Difference between revisions of "106.3.2.59 TM-59, Determination of the International Roughness Index"

From Engineering_Policy_Guide
Jump to navigation Jump to search
m (Per CM, re-wrote TM-59 to comply with new Sec 610.)
Line 1: Line 1:
−
This method determines the profilograph index of portland cement concrete pavement and asphaltic concrete surfaces. This method determines the profilogram index in English units only, not metric.
+
This method describes the procedure for determining the International roughness index (IRI) of pavement surfaces in English units.  
  
−
==106.3.2.59.1 Apparatus==
+
==106.3.2.59.1 Equipment==
−
The profilograph shall consist of a frame 25 ft. long supported upon wheels at either end. The profile shall be recorded from the vertical movement of a wheel attached to the frame at mid-point and in reference to the mean elevation of the points of contact with the road surface established by the support wheels.  See Figure 106.3.2.59.1, below.
 
  
−
[[image:106.7.59.1.gif|center|700px|thumb|<center>'''Fig. 106.3.2.59.1'''</center>]]
+
'''Inertial Profiler.''' The International roughness index (IRI) shall be measured with an inertial profiler (IP).  The IP shall meet the equipment requirements of AASHTO M 328, which include the following three primary transducers: (1) a height sensor that measures the distance between the pavement and a vehicle reference point, (2) an accelerometer that measures the vehicle vertical acceleration in response to the pavement profile and (3) a distance sensor that provides a location reference as the vehicle moves longitudinally (see Fig. 106.3.2.59.1). The IP shall also be equipped with an automated triggering system that can automatically start and stop data collection using a reference mark.  The IP shall store the profile elevation data at an interval of  2 in. or less and have a vertical measurement resolution of 0.001 in. or less.  The IP equipment may be either the low speed or high speed type.  The IP shall be capable of  exporting unfiltered raw profile data to a profilograph file (conforming to ASTM E 2560) that can be imported into the ProVAL software program.
  
−
1) The profilogram shall be recorded on a scale of one inch equal to 25 ft. longitudinally and one inch equal to one inch, or full scale, vertically.
+
[[image:106.3.2.59.1.jpg|center|750px|thumb|<center>'''Fig. 106.3.2.59.1'''</center>]]
 +
  
−
2) Motive power may be provided manually or by use of a propulsion unit powered with a gasoline engine using the manufacturer’s towing option. In operation, the profilograph should be moved at a speed no greater than a walk (about 4.5 mph). (Excessive speed will increase the profilograph index count.)
+
'''ProVAL.'''  The profilograph file shall be evaluated using the ProVAL software program.  ProVAL is a free program developed by The Transtec Group under contract with the FHWA.  The current program version is [http://www.roadprofile.com/ ProVAL 3.3] and can be downloaded.
  
−
3) Calibration of the profilograph shall be checked as follows:
+
==106.3.2.59.2 Inertial Profiler Certification Procedures==
−
::The horizontal scale is checked by running a known distance and scaling the result on the profilogram. This shall be conducted at least annually at the MoDOT approved test site. If the scale is off, the profilograph should be recalibrated.
 
  
−
::The vertical scale is checked by putting a calibration block of known thickness under the profile wheel and again scaling the result on the profilogram. This shall be conducted at the beginning of each day the machine is operated. If the scale is off, the cause of the incorrect height should be determined and corrected.
+
Each IP used for construction acceptance testing on a MoDOT project shall be annually certified (verified) at the Linn State Technical Colleg test site. The test site will have a known IRI in two wheel paths, measured with a reference profiler.
  
−
==106.3.2.59.2 Procedure==
+
The inertial profiler (IP) shall have its low- and high-pass filters set to zero prior to the certification test. The IP shall have any other controls set according to manufacturer’s specifications. The two sensors in the profiler shall be spaced 6 ft. apart.
  
−
===106.3.2.59.2.1 Automated Profilogram Evaluation===
+
The IP operator may perform trial profile runs prior to the certification testing. The IP shall start far enough in advance of the test section to reach data collection speed. The IP operator shall perform five profile runs on the test section collecting data in both wheel paths. The IP shall move at a constant speed over the test section. An IP with two sensors shall measure both wheel path profiles in a single pass. An IP with one sensor shall measure each wheel path profile individually.  Upon completion of testing, the IP operator shall provide the engineer a summary printout in the IP company software format of IRI values in English units (inches/mile) for all tests and the unfiltered profiles in profilograph format on a readable electronic storage device such as a CD or flash drive. Each summary report shall contain the following:
−
Automated profilogram evaluation will be used unless otherwise determined by the engineer.
 
