Difference between revisions of "Category:Minor Routes Shouldering Project Guidelines"

From Engineering_Policy_Guide
Jump to navigation Jump to search
(New article)
 
m
 
(9 intermediate revisions by 3 users not shown)
Line 1: Line 1:
Shoulders of any width provide the proven safety benefit of extra recovery area for errant vehicles.  The public perceives shoulders as an enhancement to the transportation system and have consistently identified them as a top tier desire.  In response, MoDOT has challenged their districts to assemble funding from any source possible and provide as many miles of shoulders on its minor routes as possible.  The following guidelines are offered as an aid to facilitate the design of these projects.
 
  
==Minimum Expectations==
 
  
:* The finished roadway has a consistent 2-4 ft. wide paved shoulder.
+
{|style="padding: 0.3em; margin-left:15px; border:2px solid #a9a9a9; text-align:center; font-size: 95%; background:#f5f5f5" width="240px" align="center"
 
+
|-
:* [http://epg.modot.org/index.php?title=Category:626_Rumble_Strips Edgeline rumble stripes] are provided.
+
|'''This article has moved'''
 
+
|-
:* No right of way is acquired except in unique, isolated circumstances.
+
|EPG Minor Routes Shouldering Project Guidelines has been replaced by [[231.4 Shoulder Width#231.4.3 Shoulder Widening Projects|EPG 231.4.3 Shoulder Widening Projects]].   
 
+
|}
:* Ditches, however altered, will have proper hydraulic function.
 
 
 
:* The traveled way should be overlaid with a 1 in. level course flush with the finished shoulder surface.
 
 
 
==Corridor Consistency==
 
 
 
:* Districts will collaborate on corridors that cross district lines.
 
 
 
:* Corridors will have logical termini.
 
 
 
:* In general, shoulder improvements should appear the same (to the public).
 
 
 
==NEPA==
 
 
 
:* A standard [[127.1 Request for Environmental Services|RES]] will be submitted for each project.
 
 
 
:* All projects will be classified as [http://epg.modot.mo.gov/index.php?title=127.14_National_Environmental_Policy_Act_(NEPA)_Classification_and_Documents#127.14.3.1_Categorical_Exclusion Categorical Exclusions (CE)].
 
 
 
:* Impacts to [[127.7 Threatened and Endangered Species (T&E)|threatened and endangered species]] or known [[127.2 Historic Preservation and Cultural Resources|cultural resources]] should be discerned.
 
 
 
==Conceptual Plans==
 
 
 
:* Shouldering jobs fall under the Federal 3R classification as defined in [http://ecfr.gpoaccess.gov/cgi/t/text/text-idx?c=ecfr&rgn=div5&view=text&node=23:1.0.1.7.18&idno=23 23CFR 625.2(b)], however.
 
 
 
:* A conventional [[:Category:128 Conceptual Studies|Conceptual Study Report]], instead of 3R, will be prepared.
 
 
 
:* The appropriate rural and urban 3R standards will apply to design.
 
 
 
:* Where 3R standards cannot be met, design exceptions will be submitted on a corridor-wide basis.
 
 
 
:* The [http://www.highwaysafetymanual.org/Pages/default.aspx ''Highway Safety Manual''] (HSM) analysis required of design exceptions may be waived given the narrowly focused scope of shouldering.
 
 
 
==Roadside Hardware==
 
 
 
:* All blunt ends, turned-down ends, and BCTs will be replaced with [http://epg.modot.mo.gov/index.php?title=606.1_Guardrail#606.1.3.2_Approved_Crashworthy_End_Terminals crashworthy end terminals].
 
 
 
:* The length of need (LON) need not be adjusted unless accident history or district policy presents the need to do so.
 
 
 
:* Guardrail that is in place but no longer needed will be removed.
 
 
 
:* If the height to the top of the guardrail is less than 26 ½ in. after construction, it should be increased to 29 inches. If the rail adjustment cannot be accommodated within the scope of the project, a design exception must be executed.
 
 
 
==Rumble Stripes==
 
 
 
:* On rural sections, a 12 in. [[:Category:626 Rumble Strips|rumble stripe]] should be milled straddling the line between shoulder and traveled way.
 
 
 
:* In the event that the traveled way has not been overlaid, a 12 in. rumble stripe should be milled entirely on the shoulder surface, abutting the joint.
 
 
 
:* Centerline rumble stripes may be milled in isolated locations if the accident history reveals the need to do so.
 
 
 
==Signing==
 
 
 
:* Signs should be located as specified in [http://www.modot.mo.gov/business/standards_and_specs/documents/90302.pdf Std. Plan 903.02].
 
 
 
:* Signs not meeting Std Plan 903.02 may be relocated by Maintenance forces, or justified by [[131.1 Design Exception Process|design exception]].
 
 
 
==Drainage Structures==
 
 
 
:* A 2 ft. minimum width shoulder will be provided over all pipes 36 in. or less in diameterTo accomplish this,
 
 
 
::* Pipes may be extended, or
 
 
 
::* Slopes may be warped within reason.
 
 
 
:* Shoulders may be narrowed or discontinued over box culverts and pipes over 36 in. in diameter.
 
 
 
==Constructability==
 
 
 
Plans should include the [[media:Modified Shoulder JSP.doc|''Modified Shoulder Construction'' JSP]] which gives the contractor the option to pave the mainline and build the shoulders monolithically. The pavement team will determine if this method is applicable for areas of poor subgrade or shoulder widths wider than 2 feet.
 

Latest revision as of 14:06, 1 February 2021


This article has moved
EPG Minor Routes Shouldering Project Guidelines has been replaced by EPG 231.4.3 Shoulder Widening Projects.