nbsp; All existing stringers in the span being strengthened shall be raised simultaneously <math>\, *</math> at jacking point and supported during welding of new steel plates.
 
  
'''(I1.65)'''
+
'''(H11.12)'''
:The temporary supports must be capable of safely supporting a service load of approximately <math>\, **</math> tons per stringer (factor of safety not included) (see Special Provisions).
+
:Payment for furnishing, galvanizing and erecting the fence and frame complete with anchor bolts and washers will be considered completely covered by the contract unit price for (72 in.) Pedestrian Fence (Structures) per linear foot.
  
'''(I1.66)'''
+
'''(H11.13)'''
:<math>\, *</math> Scarification not required for Asphaltic Concrete Wearing Surface and Epoxy Polymer Concrete Overlay.
+
:Dimensions of pedestrian guard fence are measured horizontally.
  
<div id="(I1.67) Field Welding New Stiffeners"></div>
+
'''(H11.14)'''
 +
:The maximum spacing allowed between pull post and end posts is 100 ft. Post brace and 1/2" Ø truss rod are required for panels adjacent to pull post and end posts only.
  
'''(I1.67) Field Welding New Stiffeners or New Connection Plates or Cover Plates to Existing Steel'''
+
'''(H11.15)'''
+
:Connect the lower end of the 1/2" Ø truss rod to the bottom of the pull posts and end posts to which the stretcher bar is attached.
:Field welded fillet  welds  shall be NDT by the magnetic particle process as required by AASHTO/AWS D1.5 2002, Bridge Welding Code clause 6.7.2.
 
  
<div id="Rock Blanket"></div>
+
'''(H11.16)'''
 +
:(112 in.) Curved Top Pedestrian Fence (Structures) will be measured to the nearest linear foot for each structure measured along the bottom outside edge of the <u>sidewalk</u> <u>curb</u> from <u>&nbsp;&nbsp;&nbsp;&nbsp;</u> to <u>&nbsp;&nbsp;&nbsp;&nbsp;</u>.
  
'''Rock Blanket'''
+
'''(H11.17)'''
+
:Core wire size for wire fabric shall be 6 gage minimum.
'''(I1.70) Use note for redecks or in other cases where the rock blanket elevations are not shown on the bridge plans and the top of the rock blanket is required to be flush to the existing ground line in accordance with the Memorandum of Agreement with SEMA.'''
+
<div id="(H11.19)"></div>
 +
'''(H11.19)'''  Use for ornamental pedestrian fencing.
 +
:The design live load for pedestrian railings shall be in accordance with AASHTO LRFD Bridge Design Specifications except that a uniform load of 50 lb/ft and a concentrated load of 200 lb need not be applied simultaneously.  The posts of pedestrian fencing will require both loadings applied simultaneously.
  
:The top of rock blanket shall be flush to the ground line as directed by the engineer. (Roadway Item)
 
  
=== I2. Resin & Cone Anchors ===
+
'''Sidewalks'''
  
'''Use Resin Anchors unless concrete depths are insufficient.'''
+
'''(H11.20)'''
 +
:All exposed edges of sidewalk shall have either a 1/2" radius or a 3/8" bevel, unless otherwise noted.
  
'''(I2.1)'''
+
'''(H11.21)'''
:The contractor shall use one of the qualified resin anchor systems in accordance with Sec 1039.
+
:Payment for all concrete and reinforcement, complete in place, will be considered completely covered by the contract unit price for Sidewalk (Bridges) per sq. foot.
  
'''(I2.2) * Pay item in which resin anchor system is embedded.'''
+
'''(H11.22)'''
:Cost of furnishing and installing the resin anchor systems, complete in place, will be considered completely covered by the contract unit price for <u>*</u>.
+
:Concrete in the sidewalk shall be Class B-2.
  
'''(I2.3)'''
+
'''(H11.23)'''
:The minimum embedment depth in concrete with f'<sub>c</sub> = 4,000 psi for the resin anchor systems shall be that required to meet the minimum ultimate pullout strength in accordance with Sec 1039 but shall not be less than 5".
+
:Measurement of the sidewalk is to the nearest square foot for each structure, measured horizontally from the outside face of barrier to the outside edge of sidewalk and from end of slab to end of slab.
  
'''Note to designer:'''<br/>A minimum factor of safety of 2 should be used when determining the number of anchors to be used.
+
== I. Revised Structures Notes ==
  
'''(I2.4)(Use when reinforcing steel is substituted for the threaded rod stud.)'''
 
:<u>A</u> <u>An epoxy coated</u> #<u>****</u> Grade 60 reinforcing bar <u>*****</u> long shall be substituted for the <u>******</u.>&oslash; threaded rod.
 
  
{|
+
=== I1. General ===
|****||Bar size.
 
|-
 
|*****||Length of bar required by design.
 
|-
 
|******||Diameter of threaded rod.
 
|}
 
  
 +
'''(I1.0.1) Use “slab surface” for deck replacements. '''
 +
:Roadway surfacing adjacent to bridge ends shall match new bridge <u>slab surface</u> <u>wearing surface</u> (roadway item).
  
'''Cone Expansion Anchors'''
+
'''(I1.0.2) '''
 +
:All concrete repairs shall be in accordance with Sec 704, unless otherwise noted.
  
'''(I2.30) ***  Pay item in which cone expansion anchor is embedded.'''
+
'''(I1.0.3) Use note when required for rush jobs.'''
:Cost of furnishing and installing cone expanson anchor will be considered completely covered by the contract unit price for <u>***</u>.
+
:Qualified special mortar in accordance with job special provisions may be used for half-sole repair <u>and deck repair with void tube replacement</u>.
  
'''(I2.31)'''
+
'''(I1.1)'''
:The <u>*</u>" diameter cone expansion anchors shall have a minimum ultimate pullout strength of <u>**</u> lbs. in concrete with f'<sub>c</sub> = 4,000 psi.
+
:Outline of existing work is indicated by light dashed lines. Heavy lines indicate new work.
  