  
−
The engineer’s profilogram from calibration test sections and assurance testing will be evaluated using automated trace reduction performed by an automated Ames unit with the following settings:
+
:a) Date and time
 +
:b) Operator identification
 +
:c) Equipment owner
 +
:d) Equipment identification for vehicle and IP equipment
 +
:e) Unique number profile
 +
:f) Software name and version
 +
:g) Profiler settings for filters
 +
:h) IRI values.
  
−
:a) Filter length: Low Pass = 3 to 4 (ft.), High Pass = 0.00 (ft.)
+
MoDOT will analyze the submitted data using ProVAL. The test results of the inertial profiler (IP) shall meet the following requirements:
  
−
::Filter length has the same effect as using the contrasting color to outline the trace, removing spikes and high frequency chatter.
+
:a) The IRI average of the five profiles shall be within 5 percent of the reference IRI value.
 +
:b) The IRI standard deviation of the five profiles shall be no larger than 3 percent of the IRI average of the five profiles.
 +
:c) Each individual IRI-filtered profile shall correlate with the reference IRI-filtered profile at a level of at least 85 percent.
 +
:d) The average of the five profile correlations shall be at least 92 percent.
 +
:e) Each individual profile length shall be within 0.2 percent of the actual test section length.
  
−
:b) Scallop rounding = 0.01 in.
+
An inertial profiler (IP) that receives acceptable test results at the certification site shall be furnished with an annual IP certification decal. The date of acceptance, unique identification number, IP model and manufacturer, vehicle make and model to which the IP is attached, operational system software version, and signature of a MoDOT Construction and Materials Division Engineer will be shown on the decal.
−
::This setting determines the amount of rounding given to any particular scallop. For example: In order to measure a defect to the nearest 0.05 in., the rounding on the machine must be set higher (finer) to accurately make that determination.
 
  
−
:c) Minimum Scallop height = 0.030 in. (in software, non-adjustable)
 
−
::Minimum Scallop width = 0.08 in. (in software, non-adjustable)
 
−
::Scallop height and width corresponds to existing standards. .08 in. is equal to 2 ft. on the roadway. 0.030 in. simply provides a means to count a defect that is more than 0.030 in. tall as 0.05.
 
  
−
:d) Template height for grind point = 0.4 in.
+
==106.3.2.59.3 Construction Acceptance Procedures==
−
::Corresponds to the standard bump template.
 
  
−
:e) Bump Width = 25 ft.
+
'''Testing Conditions.'''  All objects and foreign material shall be removed from the pavement surface.  There shall be no standing water in the wheel paths during testing.
  
−
:f) Band Width = 0.001 in.
+
'''Testing Limits.'''  The inertial profiler shall measure the surface of a pavement section in both wheel paths, that are located 3 ft. from and parallel to the edges of the lane, running in the direction of travel. 
  
−
===106.3.2.59.2.2 Manual Profilogram Evaluation===
+
:* The starting point shall be 50 ft. before the start of the day’s paving. 
−
To determine the profile index, use a transparent scale 1.70 in. wide and 21.12 in. long representing a pavement length of 528 ft. or one-tenth of a mile at a scale of 1 in. = 25 ft. Near the center of the scale is a dashed reference line extending the entire length of 21.12 in. On either side of this dashed reference line are scribed lines 0.1 in. apart. These lines serve as a convenient scale to measure deviations or excursions of the graph above or below the dashed reference line. These are called “scallops”.
+
:* The starting point shall be a known station or logmile measured to the nearest foot.
 +
:* The IP shall use an automated triggering mechanism to initiate data collection at the starting point and end data collection at the ending point.  
 +
:* The starting point shall be visibly marked for the duration of the project so that subsequent profile measurements may be closely matched.  
  
−
===106.3.2.59.2.3 Method of Counting===
+
'''Data Submittal.'''  The contractor shall submit an electronic file in profilograph format containing the unfiltered raw data collected at the section. <u>Data shall be submitted within 24 hours of the testing on each section.</u>  A day's report may consist of more than one section. Profilograph files with QC data results shall be submitted to MoDOT using the naming convention in Table 106.3.2.59.3.
−
Place the transparent scale over the profile in such a way as to center it on the profile as much as possible. When this is done, scallops above and below the dashed reference line usually will be approximately balanced. See Figure 106.3.2.59.2, below.
 