{|style="text-align:center;"
+
'''(I1.2)'''
|-
+
:Contractor shall verify all dimensions in field before ordering new material.
|width="100pt"|* DIAMETER||width="100pt"|** PULLOUT
 
|-
 
|3/8"||3,900
 
|-
 
|1/2"||7,500
 
|-
 
|5/8"||10,800
 
|-
 
|3/4"||12,000
 
|}
 
  
=== I3. Special Repair Zones ===
+
'''(I1.3)'''
 +
:Bars bonded in existing concrete not removed shall be cleanly stripped and embedded into new concrete where possible.  If length is available, existing bars shall extend into new concrete at least 40 diameters for plain bars and 30 diameters for deformed bars, unless otherwise noted.
  
'''(I3.1)'''
 
:Any half-soling required in the areas designated as special repair zones shall be completed in alphabetical sequence.  Any repair in the remainder of the bridge that is adjacent to Zone A and not designated as a special repair zone shall be completed prior to work in Zone A.
 
  
'''(I3.2)'''
+
'''Use Notes I1.4 and I1.5 where a broken concrete surface has no new concrete against itUse bituminous paint below ground line and qualified special mortar above ground line.'''
:Removal and repair shall be completed in one special repair zone and concrete shall have attained a compressive strength of 3200 psi before work can be started in the next special repair zoneBefore placing concrete in areas adjacent to areas of subsequent repair, the concrete shall be separated with a material such as polyethylene sheets to aid in removal of old concrete.
 
  
'''(I3.5) Use for structures with multiple column bents.'''
+
'''(I1.4)'''
:Zones with the same letter designation may be repaired at the same time.
+
:The area exposed by the removal of concrete and not covered with new concrete shall be coated with an approved <u>bituminous paint</u> <u>qualified special mortar in accordance with Sec 704</u>.
  
'''(I3.6) Use for structures with single column bents.'''
+
'''(I1.5) Use with joint filler joints with Asphaltic Concrete Wearing Surface.'''
:Zones with the same letter designation may be repaired at the same time except for the zones directly adjacent to the centerline of bent. If either of the zones adjacent to centerline of bent has a single repair area of over 10 square feet or a total repair area of over 20 square feet, that zone shall be repaired before removing concrete in the other zone of the same designation at that bent.
+
:Joint shall be cleaned per the manufacturer's recommendations. Cost of Concrete and Asphalt Joint Sealer and Backer Rod will be considered completely covered by contract unit price per other items included in the contract.
  
'''(I3.10) Use for voided or solid slab structures.'''
+
'''(I1.6) Use as an asterisk note when tinting is specified on Bridge Memorandum adding corresponding asterisk to slab edge repair and superstructure repair (unformed) leader notes.'''
:If any single repair area does not exceed 4 square feet in size and the total repair within a special repair zone does not exceed 12 square feet, the special repair zone requirement does not apply for that zone. Any damage sustained to the void tube as a result of the contractor's operations shall be patched or replaced as required by the engineer at the contractor's expense.  
+
:Match existing concrete color. Apply tinted sealer to blend repair to existing concrete.
  
'''(I3.11)  Use for voided slab structures.'''
 
:An exposed void in the deck shall be patched as approved by the engineer in a manner that shall maintain the void area completely free of concrete.  Cost of patching an exposed void will be considered completely covered by the contract unit price for Repairing Concrete Deck (Half-Soling).
 
  
'''(I3.12)  Use for voided slab structures.'''
+
'''Concrete Slab with Wearing Surface'''
:When a deteriorated portion of the void tube is beyond the point of patching as determined by the engineer, the portion of the deteriorated void tube shall be replaced. The void area shall be maintained completely free of concrete. Cutting of the  longitudinal reinforcing steel will not be permitted. The fiber tubes for producing the voids shall have an outside diameter with the wall thickness the same as the existing tubes and anchored at not more than the original spacing. Cost of replacing the void tube will be considered completely covered by the contract unit price for Deck Repair with Void Tube Replacement.
 
  
 +
'''(I1.10)  Use note for all wearing surfaces except epoxy polymer wearing surfaces.'''
 +
:In order to maintain grade and a minimum thickness of wearing surface as shown on plans it may be necessary to use additional quantities of wearing surface at various locations throughout the structure.  The cost of furnishing and installing the wearing surface will be considered completely covered in the contract unit price, including all additional labor, materials or equipment for variations in thickness of wearing surface.
  
'''Use following notes for box and deck girder structures.'''
+
'''(l1.11)  Use note for chip seals and polymer wearing surfaces.'''
 +
:The contractor shall exercise care to ensure spillage over joint edges is prevented and that a neat line is obtained along any terminating edge of the wearing surface.
  
'''(I3.16)'''
+
'''(l1.12) Use note only with preventive maintenance jobs.'''
:Total width of full depth repair shall not exceed 1/3 of the deck width at one time.  For any area of deck repair that extends over a concrete girder and is more than 18 inches in length along the girder, the concrete removal shall stop at the centerline of girder and repair completed in this area.  Prior to continuing work in this area, the concrete shall have attained a compressive strength of 3200 psi.  No traffic shall be permitted over the girder that is undergoing repair.
+
:Concrete for repairing concrete deck shall be a qualified special mortar in accordance with Sec 704 instead of the Class B-2 or B-1 concrete.
  
'''(I3.17)'''
+
'''(I1.13) <font color="purple">[MS Cell]</font color="purple"> Place following table and notes near the estimated quantities table on the design plans for optional concrete wearing surface and optional very early strength concrete wearing surface as specified on the Bridge Memorandum. '''
:When the full depth repair extends over a diaphragm or girder and the deteriorated concrete extends into the diaphragm or girder, all deteriorated concrete shall be removed and replaced as full depth repair. Concrete in girders shall not be removed below the deck haunch of the girder without prior review and approval from the engineer.
+
:{|border="0" style="text-align:center;" cellpadding="5" cellspacing="0"
 
+
|-
 
+
!colspan="2" style="border-top:3px solid black; border-bottom:1px solid black; border-left:3px solid black; border-right:3px solid black"|Optional <u>Very Early Strength</u> Concrete Wearing Surface
'''Use following notes for box girder structures.'''
+
|-
 
+
!style="border-top:1px solid black; border-bottom:1px solid black; border-left:3px solid black; border-right:1px solid black"|Type of Concrete Wearing Surface
'''(I3.20)'''
+
!style="border-top:1px solid black; border-bottom:1px solid black; border-left:1px solid black; border-right:3px solid black"|Type Used<br/>(√)
:Interior falsework installed by the contractor resting on the bottom slab shall be removed where entry access is available.
+
|-
 +
|align="left" style="border-top:1px solid black; border-bottom:1px solid gray; border-left:3px solid black; border-right:1px solid black;"|Low Slump Concrete Wearing Surface
 +
|style="border-top:1px solid black; border-bottom:1px solid gray; border-left:1px solid black; border-right:3px solid black"|&nbsp;
 +
|-
 +
|align="left" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:3px solid black; border-right:1px solid black;"|Latex Modified Concrete Wearing Surface
 +
|style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:3px solid black"|&nbsp;
 +
|-
 +
|align="left" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:3px solid black; border-right:1px solid black;"|Silica Fume Concrete Wearing Surface
 +
|style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:3px solid black"|&nbsp;
 +
|-
 +
|align="left" style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:3px solid black; border-right:1px solid black;"|Latex Modified Very Early Strength Concrete Wearing Surface
 +
|style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:3px solid black"|&nbsp;
 +
|-
 +
|align="left" style="border-top:1px solid gray; border-bottom:3px solid black; border-left:3px solid black; border-right:1px solid black;"|CSA Cement Very Early Strength Concrete Wearing Surface
 +
|style="border-top:1px solid gray; border-bottom:3px solid black; border-left:1px solid black; border-right:3px solid black"|&nbsp;
 +
|-
 +
|align="left" colspan="2"|MoDOT construction personnel shall complete column labeled "Type Used (√)".
 +
|-
 +
|align="left" colspan="2"|The contractor shall select one of the optional <u>very early strength</u> concrete wearing surfaces listed in<br/>the table. The optional <u>very early strength</u> concrete wearing surface method of measurement and<br/>basis of payment shall be in accordance with Sec 505.  
 +
|}
  
'''(I3.21)'''
 
:If any single repair area does not exceed 9 square feet in size and the total repair within a special repair zone does not exceed 27 square feet, the special repair zone requirement does not apply for that zone.  Half-soling repair in the special repair zone, on either side of the intermediate bents, shall be to a depth that will not expose half the diameter of the longitudinal reinforcing bar.  Full depth repair shall be made when removal of deteriorated concrete exposes half or more of the diameter of the longitudinal reinforcing bar.
 
  
== J. MSE Wall Notes (Notes for Bridge Standard Drawings)==
+
'''(I1.14) <font color="purple">[MS Cell]</font color="purple"> Place following table and notes near the estimated quantities table on the design plans for optional polymer wearing surface as specified on the Bridge Memorandum. '''
 +
:{|border="0" style="text-align:center;" cellpadding="5" cellspacing="0"
 +
|-
 +
!colspan="2" style="border-top:3px solid black; border-bottom:1px solid black; border-left:3px solid black; border-right:3px solid black"|Optional Polymer Wearing Surface
 +
|-
 +
!style="border-top:1px solid black; border-bottom:1px solid black; border-left:3px solid black; border-right:1px solid black"|Type of Polymer Wearing Surface
 +
!style="border-top:1px solid black; border-bottom:1px solid black; border-left:1px solid black; border-right:3px solid black"|Type Used<br/>(√)
 +
|-
 +
|align="left" style="border-top:1px solid black; border-bottom:1px solid gray; border-left:3px solid black; border-right:1px solid black;"|Epoxy Polymer Wearing Surface
 +
|style="border-top:1px solid black; border-bottom:1px solid gray; border-left:1px solid black; border-right:3px solid black"|&nbsp;
 +
|-
 +
|align="left" style="border-top:1px solid gray; border-bottom:3px solid black; border-left:3px solid black; border-right:1px solid black;"|MMA Polymer Slurry Wearing Surface
 +
|style="border-top:1px solid gray; border-bottom:3px solid black; border-left:1px solid black; border-right:3px solid black"|&nbsp;
 +
|-
 +
|align="left" colspan="2"|MoDOT construction personnel shall complete column labeled "Type Used (√)".
 +
|-
 +
|align="left" colspan="2"|The contractor shall select one of the optional polymer wearing surfaces listed in the<br/>table. The optional polymer wearing surface method of measurement and basis of<br/>payment shall be in accordance with Sec 623.
 +
|}
 +
 +
'''(I1.15) Use note when specified on Bridge Memorandum.'''
 +
:Broadcast aggregate for MMA polymer slurry wearing surface shall be a black beauty type aggregate.
  
 +
'''(l1.16) Use note when specified on Bridge Memorandum. Requires non-standard special provision [https://spexternal.modot.mo.gov/sites/de/JSP/NJSP1513.docx?d=we869653119d14e99945841e7d7f615c3 NJSP1513].'''
 +
:Broadcast aggregate for MMA polymer slurry wearing surface shall be a high friction (HFST) aggregate in accordance with special provisions.
  
=== J1. General ===
+
'''(l1.17) Use note when specified on Bridge Memorandum.'''
 +
:Reflective deck cracks shall be treated in accordance with Sec 623.  
  
'''(J1.1)'''
 
:Factor of safety shall be 2.0 for overturning and 1.5 for sliding.
 
  
'''(J1.2)'''
+
'''Removal and Storage of Existing Bridge Rails'''
:The cost of joint filler and joint seal, complete in place, will be considered completely covered by the contract unit price for Concrete Traffic Barrier (Type <u>A</u> <u>D</u>). See Roadway Plans.  
+
 
 +
'''(I1.20)'''
 +
:The existing bridge rails <u>and posts</u> shall be stored at a location as designated by the engineer on the MoDOT Maintenance Lot at <u>&nbsp;&nbsp;&nbsp;&nbsp;</u>.
  