  
−
[[image:106.7.59.2.gif|center|800px|thumb|<center>'''Fig. 106.3.2.59.2'''</center>]]
+
<center>'''Table 106.3.2.59.3, Categories of Warning Signs and Plaques'''
−
 
+
{| border="1" class="wikitable" style="margin: 1em auto 1em auto" style="text-align:center"
−
The profile trace will move from a generally horizontal position when going around super-elevated curves making it impossible to center the trace without shifting the scale. When such conditions occur the profile should be broken into short sections and the dashed reference line repositioned on each section while counting as shown in the upper part of Figure 106.3.2.59.3.
 
−
 
 
−
[[image:106.7.59.3.gif|center|800px|thumb|<center>'''Fig. 106.3.2.59.3'''</center>]]
 
−
 
 
−
Short portions of the profile line may be visible above or below the dashed reference line but unless they project 0.03 in. or more and extend longitudinally for 2 ft. (0.08 in. on the profilogram) or more, they are not included in the count. See Figure 106.7.59.2 for illustration of these special conditions.) Starting at the right end of the scale, measure and total the height of all the scallops appearing both above and below the dashed reference line, measuring each scallop to the nearest 0.05 in. (half a tenth). Record this total on the profile sheet near the left end of the scale together with a small mark to align the scale when moving to the next section.
 
−
 
 
−
When scallops occurring in the first 0.1 mile are totaled, slide the scale to the left, aligning the right end of the scale with the small mark previously made, and proceed with the counting in the same manner. The last section counted may or may not be an entire 0.1 mile. If not, its length should be scaled to determine its length in miles. An example is as follows:
 
−
 
 
−
{| border="1" class="wikitable" style="margin: 1em auto 1em auto"
 
 
|+  
 
|+  
−
!  !!style="background:#BEBEBE"| Selection Length, miles !! style="background:#BEBEBE"| Count, inches
+
! style="background:#BEBEBE" colspan="2"|Electronic Profilograph File Naming Convention*
 +
|-
 +
|Abbreviation|| Definition
 +
|-
 +
|YYMMDD-###_ ||Contract ID (Letting Date-Call Number)
 +
|-
 +
|YYMMDD_ ||Test Date
 +
|-
 +
|Q_ ||Type of quality test (C for control, A for assurance)
 
|-
 
|-
−
| ||align="center"|0.10 || align="center"|.50
+
|D ||Direction of Lane (N,E,W or S)
 
|-
 
|-
−
| || align="center"|0.10 || align="center"|.40
+
|L ||Lane number (1 for driving lane, increasing by one for each lane to the left)
 
|-
 
|-
−
| || align="center"|0.10 || align="center"|.35
+
|W ||Wheel path (L, R, or B)
 
|-
 
|-
−
| || align="center"|0.076|| align="center"| .20
+
|S ||Beginning Station (rounded to nearest foot)
 
|-
 
|-
−
|400 ft. = Total || align="center"|0.376|| align="center"|1.45
+
|colspan="2" align="left"|* Example:  100528-501_111103_C_N2R105045.PPF
 