'''(J1.3)'''
 
:For seismic design the factor of safety shall be 1.5 for overturning and 1.1 for sliding.
 
  
'''(J1.4)'''
+
'''Extension of Box Culverts'''
:&oslash;<sub>b</sub> = <u>&nbsp; &nbsp;</u>&deg; and Unit weight, Ɣ<sub>b</sub> = ___pcf for retained backfill material to be retained by the mechanically stabilized earth wall system.
 
  
'''(J1.5)'''
+
'''(I1.41)'''
:<u>&oslash;<sub>f</sub> = &nbsp; &nbsp;&deg; for unimproved foundation ground where wall is to rest.</u>
+
:Bottom of top slab, top of bottom slab, and inside faces of walls shall be built flush with the existing structure.
:<u>&oslash;<sub>f</sub> = &nbsp; &nbsp;&deg; for improved foundation ground where wall is to rest.</u>
 
  
'''(J1.6)'''
+
'''(I1.42)'''
:Actual &oslash; &ge; 34&deg; for the select granular backfill (reinforced backfill and wedge area backfill) for structural systems.
+
:Bottom of new slab shall be built flush with the bottom of slab of the existing box and the height of walls varied as necessary to extend the walls into rock as specified.
  
'''(J1.7)'''
+
<div id="Making End Bents Integral"></div>
:Design &oslash; = 34&deg; for the select granular backfill (reinforced backfill) only for structural systems.
+
'''Making End Bents Integral'''
  
'''(J1.8)'''
+
'''(I1.51)'''
:All concrete for leveling pad <u>and coping</u> shall be Class B or B-1 with f'<sub>c</sub> = 4000 psi.
+
:The exposed and accessible surfaces of the existing structural steel and bearings that will be encased in concrete shall be cleaned with a minimum of SSPC-SP-3 surface preparation and coated with a minimum of one coat of gray epoxy-mastic primer (non-aluminum) in accordance with Sec 1081 to produce a dry film thickness of not less than 3 mils before concrete is poured. The surface preparation and coating for girders shall extend a minimum of one foot outside the face of the girder encasement. Payment for cleaning and coating steel to be encased in concrete will be considered completely covered by the contract unit price for <u>Class B-2 Concrete</u> <u>Slab on Steel</u>.
  
'''(J1.10)'''
+
'''(I1.52)'''
:Panel reinforcement shall be epoxy coated.
+
:The ___ bars are segmented for ease of placement through girder web holes. The total bar length for ___ bars shown in Bill of Reinforcing Steel allows for one lap splice with a length of ___. Actual bar segment lengths to be determined by contractor for ease of installing bars. The contractor may use a mechanical bar splice in lieu of a lap splice. When a mechanical bar splice is used, the actual bar segment length will be determined by the contractor to accommodate manufacturer's recommendations for installation and ease of construction. The cost of furnishing and installing the bar splices will be considered completely covered by the contract unit price for Reinforcing Steel. No adjustment of the quantity of reinforcing steel will be allowed for the use of mechanical bar splices.
  
'''(J1.11)'''
+
'''(I1.53)'''
:Anchorage reinforcement shall be spaced to avoid roadway drop inlet behind wall.
+
:Cost of field drilling holes in existing <u>plate girder</u> <u>wide flange beam</u> webs will be considered completely covered by the contract unit price for <u>Class B-2 Concrete</u> <u>Slab on Steel</u>.
  
'''(J1.12)'''
+
'''Curb Block-Out'''
:A filter cloth meeting the requirements for a Separation Geotextile material shall be placed between the select granular backfill for structural systems and the backfill being retained by the mechanically stabilized earth wall system.
 
  
'''(J1.13)'''
+
'''(I1.60)'''
:Coping shall be required on this structure unless a small block system is used. Bond breaker (roofing felt or other approved alternate) between wall panel and coping required if coping is cast in place.
+
:7/8"&oslash; Threaded Rods with nuts and washers shall be used in place of 7/8"&oslash; Bolts (ASTM A307).
  
'''(J1.13a) '''
+
'''(I1.61)'''
:Wall contractor shall show the following items on the design drawings and/or on the fabricator shop drawings.
+
:1"&oslash; holes shall be drilled through existing end post for placement of 7/8"&oslash; threaded rods, nuts, and washers.
::1. Leveling pad horizontal.
 
::2. Leveling pad length and step elevations shall be based on wall manufacture’s recommendation. Top of leveling pad elevations shall not be higher than theoretical top of leveling pad elevations shown on these plans.
 
  
  
'''For Battered Small Block Walls'''
+
'''In "General Notes:" section of plans, place the following note under the heading "Miscellaneous:" when existing longitudinal dimensions are used.'''
  
'''(J1.14)'''
+
'''(I1.62)'''
:The top and bottom elevations are given for a vertical wall. If a battered small block wall system is used, the height of the wall shall be adjusted as necessary to fit the ground slope and the concrete leveling pad shall be adjusted as necessary to account for the wall batter. If a fence is built on an extended gutter, then the height of the wall shall be adjusted further.
+
:Longitudinal dimensions are based on the original design plans.
 +
 
 +
'''In "General Notes:" section of plans, place the following two notes under the heading "Beam Support:" when strengthening existing beams under traffic.'''
 +
 
 +
'''(I1.64''')
 +
:All existing beams in the span being strengthened shall be raised simultaneously Dimension H at jacking point and supported during welding of new steel plates.
 +
 
 +
'''(I1.65)'''
 +
:The temporary supports must be capable of safely supporting a service load of approximately Load J tons per beam (factor of safety not included). See special provisions.
 +
 
 +
'''(I1.66)'''
 +
:<math>\, *</math> Scarification not required for Asphaltic Concrete, MMA Polymer Slurry and Epoxy Polymer Wearing Surfaces.
 +
 
 +
<div id="(I1.67) Field Welding New Stiffeners"></div>
 +
 
 +
'''(I1.67) Field Welding New Stiffeners or New Connection Plates or Cover Plates to Existing Steel'''
 +
 +
:Field welded fillet  welds  shall be NDT by the magnetic particle process as required by AASHTO/AWS D1.5 2002, Bridge Welding Code clause 6.7.2.
 +
 
 +
<div id="Rock Blanket"></div>
 +
 
 +
'''Rock Blanket'''
 
   
 
   
:The baseline of the wall shown is for a vertical wall. If a battered wall system is used, this baseline shall correspond to Elevation <u>&nbsp; &nbsp; &nbsp; &nbsp; </u>.
+
'''(I1.70) Use note for redecks or in other cases where the rock blanket elevations are not shown on the bridge plans and the top of the rock blanket is required to be flush to the existing ground line in accordance with the Memorandum of Agreement with SEMA.'''
  
 +
:The top of rock blanket shall be flush to the ground line as directed by the engineer. (Roadway Item)
 +
<div id="(I1.71)  Use"></div>
 +
'''(I1.71)  Use only when specified on the Bridge Memo or Design Layout.'''
  
'''For Walls Near Bridge Abutments (Responsibility of Bridge Division)'''
+
:Rubblized concrete from the existing bridge deck that qualifies as clean fill may be placed on spill slopes at end bents above ordinary high water line (Roadway item).
  
'''(J1.15)'''
+
=== I2. Resin & Cone Anchors ===
:The contractor shall be solely responsible to coordinate construction of the wall with bridge and roadway construction and ensure that the bridge and roadway construction, resulting or existing obstructions, shall not impact the construction or performance of the wall. Soil reinforcement shall be designed and placed to avoid damage by pile driving, guardrail post installation, utility and sign foundations. (See Roadway and Bridge plans.)
 
  
 +
'''Use Resin Anchors unless concrete depths are insufficient.'''
  
'''PREQUALIFIED MSE WALL SYSTEMS'''
+
'''(I2.1)'''
 +
:The contractor shall use one of the qualified resin anchor systems in accordance with Sec 1039.
  
'''(J1.16) <font color="purple">[MS Cell]</font color="purple">'''
+
'''(I2.2) * Pay item in which resin anchor system is embedded.'''
:{|border="0" style="text-align:center;" cellpadding="5" cellspacing="0"
+
:Cost of furnishing and installing the resin anchor systems, complete in place, will be considered completely covered by the contract unit price for <u>*</u>.
|-
+
 
!colspan="6" style="border-top:3px solid black; border-bottom:1px solid black; border-left:3px solid black; border-right:3px solid black"|MSE Wall Systems Data Table
+
'''(I2.3)'''
|-
+
:The minimum embedment depth in concrete with f'<sub>c</sub> = 4,000 psi for the resin anchor systems shall be that required to meet the minimum ultimate pullout strength in accordance with Sec 1039 but shall not be less than 5".
!colspan="2" style="border-top:1px solid black; border-bottom:1px solid black; border-left:3px solid black; border-right:1px solid black"|Proprietary Wall<br/>Systems
+
 
!colspan="4" style="border-top:1px solid black; border-bottom:1px solid black; border-left:1px solid black; border-right:3px solid black"|Combination Wall Systems
+
'''Note to designer:'''<br/>A minimum factor of safety of 2 should be used when determining the number of anchors to be used.
 +
 
 +
'''(I2.4)(Use when reinforcing steel is substituted for the threaded rod stud.)'''
 +
:<u>A</u> <u>An epoxy coated</u> #<u>****</u> Grade 60 reinforcing bar <u>*****</u> long shall be substituted for the <u>******</u>&oslash; threaded rod.
 +
 
 +
 
 +
{|
 +
|****||Bar size.
 
|-
 
|-
!style="border-top:1px solid black; border-bottom:1px solid black; border-left:3px solid black; border-right:1px solid black"|Manufacturer
+
|*****||Length of bar required by design.
!style="border-top:1px solid black; border-bottom:1px solid black; border-left:1px solid black; border-right:1px solid black"|System
 
!style="border-top:1px solid black; border-bottom:1px solid black; border-left:1px solid black; border-right:1px solid black"|Facing Unit<br/>Manufacturer
 
!style="border-top:1px solid black; border-bottom:1px solid black; border-left:1px solid black; border-right:1px solid black"|Facing<br/>Unit
 
!style="border-top:1px solid black; border-bottom:1px solid black; border-left:1px solid black; border-right:1px solid black"|Geogrid<br/>Manufacturer
 
!style="border-top:1px solid black; border-bottom:1px solid black; border-left:1px solid black; border-right:3px solid black"|Geogrid
 
 
|-
 
|-
!style="border-top:1px solid black; border-bottom:1px solid gray; border-left:3px solid black; border-right:1px solid black"| &nbsp;
+
|******||Diameter of threaded rod.
!style="border-top:1px solid black; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"| &nbsp;
+
|}
|style="border-top:1px solid black; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"| &nbsp;
+
 
|style="border-top:1px solid black; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"| &nbsp;
+
 
|style="border-top:1px solid black; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"| &nbsp;
+
'''Cone Expansion Anchors'''
|style="border-top:1px solid black; border-bottom:1px solid gray; border-left:1px solid black; border-right:3px solid black"| &nbsp;
+
 
|-
+
'''(I2.30)  ***  Pay item in which cone expansion anchor is embedded.'''
!style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:3px solid black; border-right:1px solid black"| &nbsp;
+
:Cost of furnishing and installing cone expanson anchor will be considered completely covered by the contract unit price for <u>***</u>.
!style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"| &nbsp;
+
 
|style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"| &nbsp;
+
'''(I2.31)'''
|style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"| &nbsp;
+
:The <u>*</u>" diameter cone expansion anchors shall have a minimum ultimate pullout strength of <u>**</u> lbs. in concrete with f'<sub>c</sub> = 4,000 psi.
|style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"| &nbsp;
+
 
|style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:3px solid black"| &nbsp;
+
{|style="text-align:center;"  
 +
|-
 +
|width="100pt"|* DIAMETER||width="100pt"|** PULLOUT
 +
|-
 +
|3/8"||3,900
 