|}
 
|}
 +
</center>
 +
 +
'''Data Analysis.''' After the profile data for a section of pavement has been collected, the contractor shall use the ProVAL program to analyze the results using the same unfiltered profilograph data file that was submitted to MoDOT.  ProVAL shall be used for both quality control and quality assurance test data.  The analysis will consist of two primary components [1] ''segment smoothness'' evaluated with the "Ride Quality" module and [2] ''areas of localized roughness'' (ALR) evaluated with the "Smoothness Assurance" module.  The contractor shall submit hardcopy of the ProVAL summary report in pdf file format to the engineer within seven calendar days of the profile data collection.
 +
 +
===106.3.2.59.3.1 Segment Smoothness===
 +
The data will first be analyzed for ride quality, which will determine the average IRI for each wheel track on a per segment basis.  The steps are as follow:
 +
 +
:* '''Open ProVAL program.'''
 +
 +
:* '''Select "New".'''
 +
 +
[[image:106.3.2.59.1 new.jpg|center|750px]]
 +
 +
 +
:* '''Select "Add Files" to import PPF file with QC/QA profile data.  '''
 +
 +
The file(s) will either be a single one containing both right and left wheel track profiles or a pair of files with each containing one of the wheel track profiles.
 +
 +
[[image:106.3.2.59.1 add files.jpg|center|750px]]
 +
 +
 +
:* '''Select left elevation and right elevation.  '''
 +
 +
The program will correctly align separate files with each other, provided the data collection was initiated at the same starting station for both files.
 +
 +
[[image:106.3.2.59.1 left right.jpg|center|750px]]
 +
 +
 +
:* '''Select "Ride Quality" in the "Analysis" module.'''
 +
 +
[[image:106.3.2.59.1 ride.jpg|center|750px]]
 +
 +
:* '''Select "Fixed Interval" in the "Analysis Type" dropdown box.'''
 +
 +
:* '''Change "Threshold" limit to 80 (in/mi).  The "Segment Length" should show the default value of 528 ft. and the "Ride Quality Index" should show the default name of "IRI".'''
 +
 +
:* '''Check box for "LElev." and "RElev." and make sure the "Apply 250mm Filter" box is checked for both.'''
 +
 +
[[image:106.3.2.59.1 LElev.jpg|center|750px]]
 +
 +
 +
:* '''Select "Analyze".  '''
 +
 +
The average IRI of a wheel path for each 528 ft. long segment will be shown on the screen. The drop down menu above table at left can be used to view either left or right wheel path IRI values
 +
 +
[[image:106.3.2.59.1 analyze.jpg|center|750px]]
 +
 +
:* '''Select "PDF" in "Report" dropdown box.'''
 +
 +
[[image:106.3.2.59.1 report.jpg|center|750px]]
 +
 +
 +
Average IRI over a 528 ft long segment for each wheel track is listed in the report table. 
 +
 +
:* '''Manually enter this data into the IRI Summary Worksheet.'''
 +
 +
[[image:106.3.2.59.1 IRI summary.jpg|center|900px]]
 +
 +
 +
[[image:106.3.2.59.1 CIA.jpg|center|750px]]
 +
 +
:* '''Save a copy of the Ride Quality report in the CIA project folder.'''
 +
 +
There may be exempted areas per [http://www.modot.org/business/standards_and_specs/Sec0601.pdf Sec 601.4.2.2] within the section profile limits.  The engineer should verify that the limits do not go beyond the eligible exemption area.  The contractor may elect to:
 +
 +
:1) Stop the profile run at the beginning of the exemption and begin a new section profile at the end of the exemption.
 +
:2) Manually enter exemption boundaries in the data acquisition software during the profile run (typically performed with high speed IPs).
 +
:3) Enter a "leave-out" area in ProVAL during the ride quality analysis.  The instructions for performing this are as follows:
 +
 +
:* '''Select "Editor". Select the file from the File dropdown menu.'''
 +
 +
:* '''Select "Sections" in the "Navigate" drop down box.'''
 +
 +
[[image:106.3.2.59.1 navigate.jpg|center|750px]]
 +
 +
 +
:* '''Select "Add Section".'''
 +
 +
[[image:106.3.2.59.1 add section.jpg|center|750px]]
 +
 +
 +
:* '''Enter section(s) Start Distance, Stop Distance, Type (Leave-out) and Name.'''
 +
 +
:* '''Select "Analysis" and select "Ride Quality".'''
 +
 +
[[image:106.3.2.59.1 ride quality.jpg|center|750px]]
 +
 +
 +
The ride quality summary shown below now excludes the exempted areas of the profile and abbreviates the associated segments accordingly.
 +
 +
===106.3.2.59.3.2 Areas of Localized Roughness===
 +
 +
:* '''Select "Smoothness Assurance" in "Analysis" module.'''
 +
 +
[[image:106.3.2.59.2 smoothness.jpg|center|750px]]
 +
 +
 +
:* '''Change "Threshold" value to 125 (in/mi) for "Short Continuous" analysis in the "Ride Quality" section. (The segment length for "Short Continuous" should be set at the default value of 25 ft.)'''
 +
 +
:* '''Check "Right Elevation" only in the "Profile" section (make sure "Apply 250mm Filter" is also checked).'''
 +
 +
:* '''Change "Threshold" to 80 (in/mi) for "Long Continuous" and "Fixed Interval" in the "Profile" section.  (The "Segment Length" should be set at the default value of 528 ft. for both "Long Continuous" and "Fixed Interval".)'''
 +
 +
:* '''Select "Analyze".'''
 +
 +
[[image:106.3.2.59.2 analyze.jpg|center|750px]]
 +
 +
 +
:* '''Select "Grinding" in the "Navigate" dropdown box.'''
 +
 +
[[image:106.3.2.59.2 navigate.jpg|center|760px]]
 +
 +
 +
:* '''Enter 0.25 inches for "Maximum Grinding Depth" in "Grinder" section. (The following parameters should show the default values, which are Head Position = 0.50, Wheelbase (ft) = 18, Tandem Spread (ft) = 2.49 and Short Cut-Off Wavelength (ft) = 0.82 ft.)'''
 +
 +
:* '''Select "Auto Grind".'''
 +
 +
[[image:106.3.2.59.2 autogrind.jpg|center|750px]]
  