|-
 
|-
!style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:3px solid black; border-right:1px solid black"| &nbsp;
+
|1/2"||7,500
!style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"| &nbsp;
 
|style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"| &nbsp;
 
|style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"| &nbsp;
 
|style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:1px solid black"| &nbsp;
 
|style="border-top:1px solid gray; border-bottom:1px solid gray; border-left:1px solid black; border-right:3px solid black"| &nbsp;
 
 
|-
 
|-
!style="border-top:1px solid gray; border-bottom:3px solid black; border-left:3px solid black; border-right:1px solid black"| &nbsp;
+
|5/8"||10,800
!style="border-top:1px solid gray; border-bottom:3px solid black; border-left:1px solid black; border-right:1px solid black"| &nbsp;
 
|style="border-top:1px solid gray; border-bottom:3px solid black; border-left:1px solid black; border-right:1px solid black"| &nbsp;
 
|style="border-top:1px solid gray; border-bottom:3px solid black; border-left:1px solid black; border-right:1px solid black"| &nbsp;
 
|style="border-top:1px solid gray; border-bottom:3px solid black; border-left:1px solid black; border-right:1px solid black"| &nbsp;
 
|style="border-top:1px solid gray; border-bottom:3px solid black; border-left:1px solid black; border-right:3px solid black"| &nbsp;
 
 
|-
 
|-
|colspan="6" align="left"|MSE Wall Systems Data Table is to be completed by MoDOT construction personnel<br/> to record the manufacturer of the proprietary wall system or the manufacturers of the<br/>combination wall system that was used for constructing the MSE wall.
+
|3/4"||12,000
 
|}
 
|}
  
'''(J1.17) Use for all large block walls or if small block walls are to be built vertical.'''
+
=== I3. Special Repair Zones  - Deck Repair Notes for CIP Continuous Concrete Box Girder, Voided Slab and Solid Slab Spans (Notes for Bridge Standard Drawings RHB03 & RHB04)===
:The MSE wall system shall be built vertical.
 
  
'''(J1.18) Use where only a small or large block wall shall be used. Do not use note where either a small or large block may be used.'''
+
'''Use applicable notes I3.1 thru I3.6 under the special repair zones heading in the deck repair notes. The special repair zones heading shall follow the order of repair heading.'''
:The MSE wall system shall be a <u>small</u> <u>large</u> block wall system.
 
  
'''(J1.19)'''
+
'''(I3.1) Use for structures using conventional deck repair only (no hydro demolition). '''
:Topmost layer of reinforcement shall be fully covered with select granular backfill for structural systems, as approved by the wall manufacturer, before placement of the Separation Geotextile.
+
:Any deck repair in areas not designated as a special repair zone shall be completed prior to work in Zone A.  
  
'''(J1.19a)'''  
+
'''(I3.2) Use for structures with multiple column bents.'''  
:Minimum 6” diameter perforated PVC or PE pipe, unless larger size pipes are required by design by wall manufacturer.  
+
:Deck repair required in the areas designated as special repair zones shall be completed <u>pre-hydro demolition</u> in alphabetical sequence beginning with Zone A. Zones with the same letter designation may be repaired at the same time. <u>Hydro demolition shall not move forward until the repairs in all special repair zones are completed and properly cured.</u>
  
'''(J1.20)'''
+
'''(I3.3) Use for structures with single column bents. '''
:Adjustment in the vertical alignment of the drainage pipes from that depicted in the plans may be necessary to ensure positive flow out of the drainage system.
+
:Deck repair required in the areas designated as special repair zones shall be completed <u>pre-hydro demolition</u> in alphabetical sequence beginning with Zone A. Zones with the same letter designation may be repaired at the same time except for the zones directly adjacent to the centerline of bent. If either of the zones adjacent to centerline of bent has a single repair area of over 10 square feet or a total repair area of over 20 square feet, that zone shall be repaired before removing concrete in the other zone of the same designation at that bent. <u>Hydro demolition shall not move forward until the repairs in all special repair zones are complete and properly cured.</u>
 
:Outlet ends of pipes shall be located to avoid clogging or flow into the drainage system.
 
  
'''(J1.20a) '''
+
'''(I3.4) Use for hydro demolition projects. '''
:Select granular backfill shall extend a minimum of 12" beyond the end of all soil reinforcement. Where the angle, Ɵ, between the retained backfill excavation/fill line and the horizontal is less than 90°, the wedge area backfill between Ɵ and 90° shall be filled with select granular backfill for structural systems meeting the requirements of Section 1010.
+
:Any deck repair in areas not designated as a special repair zone shall be completed post-hydro demolition.  
  
::- For (45°+ Ф<sub>b</sub>/2) < Ɵ ≤ 90°, properties for retained backfill shall be used for active force computations.
+
'''(I3.5)'''
 +
:Removal and deck repair shall be completed in one special repair zone and concrete shall have attained a compressive strength of 3200 psi before work can be started in the next special repair zone.
  
::- For Ɵ ≤ (45°+ Ф<sub>b</sub>/2), contractor shall have the option to use properties for select granular backfill, Ф<sub>r</sub>, or better aggregate material, Ф<sub>w</sub> for active force computations in the wedge area backfill. For active force computations, the angle of internal friction for wedge area backfill material, Ф<sub>r</sub> or Ф<sub>w</sub>, shall be limited to 34° unless determined otherwise in accordance with Section 1010. If Ф<sub>r</sub> or Ф<sub>w</sub> > 34° is desired for wedge area backfill then test report shall be submitted with manufacturer's design plans.  Ф<sub>r</sub> or Ф<sub>w</sub> shall not be greater than 40°. Final configuration of this option shall be sent to Geotechnical Section for a new overall global stability analysis. Design Ф<sub>w</sub> shall be shown on manufacturer's plans if used.  
+
'''(I3.6) Use for voided or solid slab structure.'''
 +
:If any single repair area does not exceed 4 square feet in size and the total repair area within a special repair zone does not exceed 12 square feet, the special repair zone may be repaired at the same time as an adjacent zone.  
  
:The slope excavation line shall be benched and separation geotextile shall be placed between the retained backfill and either select granular backfill or better aggregate material, and between the select granular backfill and better aggregate material.
+
'''Use for voided slab structures, place applicable notes I3.10 thru I3.12 under the void repair heading in the deck repair notes. The void repair heading shall follow the special repair zones heading.'''
  
'''(J1.21) Use for all large block walls.'''
+
'''(I3.10) '''
:Inverted U-shape reinforced capstone may be used in lieu of coping. Panel dowels for capstone shall be required and as provided by manufacturer.
+
:Any damage sustained to the void tube as a result of the contractor's operations shall be patched or replaced as required by the engineer at the contractor's expense.
  
'''(J1.22)'''
+
'''(I3.11) Underline portion only required for Hydro Demo Case 2 details.'''
:The MSE wall system shall be built in accordance with Sec 720.
+
:An exposed void in the deck shall be patched as approved by the engineer in a manner that shall maintain the void area completely free of concrete. Cost of patching an exposed void will be considered completely covered by the contract unit price for Half-Sole Repair <u>inside special repair zones and Monolithic Deck Repair outside special repair zones</u>.  
  
'''(J1.23)  Use for MSE Walls when there may be contact between dissimilar metals.'''
+
'''(I3.12)  Use when deck repair with void tube replacement is required.'''
:All steel soil reinforcements shall be separated from other metallic elements by at least 3 inches.
+
:When a deteriorated portion of the void tube is beyond the point of patching as determined by the engineer, the portion of the deteriorated void tube shall be replaced. The void area shall be maintained completely free of concrete. Cutting of the longitudinal reinforcing steel will not be permitted. The fiber tubes for producing the voids shall have an outside diameter with the wall thickness the same as the existing tubes and anchored at not more than the original spacing. Cost of replacing the void tube will be considered completely covered by the contract unit price for Deck Repair with Void Tube Replacement. Measurement will be horizontal projection of the area of exposed tube in plan.
  
'''(J1.24)  Use for MSE Walls when there may be vertical obstructions in reinforced soil mass.'''
 
:The splay angle should be less than 15° and tensile capacity of splayed reinforcement shall be reduced by the cosine of the splay angle.
 
  
:No reinforcement shall be left unconnected to the wall face or arbitrarily cut/bent in the field to avoid the obstruction.
+
'''Use for box and deck girder structures, place applicable notes I3.16 thru I3.22 as a continuation of the special repair zones heading in the deck repair notes. '''
  
:Where interference between the vertical obstruction and the soil reinforcement is unavoidable, the design of the wall near the obstruction may be modified using one of the alternatives in FHWA-NHI-10-24, Section 5.4.2.  Show detail layout on the drawings. For wall designs with horizontal obstructions in reinforced soil mass, see FHWA-NHI-10-024, Section 5.4.3.
+
'''(I3.16)'''
 +
:Total width of full depth repair shall not exceed 1/3 of the deck width at one time. For any area of deck repair that extends over a web and is more than 18 inches in length along the web, the concrete removal <u>including removal with hydro demolition</u> shall stop at the centerline of web and repair completed in this area. Prior to continuing work in this area, the concrete shall have attained a compressive strength of 3200 psi. No traffic shall be permitted over the web that is undergoing repair.  
  
<div id="(J1.25)"></div>
+
'''(I3.17)'''
'''(J1.25) '''
+
:When the full depth repair extends over a diaphragm or web and the deteriorated concrete extends into the diaphragm or web, all deteriorated concrete shall be removed and replaced as full depth repair. Concrete in webs shall not be removed below the slab haunch of the girder without prior review and approval from the engineer.
:<u>The allowable bearing pressure for unimproved ground _____ ksf.</u>
 
:<u>The allowable bearing pressure for improved ground _____ ksf.</u>
 
  
(The allowable bearing pressure shall be determined by the Geotechnical Section and reported on the Foundation Investigation Geotechnical Report.)
 
<div id="For Small Block Walls"></div>
 
  
'''For Small Block Walls'''
+
'''Use notes I3.20 and I3.22 for box girder structures only. '''
  
'''(J1.26)''' Permanent shims for Small block MSE wall:
+
'''(I3.20)'''
 +
:Interior falsework installed by the contractor resting on the bottom slab shall be removed where entry access is available.
  
Shims will be sparingly allowed to maintain horizontal and vertical control. The preferable shim shall be made of a plastic material that will not rust, stain, rot or leach onto the concrete and has a minimum compressive strength equal to block wall unit.  Steel or wood shims will not be allowed. Shims shall not exceed 3/16” in thickness and shall distribute load in order to not induce stress into block wall units. No shim shall be used between the concrete leveling pad and the base course of the block wall.
+
'''(I3.21) This applies for each zone and not similarly lettered zones as a group. '''
 +
:If any single repair area does not exceed 9 square feet in size and the total repair area within a special repair zone does not exceed 27 square feet, the special repair zone may be repaired at the same time as an adjacent zone.  
  
'''(J1.27)'''  
+
'''(I3.22)'''
:Holes shall be 5/8” round and extend 4” into the third layer of blocks, recessed 2” deep by 1 1/2" round.
+
:Half-sole repair in the special repair zone, on either side of the intermediate bents, shall be to a depth that will not expose half the diameter of the longitudinal reinforcing bar. Full depth repair shall be made when removal of deteriorated concrete exposes half or more of the diameter of the longitudinal reinforcing bar.  
 
'''(J1.28) '''
 
:Rods or reinforcing bars shall be secured by an approved resin anchor system in accordance with Sec 1039.
 