−
The procedure for converting counts of profile index is as follows:
+
 
 +
:* '''Select "Grind".'''
  
−
:Using the figures from the above example:
+
[[image:106.3.2.59.2 grind.jpg|center|750px]]
−
::Profile Index = (1.45 in.) / (0.376 miles) = 3.9 in./mile
 
  
−
===106.3.2.59.2.4 Limits of Counts - Joints===
 
−
When counting profiles, a day’s paving is considered to include the last portion of the previous day’s work, which includes the daily joint. The last 15 to 30 ft. of a day’s paving cannot usually be obtained until the following day. In general, the paving contractor is responsible for the smoothness of joints if pavement is placed on both sides of the joint. On the other hand, the contractor is responsible only for the pavement placed if the work abuts a bridge or a pavement placed under another contract. Profilograph readings when approaching such joints should be taken in accordance with the standard specifications.
 
  
−
===106.3.2.59.2.5 Average Profile Index for a Section===
+
:* '''Select "Short Continuous" in "Navigate" dropdown box.'''
−
When averaging profile indexes to obtain an average for a section, the average for each segment must be “weighted” according to its length.  See Figures 106.3.2.59.4 and 106.3.2.59.5. Figure 106.3.2.59.4 is an example when the last segment is longer than 250 ft. and Figure 106.3.2.59.5 is an example when the last segment is less than 250 ft.).
 
  
−
[[image:106.7.59.4.gif|center|700px|thumb|<center>'''Fig. 106.3.2.59.4'''</center>]]
+
[[image:106.3.2.59.2 short continuous.jpg|center|760px]]
  
−
[[image:106.7.59.5.gif|center|700px|thumb|<center>'''Fig. 106.3.2.59.5'''</center>]]
+
 +
:* '''Select "PDF" in "Report" dropdown box.'''
  
 +
[[image:106.3.2.59.2 report.jpg|center|750px]]
  
−
===106.3.2.59.2.6 Determination of High Points in excess of 0.4 in.===
 
−
Use a transparent bump template having a line one-inch long scribed on one face with a small hole or scribed mark at either end and a slot 0.4 inch from and parallel to the scribed line. See Figure 106.3.2.59.3. (The one-inch line corresponds to a horizontal distance of 25 ft. on the horizontal scale of the profilogram).
 
  
−
===106.3.2.59.2.7 Locating High Points in Excess of 0.4 in.===
+
The grinding report is generated showing locations of areas of localized roughness (ALR). The grinding simulation numerically indicates what the expected improvement in smoothness should be when the ALRs are diamond ground. This information serves as a guide for both the contractor and the engineer for determining which ALRs can be corrected with conventional grinding and which may require other corrective measures.
−
At each prominent peak or high point on the profile trace, place the template so that the small holes or scribe marks at each end of the scribed end of the scribed line intersect the profile trace to form a chord across the base of the peak or indicated bump. The line on the template need not be horizontal. With a sharp pencil draw a line using the narrow slot in the template as a guide. Any portion of the trace extending above this line will indicate the approximate length and height of the deviation in excess of 0.4 in.
 
  
−
There may be instances where the distance between easily recognizable low points is less than one in. (25 ft.). In such cases a shorter chord length shall be used in making the scribed line on the template tangent to the trace at the low points. It is the intent, however, of this requirement that the baseline for measuring the height of bumps will be as nearly 25 ft. (1 in.) as possible, but in no case to exceed this value. When the distance between prominent low points is greater than 25 ft. (1 in.) make the ends of the scribed line intersect the profile trace when the template is in a nearly horizontal position. A few examples of the procedure are shown in the lower portion of Figure 106.3.2.59.3.
+
[[image:106.3.2.59.2 smoothness assurance.jpg|center|750px]]
 +
 +
 +
Comparisons for IRI before and after grinding are shown in tabular and bar graph form.
  
−
==106.3.2.59.3 Certified Operator==
+
[[image:106.3.2.59.2 comparisons.jpg|center|750px]]
−
The contractor shall furnish a certification stating that the test was performed by a trained operator. The operator must be certified as having been trained in the use of the profilograph and certified to have sufficient experience to demonstrate competence in the use of the equipment.
 
  
−
==106.3.2.59.4 Quality Control/Quality Assurance==
+
==106.3.2.59.4 Dispute Resolution==
−
The contractor’s quality control profilogram evaluation will be compared to the engineer’s quality assurance profilogram evaluation on a test section established by MoDOT and on a randomly selected portion of the work, usually ten percent of the project length. Automated profilogram evaluation using an automated Ames unit as outlined in [[#106.3.2.59.2.1 Automated Profilogram Evaluation|EPG 106.3.2.59.2.1 Automated Profilogram Evaluation]] will be the engineer’s basis for comparison.
+
[[image:106.3.2.59.4.jpg|right|170px|thumb|<center>'''MoDOT Reference Profiler '''</center>]]
 +
In the event that the QC/QA results are not within 6 inches/mile for each segment and the contractor disputes the results, the MoDOT reference profiler used for equipment certification shall arbitrate the dispute. A Construction and Materials Division tester shall randomly select a 528-ft. area within the disputed pavement length and run the MoDOT reference profiler in the left and right wheel paths. The arbitration profile shall be correlated with its corresponding QC and QA profiles in ProVAL. Whichever of the average QC/QA IRI profiles is closer to the arbitration IRI profile, up to a maximum difference of 6 inches/mile, shall be the binding profile for the purpose of construction acceptance.
  
  
 
[[Category:106.3.2 Material Inspection Test Methods]]
 
[[Category:106.3.2 Material Inspection Test Methods]]

Revision as of 15:17, 10 January 2013

This method describes the procedure for determining the International roughness index (IRI) of pavement surfaces in English units.

106.3.2.59.1 Equipment

Inertial Profiler. The International roughness index (IRI) shall be measured with an inertial profiler (IP). The IP shall meet the equipment requirements of AASHTO M 328, which include the following three primary transducers: (1) a height sensor that measures the distance between the pavement and a vehicle reference point, (2) an accelerometer that measures the vehicle vertical acceleration in response to the pavement profile and (3) a distance sensor that provides a location reference as the vehicle moves longitudinally (see Fig. 106.3.2.59.1). The IP shall also be equipped with an automated triggering system that can automatically start and stop data collection using a reference mark. The IP shall store the profile elevation data at an interval of 2 in. or less and have a vertical measurement resolution of 0.001 in. or less. The IP equipment may be either the low speed or high speed type. The IP shall be capable of exporting unfiltered raw profile data to a profilograph file (conforming to ASTM E 2560) that can be imported into the ProVAL software program.

Fig. 106.3.2.59.1


ProVAL. The profilograph file shall be evaluated using the ProVAL software program. ProVAL is a free program developed by The Transtec Group under contract with the FHWA. The current program version is ProVAL 3.3 and can be downloaded.

106.3.2.59.2 Inertial Profiler Certification Procedures

Each IP used for construction acceptance testing on a MoDOT project shall be annually certified (verified) at the Linn State Technical Colleg test site. The test site will have a known IRI in two wheel paths, measured with a reference profiler.

The inertial profiler (IP) shall have its low- and high-pass filters set to zero prior to the certification test. The IP shall have any other controls set according to manufacturer’s specifications. The two sensors in the profiler shall be spaced 6 ft. apart.

The IP operator may perform trial profile runs prior to the certification testing. The IP shall start far enough in advance of the test section to reach data collection speed. The IP operator shall perform five profile runs on the test section collecting data in both wheel paths. The IP shall move at a constant speed over the test section. An IP with two sensors shall measure both wheel path profiles in a single pass. An IP with one sensor shall measure each wheel path profile individually. Upon completion of testing, the IP operator shall provide the engineer a summary printout in the IP company software format of IRI values in English units (inches/mile) for all tests and the unfiltered profiles in profilograph format on a readable electronic storage device such as a CD or flash drive. Each summary report shall contain the following:

a) Date and time
b) Operator identification
c) Equipment owner
d) Equipment identification for vehicle and IP equipment
e) Unique number profile
f) Software name and version
g) Profiler settings for filters
h) IRI values.