  
'''(J1.29) '''
+
'''(I3.30) Use for hydro demolition projects.''' Place the following under the order of repair heading as the first of the deck repair notes. Remove portions not required. Typically (1) equals ½ inch; (2) equals ¼ inch; and (3) equals ½ inch; see Bridge Memorandum.
:Recess hole shall be backfilled with non-shrink cement grout.
+
:1. <u>Scarify existing deck (1).</u> <u>Remove existing wearing surface plus (1) of existing deck.</u>
 +
:<u>2. Power wash deck to identify sound and unsound existing deck repair.</u>
 +
:3. Inside special repair zones, complete the following repair<u>s</u>:
 +
::a. <u>Removal of existing deck repair</u>
 +
::<u>b.</u> Half-sole repair
 +
::<u>c. Deck repair with void tube replacement</u>
 +
::<u>d. Full depth repair</u>
 +
:<u>4. Outside special repair zones, remove existing deck repair.</u>
 +
:5. Complete total surface hydro demolition, removing (2) minimum of sound concrete inside special repair zones and removing (3) minimum of sound concrete and all deteriorated concrete outside special repair zones.
 +
:6. Sound deck and if needed complete incidental concrete removal.
 +
:''(Guidance: Use for Case 1 RHB03)''
 +
:<u>7. Outside special repair zones, complete full depth repair.</u>
 +
:''(Guidance: Use for Case 2 RHB03 and Case 1 & 2 RHB04)''
 +
:<u>7. Outside special repair zones, complete the following repairs:</u>
 +
::<u>a. Half-sole repair</u> ''(Guidance: Case 2 RHB04)''
 +
::<u>b. Deck repair with void tube replacement</u> ''(Guidance: Case 1 & 2 RHB04)''
 +
::<u>c. Full depth repair</u> ''(Guidance: Case 2 RHB03 and Case 1 & 2 RHB04)''
 +
:8. Place new wearing surface including additional material for areas of monolithic deck repair.
  
== K. Approach Slab Notes (Notes for Bridge Standard Drawings)==
+
'''(I3.31) Use for non-hydro demolition projects (conventional deck repair only).''' Place the following under the order of repair heading as the first of the deck repair notes. Remove portions not required. Typically (1) equals ½ inch; see Bridge Memorandum.
 +
:1. <u>Scarify existing deck (1).</u> <u>Remove existing wearing surface</u> <u>plus (1) of existing deck.</u>
 +
:2. Sound deck to identify areas in need of repair.
 +
:3. Outside special repair zones, complete the following repair<u>s</u>:
 +
::a. Half-sole repair
 +
::<u>b. Deck repair with void tube replacement</u>
 +
::<u>c. Full depth repair</u>
 +
:4. Inside special repair zones, complete the following repair<u>s</u>:
 +
::a. Half-sole repair
 +
::<u>b. Deck repair with void tube replacement</u>
 +
::<u>c. Full depth repair</u>
 +
:5. Place new wearing surface.
  
 +
===I4. Fiber Reinforced Polymer (FRP) Wrap - Bent Cap Shear Strengthening===
  
=== K1. General ===
+
'''(I4.1)'''
 +
:Design force is the factored shear force at any cross section in each design region that shall be resisted entirely by the FRP reinforcement.
  
'''(K1.1) Use for Bridge Approach Slab (Major Road) and omit underlined part for concrete sub-class Bridge Approach Slab (Minor Road).'''
+
'''(I4.2)'''
:All concrete for the bridge approach slab <u>and sleeper slab</u> shall be in accordance with Sec 503 (f'<sub>c</sub> = 4,000 psi).
+
:See special provisions.
  
'''(K1.2)'''
+
== J. MSE Wall Notes (Notes for Bridge Standard Drawings)==
:All joint filler shall be in accordance with Sec 1057 for preformed fiber expansion joint filler, except as noted.
 
  
'''(K1.3) Use for Bridge Approach Slab (Major Road) and omit underlined part for concrete sub-class Bridge Approach Slab (Minor Road).'''
 
:The reinforcing steel in the bridge approach slab <u>and the sleeper slab</u> shall be epoxy coated Grade 60 with F<sub>y</sub> = 60,000 psi.
 
  
'''(K1.4)'''
+
=== J1. General ===
:Minimum clearance to reinforcing steel shall be 1 1/2", unless otherwise shown.
+
 
 +
'''(J1.1)'''
 +
:Factor of safety shall be 2.0 for overturning and 1.5 for sliding.
 +
 
 +
'''(J1.2)'''
 +
:The cost of joint filler and joint seal, complete in place, will be considered completely covered by the contract unit price for Concrete Traffic Barrier (Type <u>A</u> <u>D</u>). See Roadway Plans.
 +
 
 +
'''(J1.3)'''
 +
:For seismic design the factor of safety shall be 1.5 for overturning and 1.1 for sliding.
 +
 
 +
'''(J1.4)'''
 +
:&oslash;<sub>b</sub> = <u>&nbsp; &nbsp;</u>&deg; and Unit weight, Ɣ<sub>b</sub> = ___pcf for retained backfill material to be retained by the mechanically stabilized earth wall system.
 +
 
 +
'''(J1.5)'''
 +
:<u>&oslash;<sub>f</sub> = &nbsp; &nbsp;&deg; for unimproved foundation ground where wall is to bear.</u>
 +
:<u>&oslash;<sub>f</sub> = &nbsp; &nbsp;&deg; for improved foundation ground where wall is to bear.</u>
 +
 
 +
'''(J1.6)'''
 +
:Actual ø<sub>r</sub> &ge; 34&deg; and the total unit weight, Ɣ<sub>r</sub> = _____pcf for the select granular backfill (reinforced backfill and wedge area backfill) for structural systems. Contractor shall identify source of select granular backfill material, submit proctor in accordance with AASHTO T 99 (ASTM D698) and gradation with the shop drawings. When backfill material is too coarse to develop a proctor curve the contractor shall determine the maximum dry density (relative density) in accordance with ASTM D4253 and ASTM D 4254 and assume percent passing the 200 sieve for optimum water content.
 +
 
 +
Total unit weight, Ɣ<sub>r</sub> = (95% compaction) x (maximum dry density) x (1 + optimum water content)
 +
 
 +
'''(J1.7)'''
 +
:Design Ф<sub>r</sub> = 34&deg; for the select granular backfill (reinforced backfill) only for structural systems.
 +
 
 +
'''(J1.8)'''
 +
:All concrete for