MoDOT will analyze the submitted data using ProVAL. The test results of the inertial profiler (IP) shall meet the following requirements:

a) The IRI average of the five profiles shall be within 5 percent of the reference IRI value.
b) The IRI standard deviation of the five profiles shall be no larger than 3 percent of the IRI average of the five profiles.
c) Each individual IRI-filtered profile shall correlate with the reference IRI-filtered profile at a level of at least 85 percent.
d) The average of the five profile correlations shall be at least 92 percent.
e) Each individual profile length shall be within 0.2 percent of the actual test section length.

An inertial profiler (IP) that receives acceptable test results at the certification site shall be furnished with an annual IP certification decal. The date of acceptance, unique identification number, IP model and manufacturer, vehicle make and model to which the IP is attached, operational system software version, and signature of a MoDOT Construction and Materials Division Engineer will be shown on the decal.


106.3.2.59.3 Construction Acceptance Procedures

Testing Conditions. All objects and foreign material shall be removed from the pavement surface. There shall be no standing water in the wheel paths during testing.

Testing Limits. The inertial profiler shall measure the surface of a pavement section in both wheel paths, that are located 3 ft. from and parallel to the edges of the lane, running in the direction of travel.

  • The starting point shall be 50 ft. before the start of the day’s paving.
  • The starting point shall be a known station or logmile measured to the nearest foot.
  • The IP shall use an automated triggering mechanism to initiate data collection at the starting point and end data collection at the ending point.
  • The starting point shall be visibly marked for the duration of the project so that subsequent profile measurements may be closely matched.

Data Submittal. The contractor shall submit an electronic file in profilograph format containing the unfiltered raw data collected at the section. Data shall be submitted within 24 hours of the testing on each section. A day's report may consist of more than one section. Profilograph files with QC data results shall be submitted to MoDOT using the naming convention in Table 106.3.2.59.3.

Table 106.3.2.59.3, Categories of Warning Signs and Plaques
Electronic Profilograph File Naming Convention*
Abbreviation Definition
YYMMDD-###_ Contract ID (Letting Date-Call Number)
YYMMDD_ Test Date
Q_ Type of quality test (C for control, A for assurance)
D Direction of Lane (N,E,W or S)
L Lane number (1 for driving lane, increasing by one for each lane to the left)
W Wheel path (L, R, or B)
S Beginning Station (rounded to nearest foot)
* Example: 100528-501_111103_C_N2R105045.PPF

Data Analysis. After the profile data for a section of pavement has been collected, the contractor shall use the ProVAL program to analyze the results using the same unfiltered profilograph data file that was submitted to MoDOT. ProVAL shall be used for both quality control and quality assurance test data. The analysis will consist of two primary components [1] segment smoothness evaluated with the "Ride Quality" module and [2] areas of localized roughness (ALR) evaluated with the "Smoothness Assurance" module. The contractor shall submit hardcopy of the ProVAL summary report in pdf file format to the engineer within seven calendar days of the profile data collection.

106.3.2.59.3.1 Segment Smoothness

The data will first be analyzed for ride quality, which will determine the average IRI for each wheel track on a per segment basis. The steps are as follow:

  • Open ProVAL program.
  • Select "New".
106.3.2.59.1 new.jpg


  • Select "Add Files" to import PPF file with QC/QA profile data.

The file(s) will either be a single one containing both right and left wheel track profiles or a pair of files with each containing one of the wheel track profiles.

106.3.2.59.1 add files.jpg


  • Select left elevation and right elevation.

The program will correctly align separate files with each other, provided the data collection was initiated at the same starting station for both files.

106.3.2.59.1 left right.jpg


  • Select "Ride Quality" in the "Analysis" module.
106.3.2.59.1 ride.jpg
  • Select "Fixed Interval" in the "Analysis Type" dropdown box.
  • Change "Threshold" limit to 80 (in/mi). The "Segment Length" should show the default value of 528 ft. and the "Ride Quality Index" should show the default name of "IRI".
  • Check box for "LElev." and "RElev." and make sure the "Apply 250mm Filter" box is checked for both.
106.3.2.59.1 LElev.jpg


  • Select "Analyze".

The average IRI of a wheel path for each 528 ft. long segment will be shown on the screen. The drop down menu above table at left can be used to view either left or right wheel path IRI values

106.3.2.59.1 analyze.jpg
  • Select "PDF" in "Report" dropdown box.
106.3.2.59.1 report.jpg


Average IRI over a 528 ft long segment for each wheel track is listed in the report table.

  • Manually enter this data into the IRI Summary Worksheet.
106.3.2.59.1 IRI summary.jpg


106.3.2.59.1 CIA.jpg
  • Save a copy of the Ride Quality report in the CIA project folder.

There may be exempted areas per Sec 601.4.2.2 within the section profile limits. The engineer should verify that the limits do not go beyond the eligible exemption area. The contractor may elect to:

1) Stop the profile run at the beginning of the exemption and begin a new section profile at the end of the exemption.
2) Manually enter exemption boundaries in the data acquisition software during the profile run (typically performed with high speed IPs).
3) Enter a "leave-out" area in ProVAL during the ride quality analysis. The instructions for performing this are as follows:
  • Select "Editor". Select the file from the File dropdown menu.
  • Select "Sections" in the "Navigate" drop down box.
106.3.2.59.1 navigate.jpg


  • Select "Add Section".
106.3.2.59.1 add section.jpg


  • Enter section(s) Start Distance, Stop Distance, Type (Leave-out) and Name.
  • Select "Analysis" and select "Ride Quality".
106.3.2.59.1 ride quality.jpg


The ride quality summary shown below now excludes the exempted areas of the profile and abbreviates the associated segments accordingly.

106.3.2.59.3.2 Areas of Localized Roughness

  • Select "Smoothness Assurance" in "Analysis" module.
106.3.2.59.2 smoothness.jpg


  • Change "Threshold" value to 125 (in/mi) for "Short Continuous" analysis in the "Ride Quality" section. (The segment length for "Short Continuous" should be set at the default value of 25 ft.)
  • Check "Right Elevation" only in the "Profile" section (make sure "Apply 250mm Filter" is also checked).
  • Change "Threshold" to 80 (in/mi) for "Long Continuous" and "Fixed Interval" in the "Profile" section. (The "Segment Length" should be set at the default value of 528 ft. for both "Long Continuous" and "Fixed Interval".)
  • Select "Analyze".
106.3.2.59.2 analyze.jpg


  • Select "Grinding" in the "Navigate" dropdown box.
106.3.2.59.2 navigate.jpg


  • Enter 0.25 inches for "Maximum Grinding Depth" in "Grinder" section. (The following parameters should show the default values, which are Head Position = 0.50, Wheelbase (ft) = 18, Tandem Spread (ft) = 2.49 and Short Cut-Off Wavelength (ft) = 0.82 ft.)
  • Select "Auto Grind".
106.3.2.59.2 autogrind.jpg


  • Select "Grind".
106.3.2.59.2 grind.jpg


  • Select "Short Continuous" in "Navigate" dropdown box.
106.3.2.59.2 short continuous.jpg


  • Select "PDF" in "Report" dropdown box.
106.3.2.59.2 report.jpg


The grinding report is generated showing locations of areas of localized roughness (ALR). The grinding simulation numerically indicates what the expected improvement in smoothness should be when the ALRs are diamond ground. This information serves as a guide for both the contractor and the engineer for determining which ALRs can be corrected with conventional grinding and which may require other corrective measures.

106.3.2.59.2 smoothness assurance.jpg


Comparisons for IRI before and after grinding are shown in tabular and bar graph form.

106.3.2.59.2 comparisons.jpg

106.3.2.59.4 Dispute Resolution

MoDOT Reference Profiler

In the event that the QC/QA results are not within 6 inches/mile for each segment and the contractor disputes the results, the MoDOT reference profiler used for equipment certification shall arbitrate the dispute. A Construction and Materials Division tester shall randomly select a 528-ft. area within the disputed pavement length and run the MoDOT reference profiler in the left and right wheel paths. The arbitration profile shall be correlated with its corresponding QC and QA profiles in ProVAL. Whichever of the average QC/QA IRI profiles is closer to the arbitration IRI profile, up to a maximum difference of 6 inches/mile, shall be the binding profile for the purpose of construction acceptance.

Retrieved from "https://epg.modot.org/index.php?title=106.3.2.59_TM-59,_Determination_of_the_International_Roughness_Index&oldid=30535"